Subaru Ascent (2022 year). Manual in english — page 12
(185,1)
the ABS may be considered normal.
.
The warning light illuminates when
the ignition switch is turned to the “ON”
position and turns off approximately 2
seconds after the engine has started.
.
The warning light illuminates right
after the engine is started but turns off
immediately, remaining off.
.
The warning light remains illumi-
nated after the engine has been started,
but it turns off while driving.
.
The warning light illuminates during
driving, but it turns off immediately and
remains off.
When driving with an insufficient battery
voltage, such as when the engine is jump
started, the ABS warning light may illumi-
nate. This is due to the low battery voltage
and does not indicate a malfunction. When
the battery becomes fully charged, the
light will turn off.
&
Brake system warn-
ing light
This light illuminates with the parking
brake applied while the ignition switch is
in the “ON” position. It turns off when the
parking brake is fully released.
WARNING
.
Driving with the brake system
warning light on is dangerous.
This indicates your brake system
may not be working properly. If
the light remains illuminated,
have the brakes inspected by a
SUBARU dealer immediately.
.
If at all in doubt about whether the
brakes are operating properly, do
not drive the vehicle. Have your
vehicle towed to the nearest
SUBARU dealer for repair.
The brake system warning light has the
following functions.
!
Brake fluid level warning
This light illuminates when the brake fluid
level has dropped to near the “MIN” level of
the brake fluid reservoir with the ignition
switch in the “ON” position and with the
parking brake fully released.
If the brake system warning light should
illuminate while driving (with the parking
brake fully released and with the ignition
switch positioned in “ON”), it could be an
indication of leaking of brake fluid or worn
brake pads. If this occurs, immediately
stop the vehicle at the nearest safe
location and check the brake fluid level. If
the fluid level is below the “MIN” mark in
the reservoir, do not drive the vehicle.
Have the vehicle towed to the nearest
SUBARU dealer for repair.
!
Electronic Brake Force Distribution
(EBD) system warning
If the warning light remains on even though
the parking brake is released, the brake
fluid level may be low or there could be a
problem with the EBD system. Park the
vehicle in a safe place immediately and
contact a SUBARU dealer.
!
Vacuum pressure system warning
The brake system warning light “
/
”
will illuminate when the vacuum pressure
sensor is malfunctioning or brake booster
pressure is decreasing.
If the brake warning light continues to
illuminate for several minutes after starting
the engine, there may be a malfunction in
the vacuum system. In this case, drive the
vehicle carefully and have the system
inspected by a SUBARU dealer.
&
Electronic parking
brake indicator light
!
Parking brake indicator
The light illuminates with the parking brake
applied while the ignition switch is in the
“ON” position. It turns off when the parking
brake is fully released.
– CONTINUED –
Warning and indicator
183
3
Instruments
and
controls
(186,1)
!
Electronic parking brake system
warning
WARNING
.
When you release the electronic
parking brake while the engine is
running, the electronic parking
brake indicator light will turn off.
However, if the light still illumi-
nates, stop the vehicle in a safe
place immediately and have the
system inspected by a SUBARU
dealer.
.
If at all in doubt about whether the
brakes are operating properly, do
not drive the vehicle. Have your
vehicle towed to the nearest
SUBARU dealer for repair.
.
If the electronic parking brake
indicator light flashes, the elec-
tronic parking brake system may
be malfunctioning. Immediately
stop your vehicle in a safe loca-
tion, use tire stops under the tires
to prevent the vehicle from mov-
ing and contact your SUBARU
dealer. For details, refer to “Elec-
tronic parking brake”
NOTE
.
When the ignition switch is turned to
the “LOCK”/“OFF” position with the
electronic parking brake applied, the
electronic parking brake indicator light
remains illuminated for approximately
30 seconds and then turns off.
.
When the electronic parking brake
switch is pulled to apply the electronic
parking brake while the ignition switch
is in the “LOCK”/“OFF” position, the
electronic parking brake indicator light
illuminates, remains illuminated for
approximately 30 seconds and then
turns off.
.
Even if the electronic parking brake
indicator light flashes, if the warning
light behavior is as described in the
following examples, the electronic
parking brake system is not malfunc-
tioning.
– The indicator light turns off when
the electronic parking brake is re-
leased.
.
The electronic parking brake indica-
tor light may flash immediately after the
engine is started. However, it is not
malfunctioning if the indicator light
turns off after the electronic parking
brake is released.
.
The electronic parking brake indica-
tor light may flash after the electronic
parking brake is frequently applied and
released. However, the electronic park-
ing brake system is not malfunctioning
if the light turns off for a short period of
time.
The electronic parking brake indicator light
flashes when the electronic parking brake
system is malfunctioning. If the indicator
light flashes, promptly park in a safe
location as soon as possible and contact
your SUBARU dealer.
The electronic parking brake indicator light
remains illuminated when the parking
brake cannot be released even if the
parking brake switch is pushed. For de-
tails, refer to “Electronic parking brake”
!
Parking brake apply inhibit warn-
ing
The electronic parking brake indicator light
flashes for 10 seconds and a chirp sound
will be heard if the parking brake switch is
operated when the parking brake cannot
be applied.
!
Frequent operation warning
The electronic parking brake indicator light
flashes for 10 seconds and a chirp sound
will be heard if the parking brake switch is
operated too frequently. In this case, the
operation of the parking brake switch is
Warning and indicator
184
(187,1)
restricted to protect the electronic parking
brake system.
NOTE
Wait until the indicator light turns off.
&
Auto Vehicle Hold ON
indicator light
CAUTION
If the Auto Vehicle Hold ON indicator
light does not illuminate even when
the Auto Vehicle Hold switch is
pressed to activate the Auto Vehicle
Hold function, the electronic parking
brake system may be malfunction-
ing.
This indicator light illuminates when the
Auto Vehicle Hold is activated. For details,
refer to “Auto Vehicle Hold function”
&
Auto Vehicle Hold op-
eration indicator light
This indicator light illuminates while the
vehicle is stopped by the Auto Vehicle Hold
function. For details, refer to “Auto Vehicle
Hold function”
&
Low fuel warning light
The low fuel warning light illuminates when
the tank is nearly empty, at approximately
2.6 US gal (10.0 liters, 2.2 Imp gal). It only
operates when the ignition switch is in the
“ON” position.
CAUTION
Promptly put fuel in the tank when-
ever the low fuel warning light
illuminates. Engine misfires as a
result of an empty tank could cause
damage to the engine.
&
Door open warning light
The warning light illuminates if any door or
the rear gate is not fully closed. This
function is effective even if the ignition
switch is in the “LOCK”/“OFF” or “ACC”
position, or the key is removed from the
ignition switch.
For some models, only the open doors are
indicated by the warning lights.
Always make sure this light is not illumi-
nated before you start to drive.
&
All-Wheel Drive warn-
ing light
This light blinks if the vehicle is driven with
tires of differing diameters fitted on the
wheels or with an excessively low air
pressure in any of the tires.
WARNING
If the AWD warning light flashes,
promptly park in a safe location then
check whether all four tires are the
same diameter and whether any of
the tires has a puncture or has lost
air pressure for some other reason.
Continuing to drive with the AWD
warning light flashing can lead to
powertrain damage.
NOTE
If the temporary spare tire is used, the
AWD warning light may flash. Use of the
temporary spare tire should therefore
be restricted to the minimum time
necessary. Replace the temporary
spare tire with a conventional tire as
soon as possible.
– CONTINUED –
Warning and indicator
185
3
Instruments
and
controls
(188,1)
&
Power steering warning
light
While the engine is running, this warning
light illuminates when a malfunction has
been detected in the electric power steer-
ing system.
CAUTION
When the power steering warning
light is illuminated, there may be
more resistance when the steering
wheel is operated. Drive carefully to
the nearest SUBARU dealer and
have the vehicle inspected immedi-
ately.
NOTE
If the steering wheel is operated in the
following ways, the power steering
control system may temporarily limit
the power assist in order to prevent the
system components, such as the con-
trol computer and drive motor, from
overheating.
.
The steering wheel is operated fre-
quently and turned sharply while the
vehicle is maneuvered at extremely low
speeds, such as while frequently turn-
ing the steering wheel during parallel
parking.
.
The steering wheel remains in the
fully turned position for a long period of
time.
At this time, there will be more resis-
tance when steering. However this is
not a malfunction. Normal steering
force will be restored after the steering
wheel is not operated for a while and
the power steering control system has
an opportunity to cool down. However,
if the power steering is operated in a
non-standard way which causes power
assist limitation to occur too frequently,
that may result in a malfunction of the
power steering control system.
&
Vehicle Dynamics Con-
trol warning light/Vehi-
cle Dynamics Control
operation indicator
light
!
Vehicle Dynamics Control warning
light
CAUTION
The Vehicle Dynamics Control sys-
tem provides its ABS control
through the electrical circuit of the
ABS. Accordingly, if the ABS is
inoperative, the Vehicle Dynamics
Control system becomes unable to
provide ABS control. As a result, the
Vehicle Dynamics Control system
also becomes inoperative, causing
the warning light to illuminate.
Although both the Vehicle Dynamics
Control system and ABS are inop-
erative in this case, the ordinary
functions of the brake system are
still available. You will be safe while
driving with this condition, but drive
carefully and have your vehicle
checked at a SUBARU dealer as
soon as possible.
NOTE
.
If the electrical circuit of the Vehicle
Dynamics Control system itself mal-
functions, the warning light only illumi-
nates. At this time, the ABS (Anti-lock
Brake System) remains fully opera-
tional.
.
The warning light illuminates when
the electronic control system of the
ABS/Vehicle Dynamics Control system
malfunctions.
.
The Vehicle Dynamics Control warn-
ing light, ABS warning light, and brake
system warning light illuminate simul-
taneously if the EBD system malfunc-
tions. For further details of the EBD
Warning and indicator
186
(189,1)
system malfunction warning, refer to
“Electronic Brake Force Distribution
(EBD) system warning”
The Vehicle Dynamics Control system is
probably inoperative under any of the
following conditions. Have your vehicle
checked at a SUBARU dealer immedi-
ately.
.
The warning light does not illuminate
when the ignition switch is turned to the
“ON” position.
.
The warning light illuminates while the
vehicle is running.
NOTE
If the warning light behavior is as
described in the following examples,
the Vehicle Dynamics Control system
may be considered normal.
.
The warning light illuminates when
the ignition switch is turned to the “ON”
position and turns off approximately 2
seconds after the engine has started.
.
The warning light illuminates right
after the engine is started but turns off
immediately, remaining off.
.
The warning light illuminates after
the engine has started and turns off
while the vehicle is subsequently being
driven.
.
The warning light illuminates during
driving, but it turns off immediately and
remains off.
.
The warning light illuminates when
the engine has stalled and continues to
illuminate after the engine has been
restarted. However, it will turn off once
the vehicle starts moving.
!
Vehicle Dynamics Control operation
indicator light
The indicator light flashes during activation
of the skid suppression function and during
activation of the traction control function.
NOTE
.
The light may remain illuminated for
a short period of time after the engine
has been started, especially in cold
weather. This does not indicate the
existence of a problem. The light
should turn off as soon as the engine
has warmed up.
.
The indicator light illuminates when
the engine has developed a problem
and the CHECK ENGINE warning light/
malfunction indicator light is on.
The Vehicle Dynamics Control system is
probably malfunctioning under the follow-
ing condition. Have your vehicle checked
at a SUBARU dealer as soon as possible.
.
The light does not turn off even after the
lapse of several minutes (the engine has
warmed up) after the engine has started.
&
Vehicle Dynamics Con-
trol OFF indicator light
The light illuminates when the Vehicle
Dynamics Control OFF switch is pressed
to deactivate the Vehicle Dynamics Con-
trol system.
The Vehicle Dynamics Control system is
probably malfunctioning under any of the
following conditions. Have your vehicle
checked at a SUBARU dealer immedi-
ately.
.
The light does not illuminate when the
ignition switch is turned to the “ON”
position.
.
The light does not turn off even once
several seconds have elapsed after the
ignition switch has been turned to the “ON”
position.
– CONTINUED –
Warning and indicator
187
3
Instruments
and
controls
(190,1)
&
Warning chimes and
warning indicator of the
keyless access with
push-button start sys-
tem (if equipped)
Access key warning indicator
The keyless access with push-button start
system sounds a warning chime and
flashes the access key warning indicator
on the combination meter in order to
minimize improper operations and help
protect your vehicle from theft.
When the warning chime sounds and/or
the warning indicator flashes, take the
appropriate action.
WARNING
Never drive the vehicle if the indica-
tor on the push-button ignition
switch is flashing in green when
starting the engine. This indicates
the status that the steering wheel is
not released and could result in an
accident involving serious injury or
death.
CAUTION
.
When starting the engine again
after the operation indicator on
the push-button ignition switch
flashes in green, if the operation
indicator is still flashing in green,
there could be a steering lock
m a l f u n c t i o n . C o n t a c t y o u r
SUBARU dealer as soon as pos-
sible.
.
When the operation indicator on
the push-button ignition switch
flashes in orange, contact a
SUBARU dealer immediately.
NOTE
.
Even when the access key fob is
within the operating ranges inside the
vehicle, the access key warning for
engine start may be provided depend-
ing on the status of the access key fob
and the environmental conditions.
.
When the access key fob is taken out
of the vehicle through an open window,
the access key fob takeout warning or
passenger access key fob takeout
warning will not be provided.
!
List of warnings
CAUTION
When any of the following warnings
occurs even if the access key warn-
ing indicator does not appear, take
the appropriate action.
Warning and indicator
188
(191,1)
Inside warning
chime
Outside warning
chime
Operation indicator
on push-button igni-
tion switch
Status
Action
Ding, ding ...
(intermittent)
—
—
The driver’s door was opened while the
push-button ignition switch is “ACC”
(when the select lever is in the “P”
position).
Switch the push-button ignition switch to
“OFF”, or close the driver’s door.
When exiting the vehicle, be sure to
switch the push-button ignition switch to
“OFF”.
The push-button ignition switch was
switched to “OFF” while the driver’s door
is open.
Close the driver’s door.
Ding
Short beep
(2 seconds)
—
Lockout warning:
An attempt was made to lock all doors
using the power door locking switch or
access key fob while the access key fob is
left inside the vehicle. For details, refer to
“
Key lock-in prevention function”
Take out the access key fob from the
vehicle, and lock the doors.
The doors cannot be locked while the
access key fob is inside the vehicle.
A chirp sound will be heard, and all doors
will be unlocked.
—
Short beep
(2 seconds)
—
Access key fob lock-in warning:
The door lock sensor was touched while
the push-button ignition switch is “OFF”
and the access key fob is inside the
vehicle.
Take out the access key fob from the
vehicle, and lock the doors.
If the access key fob is inside the vehicle,
the doors cannot be locked.
—
Beep, beep, beep,
beep, beep
(5 times)
—
Door ajar warning:
The door lock sensor is touched while the
ignition switch is in the “OFF” position and
one of the doors including the rear gate is
opened.
Close the doors securely and lock them.
If one of the doors including the rear gate
is opened, the doors cannot be locked.
Ding
Long beep
(60 seconds max.)
—
Power warning:
The door lock sensor was touched while
carrying the access key fob, the push-
button ignition switch is in a position other
than “OFF” (when the select lever is in the
“P” position).
Return the access key fob inside the
vehicle, or switch the push-button ignition
switch to “OFF”.
If the push-button ignition switch is not
switched to “OFF”, the doors cannot be
locked.
Ding, ding ...
(7 seconds)
—
—
Access key warning:
The vehicle was driven while the access
key fob is not inside the vehicle.
Carry the access key fob, and drive the
vehicle.
– CONTINUED –
Warning and indicator
189
3
Instruments
and
controls
(192,1)
Inside warning
chime
Outside warning
chime
Operation indicator
on push-button igni-
tion switch
Status
Action
Ding
—
—
Access key warning for engine start:
The push-button ignition switch was
pressed while the access key fob is not
inside the vehicle.
Carry the access key fob, and press the
push-button ignition switch.
Ding
Beep, beep, beep
(3 times)
—
Access key takeout warning:
The driver exited the vehicle with the
access key fob and closed the driver’s
door while the push-button ignition switch
is in a position other than “OFF” (when the
select lever is in the “P” position).
Switch the push-button ignition switch to
“OFF”, and get out of the vehicle.
Ding
Beep, beep, beep
(3 times)
—
Passenger access key takeout warn-
ing:
A fellow passenger exited the vehicle with
the access key fob and closed a door
other than the driver’s door while the
push-button ignition switch is in a position
other than “OFF”.
Return the access key fob to inside the
vehicle, or switch the push-button ignition
switch to “OFF”.
Long beep
(continuous)
Long beep
(continuous)
—
Access key takeout without P position
warning:
The driver exited the vehicle with the
access key fob and closed the driver’s
door while the push-button ignition switch
is in a position other than “OFF” and the
select lever is in a position other than the
“P” position.
Shift the select lever to the “P” position,
switch the push-button ignition switch to
“OFF” and exit the vehicle.
Long beep
(continuous)
—
—
Select lever position warning:
The engine is turned off by pressing the
push-button ignition switch and the select
lever is in a position other than the “P”
position.
Start the engine, shift the select lever to
the “P” position, switch the push-button
ignition switch to “OFF” and exit the
vehicle.
Warning and indicator
190
(193,1)
Inside warning
chime
Outside warning
chime
Operation indicator
on push-button igni-
tion switch
Status
Action
Long beep
(continuous)
—
—
Select lever position warning:
The driver’s door was opened while the
push-button ignition switch is in a position
other than “OFF” and the select lever is in
a position other than the “P” position.
Shift the select lever to the “P” position,
switch the push-button ignition switch to
“OFF” and exit the vehicle.
Ding
—
—
The battery of the access key fob is low.
Replace the battery of the access key fob.
Ding
—
Flashes in green
(15 seconds max.)
Steering lock warning:
The engine start procedure was per-
formed, but the steering is still locked.
While turning the steering wheel right and
left lightly, depress the brake pedal and
press the push-button ignition switch.
Ding
—
Flashes in orange
(15 seconds max.)
System malfunction warning:
A malfunction was detected in the power
system or steering lock.
Contact a SUBARU dealer immediately
and have the vehicle inspected.
– CONTINUED –
Warning and indicator
191
3
Instruments
and
controls
(194,1)
&
Security indicator light
This indicator light shows the status of the
alarm system. It also indicates operation of
the immobilizer system.
!
Alarm system
It blinks to show the driver the operational
status of the alarm system. For detailed
information, refer to “Alarm system”
!
Immobilizer system
The security indicator light starts blinking
in the following conditions.
For models with “keyless access with
push-button start system”:
.
Immediately after the push-button igni-
tion switch is turned to the “OFF” position.
.
Immediately after the driver’s door is
opened or closed when all of the following
conditions are met.
– The push-button ignition switch is in
the “ON” or “ACC” position.
– The engine is not running.
In the event that an unauthorized key is
used (for example, the key is unregistered
or the ID code does not match), the power
is not switched to “ON” and the security
indicator light continues blinking.
For models without “keyless access
with push-button start system”:
.
Immediately after the key is pulled out.
.
Approximately 60 seconds after the
ignition switch is turned from the “ON”
position to the “ACC” or “LOCK” position.
If the indicator light does not blink in the
above conditions, it may indicate that
immobilizer system may be malfunction-
ing. Contact your nearest SUBARU dealer
immediately.
In the event that an unauthorized key (for
example, an unauthorized duplicate) is
used to start the engine, the security
indicator light illuminates. For details about
the immobilizer system, refer to “Immobi-
lizer”
NOTE
.
The security indicator light remains
off in the following conditions. It means
that the matching of the ID code is
completed and the immobilizer system
is deactivated, and it does not indicate
a malfunction.
Models with “keyless access with
push-button start system”:
– While the engine is running.
– The push-button ignition switch
has been turned to the “ON” or
“ACC” position and the driver’s
door has not been opened or
closed.
Models without “keyless access
with push-button start system”:
– While the engine is running.
– When the ignition switch is in the
“ON” position.
– For approximately 60 seconds
after the ignition switch is turned
from the “ON” position to the “ACC”
or “LOCK” position.
.
Even if a malfunction occurs, such
as the security indicator light flashes
irregularly, it will not affect the func-
tionality of the immobilizer system.
Warning and indicator
192
(195,1)
&
Select lever/gear position in-
dicator
1)
Upshift indicator
2)
Downshift indicator
3)
Select lever/gear position indicator
This indicator shows the position of the
select lever.
When the manual mode is selected, the
gear position indicator (which shows the
current gear selection) and the upshift/
downshift indicator light up. Refer to
“Continuously variable transmission”
&
Turn signal indicator
lights
These lights show the operation of the turn
signal or lane change signal.
If the indicator lights do not blink or blink
rapidly, the turn signal bulb may be burned
out. Replace the bulb as soon as possible.
Refer to “Replacing bulbs”
&
High beam indicator
light
This light shows that the headlights are in
the high beam mode.
This indicator light also illuminates when
the headlight flasher is operated.
&
High beam assist indi-
cator light
This light illuminates when the high beam
assist function is activated. For details
about the high beam assist function, refer
to “High beam assist function”
&
Automatic headlight
beam leveler warning
light
This light illuminates when the automatic
headlight beam leveler does not operate
normally.
If this light illuminates during driving, have
your vehicle inspected at your SUBARU
dealer.
&
LED headlight warning
light
This light illuminates if the LED headlights
malfunction. Have your vehicle inspected
at a SUBARU dealer as soon as possible.
&
Steering Responsive
Headlight warning light/
Steering Responsive
Headlight OFF indicator
light
This light illuminates when the Steering
Responsive Headlight is turned off. Also,
the light flashes when a malfunction
occurs in the Steering Responsive Head-
light. Refer to “Steering Responsive Head-
light (SRH)”
– CONTINUED –
Warning and indicator
193
3
Instruments
and
controls
(196,1)
&
Front fog light indicator
light (if equipped)
This indicator light illuminates while the
front fog lights are illuminated.
&
Headlight indicator
light
This indicator light illuminates under the
following conditions.
.
The light switch is turned to the “
” or
“
” position.
.
The light control switch is in the “AUTO”
position and the headlights illuminate
automatically.
&
X-MODE indicator
This indicator appears while X-MODE is
activated. It will disappear when X-MODE
is deactivated. Refer to “To activate/deac-
tivate X-MODE”
&
Hill descent control in-
dicator
This indicator appears while the hill des-
cent control function is in standby. It will
flash while the hill descent control function
is operating. It will disappear when the hill
descent control function is not available.
Refer to “Hill descent control function”
&
BSD/RCTA warning in-
dicator (if equipped)
This warning indicator appears when the
BSD/RCTA is malfunctioning. In this case
the BSD/RCTA warning indicator will be
shown on the combination meter display.
When this indicator appears, have your
vehicle inspected by your SUBARU dealer
as soon as possible.
&
BSD/RCTA OFF indica-
tor (if equipped)
The indicator appears when the BSD/
RCTA OFF switch is pressed to deactivate
the BSD/RCTA or when the BSD/RCTA is
suspended temporarily. In this case the
BSD/RCTA OFF indicator will be shown on
the combination meter display. For details,
refer to “BSD/RCTA”
&
RAB warning indica-
tor (if equipped)
This indicator illuminates if the Reverse
Automatic Braking (RAB) system malfunc-
tions. Refer to “Reverse Automatic Brak-
ing (RAB) system”
&
RAB OFF indicator (if
equipped)
This indicator illuminates when the Re-
verse Automatic Braking (RAB) system is
turned off, or when the Reverse Automatic
Braking (RAB) system is suspended tem-
porarily. Refer to “Reverse Automatic
Braking (RAB) system”
&
Icy road surface warn-
ing indicator
When the outside temperature is 37
8
F
(3
8
C) or less, the icy road surface warning
will illuminate to inform the driver that the
road surface may be frozen.
NOTE
.
The outside temperature indicator
shows the temperature in the area
around the sensor. However, the tem-
perature may not be indicated correctly
or the update may be delayed in the
following conditions.
– While parking or driving at low
speeds
– When the outside temperature
changes suddenly (example: when
going in and out of an underground
parking area or when passing
through a tunnel)
– When starting the engine after
Warning and indicator
194
(197,1)
being parked for a certain period of
time
.
The icy road surface warning screen
should be treated only as a guide. Be
sure to check the condition of the road
surface before driving.
.
Once the icy road surface warning
screen appears, it will not disappear
unless the outside temperature has
increased to 41
8
F (5
8
C) or higher.
&
One-touch Interior Illu-
mination indicator (if
equipped)
This indicator light illuminates when the
One-touch Interior Illumination function is
activated. Refer to “One-touch Interior
Illumination function”
3-7. Combination meter dis-
play (color LCD)
WARNING
Always pay adequate attention to
safe driving when operating the
combination meter display while
the vehicle is in motion. When
operation of the combination meter
display interferes with your ability to
concentrate on driving, stop the
vehicle before performing opera-
tions on the screen. Also, do not
concentrate on the display while
driving. Doing so may cause you to
look away from the road and could
result in an accident.
Various information will be shown on the
combination meter display. Also, a warn-
ing message will appear on the display if a
malfunction is detected. In addition, sev-
eral settings for the displayed content can
be performed.
Combination meter display
1)
ECO gauge (Refer to “ECO gauge”
2)
Warning screen (Refer to “Warning
screen”
P197.)/Basic screen (Refer to
3)
EyeSight screen
4)
Telltale screen (Refer to “Telltale screen”
– CONTINUED –
Combination meter display (color LCD)
195
3
Instruments
and
controls
(198,1)
5)
Select lever/gear position indicator (Re-
fer to “Select lever/gear position indica-
tor”
6)
X-MODE indicator (Refer to “X-MODE
indicator”
7)
O d o m e t e r ( R e f e r t o “ O d o m e t e r ”
P171.)/Double trip meter (Refer to
A:
Deactivating the EyeSight system
B:
Activating the EyeSight system
&
Basic operation
Control switch
1)
(Up)
2)
/SET (Enter)
3)
(Down)
By operating “
” or “
” of the control
switch, the screens and selection items
can be switched. When the “
/SET”
switch is pulled toward you, the item can
be selected and set.
If there are some useful messages, such
as vehicle information, warning informa-
tion, etc., they will interrupt the current
screen, and appear on the display accom-
panied by a beep. If such a screen is
displayed, take proper action according to
the message shown on the screen.
The warning screen will return to the
original screen after a few seconds. While
the “
” information reminder is shown on
the display, it may be possible to display
the warning screen again. To recall the
message marked with “
” on the display,
pull the “ /SET” switch on the steering
wheel toward you.
&
Welcome screen (opening
animation) and Good-bye
screen (ending animation)
When the driver’s door is opened and
closed after unlocking the door, the wel-
come screen (opening animation) will
appear on the combination meter display
for approximately 20 seconds.
When the ignition switch is turned to the
“LOCK”/“OFF” position, the combination
meter display gradually turns off by show-
ing Good-bye screen (ending animation).
NOTE
.
The welcome screen and the good-
bye screen may differ in the actual
words and appearance.
.
The basic screen will be shown
when the ignition switch is turned to
the “ON” position while the welcome
screen is displayed.
.
Once the welcome screen appears, it
takes a certain period of time to display
it again.
.
If the ignition switch is operated
after unlocking the driver’s door, the
welcome screen will not appear even
when the driver’s door is opened and
closed.
.
The welcome screen will disappear
when you lock the driver’s door by
using the remote keyless entry system
(all models) or the keyless access
function (if equipped) while the wel-
come screen is displayed.
.
The welcome screen including the
multi-function display (color LCD) and
the audio/navigation unit can be set to
on or off.
.
The welcome screen and the good-
bye screen can be set to on or off. For
details, refer to “Menu screens”
Combination meter display (color LCD)
196
(199,1)
&
Warning screen
Example of warning
If there is a warning message or a
maintenance notification, it will appear on
this screen. Take the appropriate actions
based on the messages indicated.
&
Telltale screen
1)
Telltale screen
When the corresponding situation occurs,
the following telltales will be displayed on
the telltale screen.
NOTE
When there is warning information to
display, it will be displayed in five
warning indicators, starting on the left
in ascending order of severity. If there
are six or more warning information
displayed, pull the “
/SET” switch and
check the item.
Mark
Name
Page
Door open warning light
LED headlight warning
light
High beam assist indi-
cator light
Steering Responsive
Headlight warning light
(if equipped)
Rear differential oil
temperature warning
light (if equipped)
Engine low oil level
warning light
RAB warning indicator
(if equipped)
RAB OFF indicator (if
equipped)
BSD/RCTA warning in-
dicator (if equipped)
BSD/RCTA OFF indi-
cator (if equipped)
Automatic headlight
beam leveler warning
light
– CONTINUED –
Combination meter display (color LCD)
197
3
Instruments
and
controls
(200,1)
Mark
Name
Page
Windshield washer fluid
warning light
Hill descent control in-
dicator
Icy road surface warn-
ing indicator
One-touch Interior Illu-
mination indicator (if
equipped)
&
Basic screens
By operating the “
” or “
” switch on the
steering wheel, you can change the screen
that is always displayed.
Average fuel consumption screen:
: Average fuel consumption
: Driving range on remaining fuel
This screen displays the average rate of
fuel consumption since the trip meter was
last reset.
NOTE
The driving range on the remaining fuel
is only a guide. The indicated value may
differ from the actual driving range on
the remaining fuel, so you must im-
mediately fill the tank when the low fuel
warning light illuminates.
Current fuel consumption screen:
: Current fuel consumption
: Driving range on remaining fuel
This screen displays the rate of fuel
consumption at the present moment.
NOTE
The driving range on the remaining fuel
is only a guide. The indicated value may
differ from the actual driving range on
the remaining fuel, so you must im-
mediately fill the tank when the low fuel
warning light illuminates.
Combination meter display (color LCD)
198
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст