Chery QQ6 (S21) / S12LHD. Manual — part 218
12.17 When Releasing Accelerator Pedal after Acceleration, Unsteady Idle
Speed Occurs at Instant, even Extinguishes.
Yes
Remove the failure
displayed
1
Put the ignition switch to “ON”. Use a failure
diagnostic tester to check if any failure
information record exists.
No
Next step
Yes
Next step
2
With engine off, check if air cleaner is smooth
(can not simply rely on visualization, remove
the air cleaner and then perform test drive again)
and if air intake system is chocked.
No
Replace
Yes
Next step
3
Run the engine at idle speed and check if the
engine revolution speed is normal at idle speed.
No
Repair in accordance
with
idle
speed
failure item
Yes
Next step
4
After starting successfully, check if air intake
consumption of the engine at idle speed is
around 300Kg/h (remember to check if cylinder
pressure is normal).
No
Overhaul
Yes
Next step
5
Put the ignition switch to “ON”. Check if it is
break or short circuit between 38#, 32#, 54#,
36# pins on ECU connector and 1#, 2#, 4#, 6#
pins of throttle position sensor of electronic
throttle valve body.
No
Repair or replace
Harness
Yes
Next step
6
Let engine run at idle speed, after coolant
temperature reaches normal value, then use a
diagnostic tester to check if ignition advance
angle is normal.
No
Check other part
Yes
Next step
7
Connect fuel manometer valve. Short 30# and
87# pins of fuel pump relay to make the fuel
pump run, and then check if fuel pressure is
around 400kPa.
No
11
Yes
Clear carbon deposit
8
Remove air intake hose, check if carbon deposit
or other soil (this may result in air intake system
of engine being chocked when the valve plate
closes) exists.
No
Next step
Yes
Next step
9
Clean out the fuel injector and look if it can
work correctly.
No
Replace fuel injector
Yes
Replace fuel
10
Check if fuel is deteroprated or moisture.
No
16
11
Yes
Next step
Check if the fuel pressure value is below 400
kPa.
No
15
Yes
Replace or clean
12
Check if the exhaust system and three-way
catalytic converter are jammed.
No
Replace ECU
Note: For an electric control motor with the electronic throttle body, the main actuators of its air intake
system are air flow meter and electronic throttle body. Air flow meter has very high operational reliability
and very low failure rate, while, due to particularity of road status in China and affected by operating
environment, choke is liable to occur between valve plate and valve body of the electronic throttle body,
which may obstruct air from entering the engine and result in extinguish of engine.
12.18 A/C System Failure
Yes
Next step
1
Check if there is enough coolant, if the A/C belt,
the A/C clutch and the pressure switch are in
good condition.
No
Troubleshooting
Yes
Remove the failure
displayed
2
Let engine run at idle speed and turn on A/C
switch. Enter A/C self diagnosis mode to check
the A/C system for failure.
No
Next step
Yes
Next step
3
Turn on the A/C switch and connect an adaptor
between ECU and harness. Measure 75# pin
(A/C switch) of ECU and see if there are input
signals on it.
No
Check the harness
Yes
Replace or repair the
harness
4
If this vehicle adopts low level control, check if
the air condition is working still even though it
is turned off.
No
Next step
Yes
Repair
the
A/C
replay and harness
5
Check if there is low level output at ECU pin
No.69 (connect to the ground of pull in winding
of A/C relay).
No
Replace ECU
Note: Different from the controlling means of other models, the A/C control system of A21 adopts the
automatic A/C and uses double-pressure switch to control incorporation of the A/C system and the fan
after A/C starts up.
13. Safety Precautions for System Maintenance
13.1 Safety Precautions for Diagnosis and Maintenance of Gasoline
Injection Electronic Control System
(1) Disassembly and assembly requirements for electronic control unit (ECU):
Controllers shall be removed before welding or paint-baking;
When disassembling and installing the controller, be sure to set ignition switch to
CLOSE position and disconnect the battery with the system for fear to damage the
engine control unit during disassembly and installation.
Power supply wires shall not be removed from battery when engine is in operation or
electric system is in use;
Do not use such heavy current equipment as charger etc. to start the engine by direct
bridging;
Note that the ambient temperature for the controller should not exceed 80 .
℃
(2) Requirements for cleanness: the following rules should be observed for any
operation on oil-supply system and oil-injection system:
The parts removed should be place at a clean site and covered properly; do not use the
cloth (cotton cloth and gauze) with falling off fibre;
(3) Connect and disconnect the connectors of all sorts of harnesses and the connectors
of failure diagnosis testers only after the ignition switch is turned off.
When measuring mains voltage or ground wire grounding of the electronic control
system, be sure to check if the connection order and mode are correct;
Disconnect power cord or ground wire of battery from the system and disconnect
harness connector of ECU; both operation modes above may cause loss of information
about diagnosis and self-study stored in ECU (the retention time of information after the
ECU installed is power off depends on the model).
(4) Attentions during maintenance of fuel feed system (fuel feed line, fuel pump
and fuel injection system):
Disassembly or installation of oil pump on the tank full of oil or partly full of oil,
please note:
Before operation, get material ready near the fuel tank opening for absorption of heavy
discharging fuel, so that, the fuel discharged can be duly absorbed;
Avoid skin from direct contact with gasoline as best as you can;
Before loosening a connection part, thoroughly clean this part and the area around the
connecting pieces;
Dishcloth shall be placed around the connecting part for avoide oil-spraying;
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст