Chery QQ6 (S21) / S12LHD. Manual — part 106
11. The Steps for Implementation of Failure Diagnosis According to
Failure Information Records
11.1 Electronic Throttle Failure
Failure codes: P012, P0122, P0123, P022, P0222, P0223, P1336, P154, P1558, P1559, P1564,
P1565, P1568, P1579, P1604
No.
Operating steps
Result
Follow up steps
1
Put the ignition switch to “ON”.
Next step
Yes
Next step
2
Pull out the joint of throttle position sensor on
harness; use a multimeter to check if the
magnitude of voltage between its 3# and 5# pins
is around 12V and if a 5V voltage is present
between 6# and 2# pins.
No
5
Yes
Next step
3
Use a multimeter to check if the resistance
values between 1#, 4# and 6# pins of the sensor
are between 0.5kΩ and 1.6kΩ.
No
Replace the sensor
Yes
Replace the sensor
4
Meanwhile, use a multimeter to check if it is
break or short circuit between 1#, 4# and 6#
pins of throttle position sensor and ECU38#,
54#, 36#; or, turn blade of the throttle to observe
if its resistance value jumps and if the resistance
values between 1#, 4# and 6# change
accordingly with rotation of throttle.
No
Replace ECU
Yes
Repair or replace
wire harness
5
Connect an adaptor between ECU and harness,
use a multimeter respectively check if it is break
or short circuit between 1#, 2#, 6# and 4# pins
of the sensor and 10#, 32#, 36# and 54# pins of
ECU joint.
No
Replace ECU
Note: This auto adopts the electronic throttle body and has cancelled former step motor,
and the functions that were accomplished by the stop motor on a common throttle body
are now completely accomplished by the throttle driving motor. The electronic throttle
can not be repaired and failure rate of the throttle body is very low, if damaged,
replacing the assembly is the only choice to deal with the problem.
Special attention: The electronic throttle body can not be disassembled and repaired at
service station; in addition, after replacing electronic throttle body, be sure to let it carry
out self-study; otherwise, unsteady working at idle speed of engine may occur. See also
the section about electronic throttle for detailed study scheme. Maintenance of the
throttle body is analogous to that of the common valve body.
11.2 Knock Sensor failure
Failure codes: P0324, P0327, P0328
No.
Operating steps
Result
Follow up steps
1
Close the ignition switch, and the engine stops.
Next step
Yes
Next step
2
Pull out the joint of knock sensor on harness, use a
multimeter to check if both resistance values
between 1# and 2# pins and between 1# pin and
shielded wire (sensor shield) pin of knock sensor
are more than 1MΩ.
No
Replace with a new
sensor
Yes
Next step
3
Knock on the edge of knock sensor with a small
hammer and check with multimeter if there is
communicating signal output between sensor pin
1# and 2#.
No
Replace the sensor
4
Turn on the ignition switch but do not start the
engine.
Next step
Yes
Repair or replace
wires
5
Connect an adaptor between ECU and harness, use
a multimeter respectively check if it is break or
short circuit between 19#, 20# pins of ECU and
1#, 2# pins of sensor joint.
No
Replace ECU
Note: Generally, knock sensor is not liable to damage. When disassembling and installing the knock
sensor, be careful not to leave dirt on the contact surface of the sensor and the engine body and do
not add any gasket. If the sensor is damaged, it will have an comparatively great effect on
economical efficiency and emission of the engine. After the knock sensor is damaged, the electric
control system of the engine will lock ignition advance angle of the engine at a fixed ignition angle,
so, the acceleration performance of the engine will fall and economical efficiency and emission of
the engine will also be greatly affected.
11.3 Air Pressure Sensor Failure
Failure codes: P0102, P0103, P0112, P0113
No.
Operating steps
Result
Follow up steps
1
Put the ignition switch to “ON”.
Next step
Yes
4
2
Pull out joint of intake air pressure sensor on
harness; use a multimeter to check if a 5V
voltage is present between 2# and 3# pins of the
joint.
No
Next step
Yes
Repair or replace
harness
3
Between ECU and harness, use a multimeter to
respectively check if it is break or short circuit
between 42# and 33# pins of ECU and 1#, 2#,
3#, 4# pins of sensor joint.
No
Next step
4
Replace the intake air temperature pressure
sensor.
Next step
Note: In case the sensor shorts to 5V or 12V power supply or ground, the engine may not start up or
stop running.
11.4 Front Oxygen Sensor Failure
Failure codes: P0130, P0131, P0132, P0134, P0135
No.
Operating steps
Result
Follow up steps
1
Put the ignition switch to “ON”.
Next step
Yes
Next step
2
Pull off the connector of harness of oxygen sensor.
Check the voltage between pin 1# (+) and 2# (-)
with multimeter and detect if it is around 12V.
No
4
Yes
Replace ECU
3
Use a multimeter to check if the resistance value
between 1# and 2# pins of the oxygen sensor is
between 2Ω and 5Ω at 23
.
℃
No
Replace the sensor
Yes
Next step
4
Check if heating circuit of the oxygen sensor is
normal.
No
Check the circuit
Yes
Repair or replace
harness
5
Check if it is short circuit or break circuit between
the pin 2# of oxygen sensor and main relay 87#
pin and between the sensor connector 1# pin and
ECU 1# pin with multimeter.
No
Next step
6
Connect the oxygen sensor connector of harness
and use neutral. Start the engine and leave it at
idle speed until its coolant temperature reaches to
the normal value.
Next step
Yes
Next step
7
Pull off the oxygen sensor connector of harness.
Check the battery output voltage between pin 3#
(+) and pin 4# (-) of the sensor with multimeter
and detect if it is from 0.1 to 0.9V (after the
engine warms up).
No
Replace the sensor
Yes
Repair or replace
harness
8
Connect the adaptor between ECU and harness.
Check if it is short circuit or break circuit between
the pin 36# and pin 13# of ECU and the sensor
connector pin 3# and pin 4# respectively with
multimeter.
No
Replace ECU
9
Plug in the oxygen sensor connector of harness
and use neutral. Start the engine and leave it at
idle speed until its coolant temperature reaches to
the normal value.
Next step
Yes
Next step
10
Connect special diagnostic tester for Chery to read
part of data stream of the engine, and then observe
if part of data stream of the sensor fluctuates
between 100mv and 900mv.
No
Replace the sensor
11
Start the engine and let it run at idle speed until
coolant temperature reaches normal value.
Next step
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст