Chery Tiggo T11 LHD. Manual — part 110

4. Blowing mode knob

Turn the blowing mode knob to make
the air conditioning operate according
to the mode indicated by the mode
knob.



Foot, all output air flow to the
footwell.



Face, all output air flow to the
area flushing with the face.



Foot and Face, one part of all
output air flow to the footwell, and
the other ones flow to the face
area.



This setting is used to introduce air
and guide them to flow across the
front defroster and the conduit near to
floor simultaneously.

5. Air conditioning cooling

switch

Press the button “A/C” to make the
cooling system operate.

The cooling system can work only
when the following conditions are met:



The engine is in state of

operation.



Ambient temperature is more
than

-1

℃.



The fan switch is set to 1 to 4
position.

When the cooling system works, it not
only can reduce the indoor air
temperature of the vehicle, but also
reduce the indoor air humidity to make
passengers feel comfortable and also
prevent the vehicle window from
fogging.

To reach the optimal cooling effect, all
windows shall be closed while the
cooling system works.

Economical operation of

A/C system

The

air-conditioned

compressor will consume the

power of the engine when cooling, and
thus it makes oil-consumption
increase. In order to save energy and
reduce oil-consumption, please switch
off the A/C system when you have no
use for the air conditioning.

When the indoor air temperature of

the parked car is very high due to the
direct exposure to sunshine, it is
recommended to open the window or
door of car for a short time to make
the hot air dissipate. This helps to
improve the cooling effect and reduce
the oil-consumption.

Don’t open the A/C system when the
vehicle windows open during driving.

General Specification

The A/C system can absorb and
remove the moisture of cooling air,
and make the moisture condense into
water on the evaporator. Thus, it is full

normal that there is a handful of water
accumulation under the bottom of car
when it parks for a while.

The heating effect depends on the
temperature of engine coolant, and
thus the heating system can fully exert
its efficiency only after the engine
reaches the state of warn-up.

In order to prevent windows from
fogging, it is recommended to set the
fan to the Low-Speed position when
you drive the car at low speed.

It isn’t recommended to make the
cooling air blow to your body directly.

Troubleshooting

The cooling system

doesn’t operate



The ambient temperature may be
less than

-1

℃.



The fuse may blow.

Check the fuse and replace it, if
necessary. If the default isn’t caused
by the fuse, then the cooling system of
air conditioning shall be switched off
(to switch off the button “A/C”), and
please get to the Chery Authorized
Service Station to make your car
examined by professional technicians.

Cooling

efficiency

decreases

In case that the cooling efficiency
decreases and air volume reduces,
the system shall be shut down, and
examined by professional technicians.

Rear window and rear-

view mirror defrosting

The control switch of rear

window and rear-view mirror
defrost heater is located at the
central console of instrument
board. Press the defrost heater
switch to remove the light ice
and fog from the rear window
and rear–view mirror.

The

rear window and rear-view

mirror defrost heater can work
only after the ignition circuit
switches on. Press the electrical
heating switch to shut on/down
the heating system. After the
heater is powered on, the
indicator (operating indicator) on
the switch lights to indicate the
heater is under heating.

NOTICE:

In case that the rear windscreen is
transparent, the heater shall be
shut down to reduce the current
consumption and save fuel.

After defrosting for (15±3) minutes, or
when the ignition switch turns to OFF
position, the rear window defrosting
will shut down automatically. When the
defrosting time is less than (15±3)
minutes, please press the defrosting
switch again if you want to manually
stop the rear window defrosting.

Enable the rear window to defrost, and
also enable the heater to heat the
exterior

rear-view

mirrors

simultaneously.

If pressing this switch before the
engine starts up, the defrosting
function works, but it will stop working
after the engine starts up, and the
state of defrosting won’t be stored.

Light Control

Please observe the related traffic
regulations when the following lighting
devices are applied.

Headlamp switch

OFF – switch off the embarkation light

1

st

gear

- to light the position light,

the illuminating lamp and license light
for instruments, switches and other
parts.

2

nd

gear

- to light the passing lamp

of headlamp

Note:

The headlamp is available only after
the ignition switch is turn on. And the
headlamp will turn off automatically
when the engine starts up or after the
ignition switch is turn off.

Headlamp

lighting

change

In the case that the light switch is in
ON position, turn the handle in the
instrument panel direction, and get
across the force point and then
change to the high beam. When the
high beam of headlamp is turned on,
the high beam indicator on the
instrument panel also light. Turn the

handle in the steering wheel direction
to the original position, and resume
the low beam

。

Headlamp flash

If the headlamp is required to flash
during traveling, it is nothing but to
turn the handle in the steering wheel
direction to the force point and then
release it. Repeat this action, and the
headlamp will flash continuously.