Engine 2.0 (Chery Fora, A21). Manual — part 7
CHERY A21 SERVICE MANUAL
MECHANISM OF 2.0NALC ENGINE
25
f:
Examine the protruding capacity of
valve stem.
And Examine the protruding high of valve
stem with vernier caliper.
(See picture)
Standard Value
(mm)
Protruding Capacity
Of Intake Valve
stem
47.5
Protruding Capacity
Of Exhaust Valve
stem
47.5
5)
Examine the axial clearance of camshaft.
Replace the camshaft if the value of axial
clearance exceeds the normal value.
Standard
Value
Intake camshaft
0.015—0.02
Exhaust camshaft
0.015—0.02
Top of Valve Stem
Protruding High of Valve Stem
Seat of Valve Spring
CHERY A21 SERVICE MANUAL
MECHANISM OF 2.0NALC ENGINE
26
6)
Examine the planeness of cylinder
a:
Clear the lower surface of cylinder head.
b:
With the help of ruler and feeler gauge,
check whether the lower surface of
cylinder head is warped.(Measure it in
the sequence of A, C, D, E, F, G in the
picture)
Standard
Value
Cylinder head planeness
0.04
CHERY A21 SERVICE MANUAL
MECHANISM OF 2.0NALC ENGINE
27
C:
Revise it if the planeness exceeds, and
replace when it exceeds the limit value.
The permitted maximum abrading thickness
between cylinder block and cylinder head is:
2.2.3
Installation
The installing steps are reverse to those for
removal.
Note:
1)
Dismantle valve springs into groups.
The 1st and 4th cylinders are in one
group and the 2nd and 3rd ones are in
the other group. Then put the piston to
the upper point of 1st and 4th cylinders
in order to dismantle the valve spring of
1st and 4th cylinders, replace their valve
oil seal and mount the spring
immediately. And put the piston to the
upper point of 2nd and 3rd cylinders in
order to replace the other valve oil seal.
Those steps prevent from that the valve
falls into cylinder and the unanticipated
trouble occurs.
2)
Wipe the engine transmission oil on the
opening of oil seal when mounting the
valve oil seal.
3)
Fasten the cylinder bolt as the following
process.
A:
Smear some oil on the top and root of
bolt.
B:
Fasten to 40±5NM in sequence.
C:
Fasten 90±5 degree clockwise.
D:
Fasten 90±5 degree clockwise.
2.3 Replace thermostat
2.3.1 Structural
diagram
8
4
1
5
9
7
3
2
6
10
CHERY A21 SERVICE MANUAL
MECHANISM OF 2.0NALC ENGINE
28
2.3.2 Needed tools and auxiliary materials
Hatch clamp,10# sleeve, ratchet wheel and wrench
2.3.3 Removal
1) Loosen the clamp of thermostat water exhaust pipe with hatch clamp to release the
coolant.
Note: Do it after the temperature decreased to prevent scald.
2) Remove the 4 bolts of thermostat cover with 10# sleeve wrench.
3) Take out the thermostat.
2.3.4 Inspection
Put the thermostat in the boiling water and use it with thermometer. Then observe the
temperatures when the thermostat is turning on and fully opened.
Temperature
value
Regular unlocking temperature
87
fully opened temperature
104
Replace the new thermostat if the measured value is abnormal.
2.3.5 Installation
The installing steps are reverse to those for removal.
Note: Fill in the engine coolant with fixed quantity after installation.
1
2
3
4
5
6
1. Pad—Thermostat Seat
2. Thermostat Seat
3. Hexagonal Flange Bolt
4. Thermostat Assembly
5. Hexagonal Flange Bolt
6. Cover—Thermostat Seat
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст