Chery B11. Manual — part 1
Introduction
5
“*” only applies to some models of Cherry
Vehicle.
Safety and Envirommental
Protection
Warning symbols used in this
manual
This symbol indicates that
this section contains relevant information
on how to avoid the possibility of personal
injury and serious damage to the vehicle
or equipment in vehicle. Please read and
comply with it.
Warning Symbols on Vehicle
It indicates that you should consult the
relevant section of this Owner’s Manual
before you take any action.
Environmental Protection
We should take our liability in
enviromental protection. To
achieve this object, please use your
vehicle and handle discarded articles for
cleaning and lubricant properly. This
manual displays all these information in
tree structure.
Protection system for safe
driving
At present, traffic accident is not
avoidable. However, advanced technology
can be utilized to reduce traffic accident.
For instance, your vehicle is equipped
with front and rear collision absorbing
area,in addition,lateral side of your vehicle
is equipped with crosswise collision
protection area.
The advanced airbags protecting system
will protect you in the event of severe
frontal impact. The safe seat can reduce
the tendency to slide under seat belt. All
protection equipment is well designed and
Introduction
6
can reduce injuries and damages.
Drive carfully and keep alert. Do not use
these protection equipments unnecessarily.
Please read the chapters
related to airbages. Any improper
use of airbags might cause injury.
Extreme danger! Do not use
rear-facing baby seat in any seat
where front airbags is installed.
Electronic device which
providing safety
In order to protect your safety, advanced
electronic control system is installed in
your vehicle.
Using portable cellular
phone with external antenna or
other electronic equipment will
produce electromagnetic field that
might cause some vehicle’s electrical
system failure. Please follow
manufacturer’s instruction.
Checking your vehicle
before us
Ÿ
Check the air-tightness of the lower
part of vehicle body including:
universal joint cover, steering wheel
cover, base plate, brake system,
clutch system and wheels
Ÿ
Check the following liquid level:
Engine coolant level
Washer fluid level
Engine oil level
Transmission oil
Power steering oil
Brake fluid level
Ÿ
Check battery’s voltage
Ÿ
Check tire pressure of each wheel
Ÿ
Check connetion and tightness of
each part, especial for transmission,
steering, brakes, suspension and
wheels.
Introduction
7
Ÿ
Check installation status of tire valve,
wheelhouse and fuse.
Ÿ
Check clean status of vehicle body,
including paint, interior decorations
and glasses.
Ÿ
Check clean status of internal room,
including seat cushion, interior trims,
rug and mat.
Ÿ
Check window washer system.
Ÿ
Check electronic equipment, switch,
display and other control system.
Ÿ
Check working status of engine,
gearbox and generator.
Ÿ
Check working status of brakes and
transmission system to see if they are
in good condition.
Ÿ
Check onboard tool kits and
document to see if they are ready for
use.
Break-in period
Due to mismacthining and misassembling,
the frictional resistance of transmission
part is always much greater in break-in
period than normal period. Proper use in
break-in period can extend service life,
increase stability and provide potential
economy. Therefore, the following
break-in rules must be complied with.
Break-in rules for the first
1000 km:
Ÿ
Do not drive at maximum speed.
Ÿ
Do not drive over 100km/h.
Ÿ
Do not use full throttle for any gear.
Break-in rules for the first
1000 km to 1500 km:
Ÿ
Increase your engine speed gradually
and drive at permitted maximum
speed
After break-in period:
The maximum speed is 6000 r/min for
short-time engine running. You must shift
up a gear when the needle of speed meter
Introduction
8
reaches red zone.
Maximum speed for each gear:
Gear 1 45 km/h
Gear 2 80 km/h
Gear 3 115 km/h
Gear 4 155 km/h
Gear 5 195 km/h
Avoid your engine running at
very high speed. Timely
shift-up is in favor of saving gasoline,
reducing engine noice and also is helpful
for protecting environment.
Do not operate your engine at very low
speed. Please shift down a gear when
engine is working strenuously.
Suggested rotational speed in manual only
applies to the engine working under
normal temperature. Do not operate at
maximum speed in any gear when engine
is cold.
New tires do not achieve their full traction
potential at the begining. Therefore,
break-in period is also necessary for new
tires. You should drive slowly with extra
caution during the first 100km.
Break-in period is also necessary for new
friction disc of the brake. During initial
200 km, the brake disc has not yet
achieved the optimum surface friction. In
this period, you can increase brake pedal
force if brake does not work as you expect.
Replacement of brake disc each time also
applies to this case.
You must screw wheel nuts to the correct
torque. The correct torque value refers to
“Technical data and specification” chapter
in this Owner Manual. You also need to
screw wheel nuts again if you ever
replaced your wheel or released your
wheel nuts after driving 800 km.
Wish you have an enjoyable and safe
driving experience with your Cherry.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст