Chery Tiggo T11 LHD. Manual — part 67
Chery T11 Service Manual Electric Injection System
81
12) The engine speed increases difficultly or the engine shuts down when
acceleration
No.
Operation Step
Detection
Result
Subsequent Step
1
Place the ignition switch on the “ON” position, and apply the
failure diagnosis instrument to examine and confirm whether
there are some failure information records.
Yes
Remove
the
displayed
failure
No
Next step
2
Examine and confirm whether the air cleaner is unobstructed.
Yes
Next step
No
Replace
3
Enable the engine to operate at idle speed, and examine and
confirm whether the speed is normal during idle operation.
Yes
Next step
No
Refer to the idle
failure items to
examine and
repair
4
Enable the engine to operate at idle speed, and examine and
confirm whether the intake pressure is 35 to 55 kPa.
Yes
Next step
No
Examine and
repair
5
Enable the engine to operate at idle speed, and, after the
coolant temperature reaches the normal value, examine and
confirm whether the ignition advance angle is normal.
Yes
Next step
No
Adjust the
ignition advance
angle
6
Connect the fuel pressure gage valve, short circuit the No 30
pin and No 87 pin of the fuel pump relay to enable the fuel
pump to operate, and examine and confirm whether the fuel
pressure is approximate 350 kPa.
Yes
Next step
No
10
7
Apply the special connecting terminal to directly supply the
fuel injector 12 V voltage from the battery, and examine the
normal operation of fuel injector.
Yes
9
No
Next step
8
Rinse the fuel injector, and then reexamine the normal
operation of fuel injector.
Yes
Next step
No
Replace the fuel
injector
9
Examine and confirm whether the fuel deteriorates or contains
water
Yes
Replace fuel
No
15
10
Examine and confirm whether the fuel pressure is below 350
kPa.
Yes
Next step
No
14
11
Shut off the fuel gage valve, turn on the ignition switch again
to enable the fuel pump to operate again, and examine and
confirm whether the fuel pressure can be established.
Yes
Next step
No
13
12
Turn on the fuel gage valve, apply the fuel return immobiliser
to clip the fuel return pipe tightly so as to make it hasn’t fuel
return, and examine and confirm whether it is able to establish
Yes
Replace fuel
pressure
regulator
Chery T11 Service Manual Electric Injection System
82
the fuel pressure quickly.
No
Repair or
replace fuel
injector or fuel
pipe
13
Examine the leakage or jamming of the fuel intake pipe.
Yes
Repair or
replace the fuel
intake pipe
No
Replace fuel
pump
14
Examine the jamming or bending of the fuel return pipe
Yes
Repair or
replace the fuel
return pipe
No
Replace the fuel
pressure
regulator
15
Place the ignition switch on the “ON” position. Connect up an
adaptor between ECU and harness, and examine and confirm
whether the voltages of the output terminal of ECU’s throttle
position sensor, earth terminal, and No 4 and 20 pins (applied
for 4.5 to 5.0V sensor power supply) are normal.
Yes
Next step
No
Repair or
replace harness
16
Examine and confirm whether the ignition coil, high-voltage
wire and sparkle plug operate normally.
Yes
Replace ECU
No
Replace related
parts
Chery T11 Service Manual Electric Injection System
83
13) Slow response when acceleration
Whether the fuel meets the standard requirement and whether there are the intake pressure
sensor and throttle position sensor failures.
No.
Operation Step
Detection
Result
Subsequent
Step
1
Place the ignition switch on the “ON” position, and apply the
failure diagnosis instrument to examine and confirm whether
there are some failure information records.
Yes
Remove
the
displayed
failure
No
Next step
2
Shut down the engine, and examine and confirm whether the
air cleaner is unobstructed.
Yes
Next step
No
Replace
3
Enable the engine to operate at idle speed, and examine and
confirm whether the speed is normal during idle operation
Yes
Next step
No
Refer to the
idle failure
items to
examine and
repair
4
Enable the engine to operate at idle speed, and examine and
confirm whether the intake pressure is 35 to 55 kPa.
Yes
Next step
No
Examine and
repair
5
Place the ignition switch on the “ON” position. Connect up an
adaptor between ECU and harness, and examine and confirm
whether the voltages of the output terminal of ECU’s throttle
position sensor, earth terminal, and No 4 and 20 pins (applied
for 4.5 to 5.0V sensor power supply) are normal.
Yes
Next step
No
Repair or
replace
harness
6
Enable the engine to operate at idle speed, and, after the
coolant temperature reaches the normal value, examine and
confirm whether the ignition advance angle is normal.
Yes
Next step
No
Examine the
others
7
Connect the fuel pressure gage valve, short circuit the No 30
pin and No 87 pin of the fuel pump relay to enable the fuel
pump to operate, and examine and confirm whether the fuel
pressure is approximate 350 kPa.
Yes
Next step
No
11
8
Apply the special connecting terminal to directly supply the
fuel injector 12 V voltage from the battery, and examine the
normal operation of fuel injector.
Yes
10
No
Next step
9
Rinse the fuel injector, and then reexamine the normal
operation of fuel injector.
Yes
Next step
No
Replace the
fuel injector
10
Examine and confirm whether the fuel deteriorates or contains
water
Yes
Replace fuel
No
16
11
Examine and confirm whether the fuel pressure is below 350
kPa.
Yes
Next step
No
15
Chery T11 Service Manual Electric Injection System
84
12
Shut off the fuel gage valve, turn on the ignition switch again
to enable the fuel pump to operate again, and examine and
confirm whether the fuel pressure can be established.
Yes
Next step
No
14
13
Turn on the fuel gage valve, apply the fuel return immobiliser
to clip the fuel return pipe tightly so as to make it hasn’t fuel
return, and examine and confirm whether it is able to establish
the fuel pressure quickly.
Yes
Replace fuel
pressure
regulator
No
Repair or
replace fuel
injector or
fuel pipe
14
Examine the leakage or jamming of the fuel intake pipe.
Yes
Repair or
replace the
fuel intake
pipe
No
Replace fuel
pump
15
Examine the jamming or bending of the fuel return pipe
Yes
Repair or
replace the
fuel return
pipe
No
Replace the
fuel pressure
regulator
16
Examine and confirm whether the exhaust system and
three-way catalytic converter are jammed.
Yes
Replace or
clean
No
Replace ECU
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст