Chery B11. Manual — part 15
Air Condition System
61
The knob is used to adjust air temperature
by 0.5
.
Ÿ
Right turn——temperature rise,
increasing 0.5
by rotating one
step.
Ÿ
Left turn-- Temperature descend,
reducing 0.5
by rotating one step.
The setting value of temperature will be
displayed on the screen.
The recommended value is 22
. Use this
knob to set temperature between 19
to
32
. It will display “LO” if temperature
is under 18
and display “HI” if
temperature is higher than 32
.
You can turn left to increase the cooling
effect while cooling system is working.
The system will be set in cold state when
in position “LO” (temperature is under
18
). The system will not be set to high
temperature state but not steady
temperature when it is in position “HI”
(temperature is higher than 32
),
The temperature showed on the screen will
be updated with the outdoor temperature
while pressing the knob. Symbol “
”
will also apprear on the screen. After three
seconds, the temperature showed on the
screen will be reset and
symbol
disappears. The temperature set value does
not change by turning knob when outdoor
temperature is showed on the screen.
4.Auto mode button
When you press this button, the control
system will adjust position of mixture vent,
AC state, blower speed and ventilation
from outside or indoor air recirculation,
according to pre-set temperature value or
outside temperature and variety of inside
temperature. The actual indoor
temperature can reach to pre-set
temperature value.
“Auto Mode” will be displayed in the
screen.
Air Condition System
62
The initial blowing mode is “floor” and
“panel” when using “AUTO” mode. You
can switch the model by pressing the
“Mode” button. Auto button and Mode
button are separated functional buttons.
“Defrosting” button work based on
windshield wiper signal, which means the
air conditioning system is working in
“defrosting” mode automatically (no state
change of wind volume), once the
windshield wiper starts.
The working state of AC compressor is
determined by pre-set temperature, the
compressor will NOT aspirate when
temperature is higher than 28
.
The system will switch to
internal-recirculation mode automatically,
when one of the following three conditions
is satisfied:
Ÿ
Air conditioning system just starts
working (compressor just start up)
Ÿ
The vehicle is moving with 10K m/h
for more than ten seconds.
Ÿ
The engine is stopped.
The system will run with the mode or
interface that the user has set up last time.
5. “OFF” Button
Switch off Air conditioning system.
The system will be shut down when
pressing this button. Screen will be shut
down as well. At the same ime, all
executing system is off.
The system will start automatically when
pressing “AUTO” button or AC button or
“Defrost” button ,even the system is off.
The system will run with the mode or
interface the user has set up last time.
7. Blowing Mode Button
The airflow model will be switched in the
following models when you press
“MODE” button each time. At the same
time, the following symbol appreas:
Ÿ
Floor, air flows mainly into the
footwell.
Air Condition System
63
Ÿ
Panel, air flows toward the upper
body.
Ÿ
Bi-level: Air flows toward both
footwell and the upper body.
7. Air Conditioner Button
Air conditioning system will start while
pressing the “AC” button. At the same
time, snowflake symbol “
” appears on
the screen.
Air conditioning system only works under
the following condition:
Ÿ
Engine is running.
Ÿ
Temperature is higher than -1
.
Ÿ
Blower is set from level 1 to level 4
When air conditioning system starts, it
will not only decrease the temperature in
vehicle but also decrease the air humidity
from outside. It makes passengers feel
comfortable and also it can avoid moisture
condensed on the window.
To achieve the best effect of cooling, all
windows must be closed when the air
conditioning system is engaged.
8. Windshield Defroster/defoger
button
This button is used to windshield
defogging. Once you press the button, it
changes air supply from inside to outside.
Air conditioning system also starts up.
All airflow flows toward the vents of rear
windshield and side window.
Windshield defroster symbol
Will appear on the display screen.
Air conditioning system economical
running
The air conditioning system will
consume engine power and
increase fule consumption. To
save energy, please do not start air
Air Condition System
64
conditioning system when unnecessary.
The interior temperature can be very high,
when vehicle is exposed under sun. Please
open door or window, it will help warm air
to go away. It is helpful for decreasing fule
consumption and enhancing cooling
effect.
Do NOT use air conditioning system, if
window is open while driving.
General Instruction
Air conditioning system will absorb
moisture and water vapour condensing
into water. It is normal phenomenon that
small watermark is found under the
vehicle, when the vehicle stops for a
while.
The heating effect depends on the
temperature of engine coolant. Therefore,
the heating system works efficiently when
engine is warm up.
To avoid windows fog over, it is suggested
that set the blower to low speed.
Do NOT allow the cold air blow to your
body.
Air conditioning system
operation instruction in the
hot wheather
1. Press “AUTO” button.
2.Press “MODE” button to select
recirculated air mode.
3. Set temperature to “LO”
4.Re-set the temperature that is pleasant
for you when temperature drops.
Suggestions:
Please keep recirculated air mode in the
hot weather. It will achieve the best
cooling performance and prevent outside
odors.
Trouble Shooting
Cooling System malfunction
Ÿ
Temperature is lower than –1
.
Ÿ
Fuse is burned out.
Check fuse and replace it when necessary.
If the problem is not related to fuse, please
shut down your air conditioning system
and let the professional technicians to
check it.
Cooling capacity decrease
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст