Chery B11. Manual — part 27
Driving
109
distance depends greatly on road
surface condition. ABS does not
always shorten the brake distance.
On road surfaces that have a snow
or sands for example, braking
distances may be longer. ABS does
not assure safety when the vehicle
in the front is too close, when driving
on wet condition or when you steer
too sharply. For these reasons please
drive carefully and reduce your
speed when steering.
ABS Self-Inspection
When engine is started, ABS will inspect
itself. It’s normal to hear mechanic noise
during this process.
When driving if the ABS warning
lamp lights, it indicates malfunction
of ABS. Please contact Chery Special
Service Center for service in this
case.
Important pricople
whicle makes use of
Make the braking
pedal depressed as
possible as you can
and holdit.
Turn the steering wheel ,derour..you
can keep the operational
derformance of making a turn
without exception ,no matter how
fierce the braking force is.
Driving
110
Principle of working with ABS:
1. Press on the brake pedal all the way
down and hold it.
2. Turn the steering wheel and get
around the obstacle, remain control
on the steering wheel no matter how
severe the vibration is.
Hand Brake
Pull up and engage the hand brake to
prevent the vehicle from rolling when
parking.
Do remember to engage the
parking brake before
leaving the vehicle.
When engaging the parking brake while
the engine is running, the brake lamp
lights up.
To apply parking brake, pull up the
parking brake handle.
To release the hand brake, pull the handle
up slightly, then press the release button
on the top of it and pull it down.
Parking brake acts to the rear wheels.
Hand brake lever is easier to pull up if you
pull it while pressing on the foot brake
pedal.
Power Steering
To avoid damaging the power steering
system:
Ÿ
While the engine is running, limit the
time the steering wheel is turned to
the extreme (left or right) for a few
seconds.
Ÿ
Adding steering oil, before the oil
drops below the “MIN” mark. Do
not drive the vehicle until the oil
level exceed the mark.
When power steering system fails or the
engine is shut off, steering wheel can still
be controlled, but increased effort will be
required to steer the vehicle.
If there is difficult steering or the vehicle
runs with vibration, please check the
followings:
Ÿ
tire pressure
Driving
111
Ÿ
whether the tread wear of the tires is
even.
Ÿ
whether suspension components are
loose or damaged.
Operation of Auto-shift
Auto-shift transmission in your vehicle is
a electronically- controlled transmission
device with manual-shift option.
Shift Gear Level
P = for Parking
R = for Reverse
N = for Neutral
D = for Driving
In Manual-shift mode
+ for shift to higher gear level
- for shift to lower gear level
P =Parking
At “P” position, transmission output axel
is locked and hence the driving wheels are
locked. If you leave the car without
placing the shift gear level at “P”, a
warning signal sound will be heard.
Shift to “P” only after the
vehicle has come to a full
stop.
Only when the foot brake pedal is pressed
and the ignition key is in position “ON”,
Driving
112
can the gear be shifted.
R = Reverse
Shift to “R” when you are reversing the
vehicle.
Shift to “R” only when the
vehicle has come to a full stop and
the engine is running at idle speed.
N = Neutral
Shift to “N” only when the engine is
running at idle speed or before starting the
engine. In “N” position, driving of engine
is not transmitted to the wheels.
D = Driving
Shift to “D” when driving.
Manual-shift Option
Manual-shift can be active only when the
shift gear level is in “D” position.
To shift to manual mode pull the gear
lever to the right hand side.
In manual mode, push the gear lever
towards “+” sign to shift to the next higher
gear; push the gear lever towards “-” sign
to shift to the next lower gear.
In manual mode, gear can be shifted to
higher level at any vehicle speed. But shift
to lower gear only when the vehicle slows
down to certain range of speeds.
Gear Display
When the engine is running, current gear
is displayed at the center of panel.
Gear is displayed as in following figures:
P position
R position
N position
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст