Chery A series. Manual — part 96

------If the trunk lid is to be adjusted

horizontally, move the hinge on the side
until the value of movement becomes
consistent to the designed adjusting
value. Adjustment can also be conducted
through moving the center of the top.

------After adjustment is finished, the

connecting surface of rear door and the
side shall be checked as to if it is even or
not, if the joint with sealing rubber is
satisfactory or not. A good joint can
provide the trunk lid with pressure seal,
which can prevent water, air and dust
from admission or give out the chick
sound.

------Check if the transparent plastic adhesive

tape for preventing rubber block from
contacting the coated paint of vehicle
body exists or not. If the tape does not
exist or it has already aged, isopropyl
alcohol or heptane is to be used for
cleaning the contact surface, and new
adhesive tape is to be pasted.

REMOVAL OF LOCK STRIKER
------Take out the screws of two lock

strikers, 2 for each. The screws are
on the side of luggage boot.

REMOVAL OF TOP PART OF
CENTRAL LOCK

------Remove the two screws of lower frame of

trunk lid to remove the top of central lock.

S-35

------Remove the two screws between the

bottom part of central lock and rear end
panel. For CHERY model—A15RHD
with luggage boot trim panel available,
the trim panel shall be removed before
removing the screws.

------Install lock in the reverse order of its

removal. Tightening torque for screws of
side locks is 7.2±0.7N·m. Tightening
torque for screw on top of lock striker is
7.2±0.7N·m

ADJUSTMENT OF LOCK AND TRUNK LID
------If the trunk lid fails to be closed properly due to its wrong position, it can be adjusted

through adjusting the position of lock striker.

------It is possible to make horizontal adjustment of the trunk lid, for there is a slot on its

top. Adjustment made is to assure an even clearance of 5±0.5mm between trunk lid
and rear side panels on two sides.

REMOVAL & INSTALLATON OF FRONT DOOR
GLASSES

REMOVAL：

----Before removal of front door glasses, the

trim panel and waterproof film shall be
removed first following instructions.

----Pull out the inner and outer door waterproof

strips; begin the removal from the rib of the
internal side of the central door frame.

----Place the glass at the center of the door

frame. Loosen the fixing slot of the
window regulator support.

----When removing the glass, incline the upper

part of the glass towards outside direction
of the door.

INSTALLATION:
Install in the reverse order of removal.

NOTE：
Do not tighten the screw before until the
glass is installed in place properly.

S-36

REMOVAL & INSTALLATON OF REAR
DOOR GLASSES

REMOVAL：
----Before removal of front door glasses, the

trim panel and waterproof film shall be
removed first following instructions.

----Pull out the inner and outer door waterproof

strips; begin the removal from the rib of the
internal side of the central door frame.

----Place the glass at the center of the door

frame. Loosen the fixing slot of the
window regulator support.

----When removing the glass, incline the upper

part of the glass towards outside direction
of the door.

Install in the reverse order of removal.

NOTE：
Do not tighten the screw before until the
glass is installed in place properly.

REMOVAL & INSTALLATON OF REAR
QUARTER GLASS

REMOVAL
----Before removal of quarter glass, the trim

panel and waterproof film shall be removed
first following instructions.

----Take out the inner and outer pressed

moldings of the door, and remove them
from the rib position of the internal side of
the central door frame.

----Loosen the bolts between the central guide

rail and inner panel of the door, and
remove the central guide rail.

----Pull the quarter glass outwards and it

should be removed easily.

INSTALLATION：
Install in the reverse order of removal.

S-37

REMOVAL & INSTALLATON OF FRONT WINDOW REGULATOR
REMOVAL：

----Before removal of front window regulator,

the trim panel and waterproof film shall be
removed first following instructions.

----Loosen six screws that secure window

regulator to the inner panel of the door as
shown in the figure.

----Disconnect the motor connector of window

regulator and take out the regulator.
Removal of window regulator is performed
separately from that of glass.

INSTALLATION：

Install in the reverse order of removal.

NOTE：

----Tightening torque for bolts or nuts of

window regulator is M=9±1N.m.

----Installation size for glass bracket is 105mm

as shown in the figure.

----Tighten the six screws of window regulator

only after the glass is fully raised till the top
and can run up and down smoothly.

----After installation and adjustment, the glass

should run up and down smoothly. Any
shaking, vibration or shock is not allowed.
The up or down movement of glass shall
be finished within 3±1S.

105

S-38