Chery B11. Manual — part 119
Step 5: screw off the set bolts and take
out the fork arm.
Fixing steps:
1. Fix with reference to the unfixing
steps.
2. Note:
Released set bolts which are subject
①
to
yielding limit in terms of torque + angle
fixing during bolting must be replaced.
Fasten the bolts with the required
②
torque
Nine. Replacing rear wheel shock
absorber
Tool required: 15cm socket, quick
spanner, 21cm socket, short connecting
rod, torque spanner, 19cm socket
Unfixing steps:
Step 1: dismantle the wheel and jack up
the car.
Step 2: release the three set bolts above
the shock absorber.
Step 3: release the set bolts for the shock
absorber and horn.
Fixing steps:
1. Fix with reference to the unfixing
steps.
2. Note:
Released set bolts which are subject to
①
yielding limit in terms of torque + angle
fixing during bolting must be replaced.
Fasten the bolts with the required
②
torque
Ten. Fixing and unfixing of rear axle
Tools required: one set of sockets,
connecting rod, torque spanner
Unfixing steps:
Step 1: dismantle the left and right wheel
and jack up the car.
Step 2: release the middle and rear
exhaust pipes.
Step 3. release the set bolts for shock
absorbers and rocker arms on both sides.
Step 4: release the set bolts of manual
brake cable and ABS wire harness (see
Brake Assembly)
Step 5: release the set bolts for the horn
and the rocker arm.
Step 6: release the set bolts of the brake
sub-pump and displace the brake sub-
pump.
Step 7: release the set bolts for left and
right longitudinal stay bars.
Step 8: support the rear axle with the
gearbox bracket, release the set bolts for
real axle and car body and dismantle the
rear axle.
Fixing steps:
1. Fix with reference to the unfixing
steps.
2. Note:
Released set bolts which are subject to
①
yielding limit in terms of torque + angle
fixing during bolting must be replaced.
Fasten the bolts with the required
②
torque
Chery B11 Service Manual
Air Conditioner-1
Section 1 Safety Precautions for A/C System
1.
Do not handle the refrigerant in the unventilated
location or near fire.
2.
Wear a safety goggle.
3.
Take care not to let the refrigerant liquid splash onto
your skin or into your eyes.
If the refrigerant splashes into your eyes or onto your
skin,
(a) wash them with cool clean water.
WARNING:
Do not wipe your eyes or skin.
(b) appropriately clean the oil on your skin.
(c) go to a hospital immediately and consult a doctor.
4.
Do not heat the container or place it near fire.
5.
Take care to move the refrigerant container gently so
as to prevent the container from being impacted by
the sharp objects.
6.
The refrigeration system shall fill with sufficient
refrigerant during outdoor use.
If an insufficient refrigerant level is detected in the
refrigeration system, the oil lubrication will be poor and
the compressor may be damaged. Thus, sufficient
refrigerant shall be added to the refrigeration system in
order to avoid the occurrence of the conditions above.
7.
Do not open the pressure combination vacuum valve
during the course of the operation of compressor.
If the high-pressure valve is left open, the refrigerant will
flow back into the refrigeration cycle and cause the
refrigerant
container
damaged.
Thus,
only
the
low-pressure valve can be opened / closed.
8.
Take care not to let the system (with refrigerant)
overloaded.
Chery B11 Service Manual
Air Conditioner-2
Section 2 Parts and Components Location Index
1
HVAC lower case
19
Bolt mounting clip
37
Metal connecting rod 4
55
Radiator tube clamp
2
Damper 5 shaft
20
Internal cycle
regulation actuator assy.
38
Metal connecting rod 3
56
Radiator outlet sponge
3
Damper 5 sealing strip 1
21
Damper 3
39
Damper 4 sealing sponge 2
57
Drainpipe sponge
4
Damper 5
22
Damper 3 sealing strip
40
Damper 4 sealing sponge 1
58
Drainpipe assy.
5
Damper 5 sealing strip 2
23
Damper 6 shaft
41
Damper 4
59
Evaporator outlet sponge
6
Lower air outlet case
24
Damper 2
42
Damper 4 shaft
60
Expansion valve sealed cap
7
Lower air outlet sponge
25
Damper 2 sealing strip
43
Cold/Warm air distribution
bracket
61
Hexagon socket head cap screw
8
Tapping screw
26
Upper air outlet sealing sponge
1
44
Warm-air radiator
62
Evaporator lower heat insulating
mattress
9
Harness clip (white)
27
Upper air outlet sealing sponge
2
45
Temperature
regulation
actuator assy.
63
H type expansion valve
10
Metal harness clip
28
Damper 1 shaft
46
Radiator core heat insulating
mattress 1
64
Evaporator core components
11
Relay
29
Damper 2 and 3 shaft
47
Radiator core heat insulating
mattress 2
65
Rubber-hose clamp
12
Blower motor assy.
30
Wind
direction
regulation
actuator assy.
48
Metal connecting rod 2
66
Air inlet sealing sponge
13
Electronic
speed
regulation
module
31
Tapping screw2
49
Double
connecting
rod
1(white)
67
Metal connecting rod 5
14
Harness assy.
32
Double connecting rod 2(white)
50
Triple
connecting
rod
(white)
68
Damper 1
15
Upper case
33
Double connecting rod 3(white)
51
Metal connecting rod 1
69
Stud
16
Air inlet case
34
Double connecting rod 4(white)
52
Connecting rod fixing clip
70
Upper
case
circular
spongy
cushion
17
Damper 6
35
Combination
console
panel
(white)
53
Air pipe assy.
18
Damper 6 sealing strip
36
Platen
54
Radiator foam guard strip
3. STRUCT URE OF VEHICLE A/C REFRIGERAT ION SYST EM
3.0.1: ST RUCT URE OF CHERY AUTO A/C REFRIGERAT ION SYST EM
COMPRESSOR
CON DEN SER
HIGH/LOW-PRESSURE SWITCH
EVAPO RATO R A SSY.
P IPE.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст