Chery B11. Manual — part 48
Maintenance Manual for Chery·Oriental Son
Engine Section
Valve seat working surface angle(43.5--44
° ) is a little less than valve working
surface angle(45°)
11. Timing Gears Train
凸轮轴正时轮 Camshaft timing gear
正时带张紧轮 Timing belt tensioner
张紧轮支架 Tensioner bracket
工具 Tool
自动张紧器 Automatic tensioner
左平衡轴齿带轮 Left balance axle belt gear
B 带张紧轮 B belt tensioner
曲轴平衡轴齿带轮 Crankshaft balance axle
belt gear
曲轴正时齿带轮 Crankshaft timing belt
gear
机油泵轮 Oil pump gear
右平衡轴 Right balance axle
正时齿带 Timing belt
阻尼轮 Damping gear
上平衡轴 Upper balance axle
上平衡轴齿带轮 Upper balance axle
belt gear
B 带调整轮 B belt regulating gear
曲轴 B 带轮挡片 Crankshaft B belt
gear stop plate
曲轴 B 带轮 Crankshaft B belt gear
下平衡轴 Lower balance axle
Upper Balance Axle
Belt Fitting Mark
13
Maintenance Manual for Chery·Oriental Son
Engine Section
前端盖边缺口标记 Notch around front
end cover
左 平 衡 轴 齿 带 轮 上 三 角 标 Triangle
sign on the left balance axle belt gear
前 端 盖 上 标 记 Marks on front end
cover
曲轴挡盘上缺口标记 Notch on the
crankshaft bearing disc
There is an independent transmission belt
on the upper-left balance axle. Tension
wheel B is located on the loosened side,
which is to adjust belt tension manually.
The teeth number of drive gear is 38 teeth
and the teeth number of driven gear is 19.
Please note that align the marks of
crankshaft B belt gear and front end cover
and the marks of upper-left balance axle
belt gear and front end cover
when installing left balance
axle belt gear, which is as
shown.
Timing Belt Fitting
Mark
凸轮轴齿带轮上的标记 Marks
on the crankshaft belt gear
气门罩盖上的缺口标记 Notch
on the valve cover
前端盖上的标记 Marks on the
front end cover
14
Maintenance Manual for Chery·Oriental Son
Engine Section
曲 轴 正 时 带 轮 上 的 标 记 Marks on the
crankshaft timing belt gear
机油泵齿带轮上的标记 Marks on the oil pump
belt gear
15
Maintenance Manual for Chery·Oriental Son
Engine Section
Oil Pump Gears Mark
机油泵从动齿轮 Oil pump driven gear
主 、 从 动 轮 上 的 标 记 Marks on
drive/driven gear
机油泵主动齿轮 Oil pump drive gear
Please note that align the marks of camshaft
belt gear and valve cover, the marks of
crankshaft timing belt gear and front end
cover and the marks of oil pump belt gear
and front end cover when installing timing
belt. (The 60mm-length screw drive must
be inserted into the lower balance test hole,
otherwise turn around oil pump belt gear
and then align timing mark.)
Please align the marks of
drive/driven gears when
installing oil pump gears as
shown.
16
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст