Subaru BRZ (2022 year). Manual in english — page 5
90
SRS Airbag (Supplemental Restraint System Airbag)
-
Installation of additional elec-
Attachment of any equipment
■ How to Contact the Vehicle
trical/electronic
equipment
(bush bar, winches, snow plow,
Manufacturer concerning
such as a mobile two-way
skid plate, etc.) other than
Modifications for Persons
radio on or near the SRS
genuine SUBARU accessory
with Disabilities That May
airbag system components
parts to the front end.
and/or wiring is not advisable.
Affect the Advanced Airbag
Modification of the suspension
This could interfere with
system or front end structure.
System
proper operation of the SRS
Installation of a tire of different
Changing or moving any parts of the front
airbag system.
size and construction from the
seats, rear seat, seatbelts, front bumper,
-
Modifications on or inside the
tires specified on the vehicle
front side frame, radiator panel, instru-
door panels for the purpose of
placard attached to the driver’s
ment panel, combination meter, steering
a speaker replacement or
center pillar or specified for indi-
wheel, steering column, tire, suspension
sound insulation
vidual vehicle models in this
or floor panel can affect the operation of
The impact sensors, which detect
Owner’s Manual.
the SUBARU advanced airbag system. If
the pressure of an impact, are
Attachment of any equipment
you have any questions, you may contact
located in the doors. Do not
(side steps or side sill protectors,
the following SUBARU distributors.
modify any components of the
etc.) other than genuine SUBARU
<Continental U.S., Alaska and the District
doors or door trims, such as the
accessory parts to the side body.
of Columbia>
addition of door speakers for
Subaru of America, Inc.
example. Any modifications to
Customer Advocacy Department
the doors will create a risk of the
Always consult your SUBARU dealer if
airbag system becoming inopera-
you want to install any accessory parts on
One Subaru Drive
tive or unintended airbag deploy-
your vehicle.
P.O. Box 9103
ment.
Camden, NJ 08101-9877
1-800-SUBARU3 (1-800-782-2783)
<Hawaii>
CAUTION
Subaru Hawaii
Do not perform any of the following
2850-A Pukoloa St.,
modifications. Such modifications
Honolulu, HI 96819
can interfere with proper operation
877-215-0338
of the SRS airbag system.
<Guam>
SRS Airbag (Supplemental Restraint System Airbag)
91
Shen’s Corporation dba Prestige Automo-
biles
491 East Marine Corps Drive,
Dededo, Guam 96929
671-633-2698
1
<Puerto Rico>
Trebol Motors
296 Marginal JF Kennedy, San Juan,
Puerto Rico
787-793-2828
<Canada>
Subaru Canada, Inc.
Consumer Support Department
560 Suffolk Court, Mississauga, Ontario
L5R 4J7
1-800-894-4212
There are currently no SUBARU distribu-
tors in any other U.S. territories. If you are
in such an area, please contact the
SUBARU distributor or dealer from which
you bought your vehicle.
Keys and Doors
2-1. Keyless Access with Push-Button Start
Setting Audible Signal Operation (If Equipped)
110
System
94
Selecting Hazard Warning Flasher Operation
110
Vehicle Finder Function
110
Safety Precautions
94
Locking and Unlocking with “Keyless Access”
Sounding a Panic Alarm
110
Entry Function
97
Replacing the Battery
111
Unlock Using PIN Code Access
100
Replacing Lost Transmitters
111
Power Saving Function
102
2-4. Door Locks
111
Power Saving Function of Access Key Fob
103
Locking and Unlocking from the Outside
111
2
Disabling Keyless Access Function
103
Locking and Unlocking from the Inside
112
Selecting Audible Signal Operation (If Equipped)
105
Key Lock-In Prevention Function
113
Selecting Hazard Warning Flasher Operation
106
Battery Drainage Prevention Function
113
Warning Chimes and Warning Indicator
106
2-5. Alarm System
114
When Access Key Fob Does Not Operate
Alarm System Operation
114
Properly
106
Arming the System
114
Replacing Battery of Access Key Fob
106
Disarming the System
115
Replacing Access Key Fob
106
Alarm System Setting
115
Certification for Keyless Access with Push-Button
If You Have Accidentally Triggered the Alarm
Start System
106
System
116
2-2. Immobilizer
108
2-6. Windows
116
Security Indicator Light
108
Power Window Operation
117
Key Replacement
108
Initialization of Power Window
118
Certification for Immobilizer System
108
2-7. Trunk Lid
119
2-3. Remote Keyless Entry System
109
To Open and Close the Trunk Lid from Outside
120
Locking the Doors
110
To Open the Trunk Lid from Inside
121
Unlocking the Doors
110
Internal Trunk Lid Release Handle
121
Opening the Trunk Lid
110
94
Keyless Access with Push-Button Start System
2-1. Keyless Access with
Arming and disarming the alarm
system. For detailed information, refer to
Push-Button Start System
"Alarm System" ) P114.
1
The following access
key
fobs
are
provided with the vehicle.
NOTE
Locking and unlocking by the
remote keyless entry system can also
be controlled with the buttons on the
access key fob. For detailed informa-
tion, refer to "Remote Keyless Entry
2
System" ) P109.
Carefully store the key number plate
202500
supplied with the access key fob. It is
necessary for vehicle repair and addi-
1)
Release button
tional registration of access key fobs.
2)
Emergency key
1
1
2
For details, refer to "Key Replacement"
While pressing the release button of the
) P108.
access key fob, take out the emergency
203629
An emergency key is attached to each
key.
access key fob.
1) Access key fob
The emergency key is used for locking
2) Key number plate
and unlocking the driver’s door.
The keyless access with push-button start
system allows you to perform the following
■ Safety Precautions
functions when you are carrying the
access key fob.
WARNING
Locking and unlocking of the doors,
If you wear an implanted pacemaker
fuel filler lid
or an implanted defibrillator, stay at
Opening the trunk
least 8.7 in (22 cm) away from the
Starting and stopping the engine. For
transmitting antennas installed on
detailed information, refer to "Starting and
the vehicle.
Stopping Engine" ) P229.
Keyless Access with Push-Button Start System
95
The radio waves from the transmit-
The keyless access with push-
ting antennas on the vehicle could
button start system uses radio
1
adversely affect the operation of
waves of the following frequency*
implanted
pacemakers
and
in addition to the radio waves
implanted defibrillators.
used for the remote keyless entry
system. The radio waves are peri-
If you wear electronic medical
odically output from the antennas
equipment other than an implanted
2
installed on the vehicle as shown
pacemaker or an implanted
in the following illustrations.
defibrillator, before using the key-
*: Radio frequency: 134 kHz
less access with push-button start
system, refer to “Radio waves used
for the keyless access with push-
1
button start system” mentioned
later, and contact the electronic
1
1
medical equipment manufacturer
for more information. The radio
waves from the transmitting anten-
nas on the vehicle could adversely
affect the operation of the elec-
tronic medical equipment.
“Radio waves used for the keyless
access with push-button start sys-
tem”
204126
1)
Antenna
- CONTINUED -
96
Keyless Access with Push-Button Start System
-
Never leave the access key
When traveling in an airplane, do
CAUTION
fob in direct sunlight or
not press the button of the access
Never leave or store the access
anywhere that may become
key fob. If any button of the
key fob inside the vehicle or
hot, such as on the dash-
access key fob is pressed, radio
within
6.6 ft
(2 m) around the
board. It may damage the
waves are emitted and may affect
vehicle (e.g., in the garage). The
battery or cause circuit
the operation of the airplane. In a
access key fob may be locked
malfunctions.
bag, take measures to prevent the
inside the vehicle, or the battery
buttons from being pressed acci-
-
Do not wash the access key
may discharge rapidly. Note that
dentally.
fob in an ultrasonic washer.
the push-button ignition switch
-
Do not leave the access key
may not turn on in some cases
fob in humid or dusty loca-
depending on the location of the
NOTE
tions. Doing so may cause
access key fob.
The
operational/non-operational
malfunctions.
The access key fob contains elec-
setting for the keyless access function
-
Keep the access key fob away
tronic components. Observe the
can be changed. For the setting proce-
from magnetic sources.
following precautions to prevent
dure, refer to "Disabling Keyless
malfunctions.
-
Do not leave the access key
Access Function" ) P103.
fob near a personal computer
For detailed information about the
-
It is recommended to have the
or home electrical appliance.
operation method for the push-button
access key fob battery
-
Do not leave the access key
ignition switch while the keyless
replaced at an authorized
fob near a battery charger or
access function is switched to the non-
SUBARU dealer to avoid the
risk of damage.
any electrical accessories.
operational mode, refer to "Access Key
Fob - If Access Key Fob Does Not
-
Do not get the access key fob
-
Do not apply metallic window
Operate Properly" ) P325.
wet. If the access key fob gets
tint or attach metallic objects
The keyless access with push-
wet, wipe it off immediately
to the windows.
button start system uses weak radio
and let it dry completely.
-
Do not fit non genuine acces-
waves. The status of the access key
-
Do not apply strong impacts
sories or parts.
fob and environmental conditions may
to the access key fob.
If the access key fob is dropped,
interfere with the communication
the integrated emergency key
between the access key fob and the
inside may become loose. Be
vehicle under the following conditions,
careful not to lose the emergency
and it may not be possible to lock or
key.
unlock the doors or start the engine.
Keyless Access with Push-Button Start System
97
-
When operating near a facility
If an access key fob is lost, it is
-
On the instrument panel
where strong radio waves are trans-
recommended that all of the remaining
-
On the floor
mitted, such as a broadcast station
access key fobs be reregistered. For
-
Inside the glove box
and power transmission lines.
reregistration of an access key fob,
-
Inside the door trim pocket
-
When products that transmit
contact a SUBARU dealer.
-
On the rear seat
radio waves are used, such as an
For a spare access key fob, contact
-
On the rear shelf
access key fob or a remote trans-
a SUBARU dealer.
-
Inside the trunk
mitter key of another vehicle.
Up to 7 access key fobs can be
If you do, the following situations
2
-
When carrying the access key
registered for one vehicle.
may occur.
fob of your vehicle together with the
Do not leave the access key fob in
-
The access key fob is mistakenly
access key fob or the remote trans-
the storage spaces inside the vehicle,
locked inside the vehicle.
mitter of another vehicle.
such as the door pocket, dashboard or
-
A false warning issues although
-
When the access key fob is
inside the corner of the trunk. Vibra-
no malfunction actually occurs.
placed near wireless communica-
tions may damage the access key fob
-
No warning issues even when a
tion equipment such as a cell phone.
or turn on the switch, possibly
malfunction occurs.
-
When the access key fob is
resulting in a lockout.
placed near a metallic object.
After the vehicle battery is
■ Locking and Unlocking with
-
When metallic accessories are
discharged or replaced, initialization of
“Keyless Access” Entry
attached to the access key fob.
the steering lock system may be
Function
-
When carrying the access key
required to start the engine. In this
fob with an electronic appliance
case, perform the following procedure
When the access key fob is carried within
such as a laptop computer.
to initialize the steering lock.
the operating range, the doors, the fuel
-
When the battery of the access
(1) Turn the push-button ignition
filler lid can be locked/unlocked just by
key fob is discharged.
switch to the “OFF” position. For
touching the door handle.
The access key fob is always
details, refer to "Switching Power
communicating with the vehicle and is
Status" ) P125.
NOTE
continuously using the battery.
(2) Open and close the driver’s door.
The vehicle can also be locked/
Although the life of the battery varies
(3) Wait for approximately
10
unlocked with the remote keyless
depending on the operating condi-
seconds.
entry system. For details, refer to
tions, it is approximately 1 to 2 years. If
When the steering is locked, the initial-
"Remote Keyless Entry System"
the battery becomes fully discharged,
ization is completed.
) P109.
replace it with a new one.
Do not leave the access key fob in
the following places.
- CONTINUED -
98
Keyless Access with Push-Button Start System
▼ Operating ranges
When the access key fob is within either of
keyless access function when the
the operating ranges of the doors, the
access key fob is inside the vehicle.
LED indicator on the access key fob
However, depending on the status of
2
1
flashes. When the keyless access func-
the access key fob and the environ-
1
tions are disabled, the LED indicator does
mental conditions, the access key fob
not flash unless a button on the access
may be locked inside the vehicle.
key fob is pressed.
Before locking the vehicle, make sure
that you have the access key fob.
NOTE
When the battery of the access key
If the access key fob is placed too
fob is discharged, or when operating it
close to the vehicle body, the keyless
in a location with strong radio waves or
2
noise (e.g., near a radio tower, power
access functions may not operate
1
properly. If it does not operate prop-
plant, broadcast station or an area
2
where wireless equipment is used), or
204127
erly, repeat the operation from farther
away.
while talking on a cell phone, the oper-
1)
Antenna
If the access key fob is placed near
ating ranges may be reduced, or the
2)
Operating range (approximately 16 to
the ground or in an elevated location
keyless access function may not
32 in (40 to 80 cm))
from the ground, even if it is in the indi-
operate.
cated operating range, the keyless
In such a case, perform the procedure
access function may not operate prop-
described in "Locking and Unlocking"
erly.
) P326.
1
The doors may lock or unlock when
When the access key fob is within
the operating range, it is possible for
the car is being washed or exposed to
anyone, even someone who is not
a significant amount of water that
carrying the access key fob, to operate
touches the door handle while the key
the keyless access function. Note that
fob is still in the operating range.
the keyless access function can be
operated only by the door handle, door
▼ How to lock and unlock
lock sensor or trunk opener button in
It is possible to perform the following oper-
the operating range in which the
ations when you are carrying the access
202501
access key fob is detected.
key fob.
1)
LED indicator
It is not possible to lock the doors,
Lock and unlock the doors and the fuel
trunk lid and fuel filler lid using the
filler lid
Keyless Access with Push-Button Start System
99
Unlock the trunk lid
When locking, be sure to carry the
filler lid will be locked. Also, an electronic
access key fob to prevent locking the
chirp will sound once and the hazard
NOTE
access key fob in the vehicle.
warning flashers will flash once.
It is not possible to lock the doors
The setting of the hazard warning
and fuel filler lid using the keyless
flasher operation and the volume of the
NOTE
access function when the push-button
audible signal can be changed by your
After touching the door lock sensor to
ignition switch is in the “ACC” or “ON”
SUBARU dealer. Contact your
lock all of the doors, if you touch the
position. Refer to "Switching Power
SUBARU dealer for details. The setting
door lock sensor twice more to
2
Status" ) P125.
of the hazard warning flasher operation
attempt the lock operation without first
If the door handle is gripped with a
can be changed by operating the
unlocking the doors, nothing will hap-
gloved hand, the door lock may not be
center information display. For details,
pen, even if the door lock sensor is
released.
refer to "Car settings" ) P165.
touched. In this case, perform the
If the door lock sensor is touched
unlocking operation once first. You
four times or more repeatedly, the
▽ Locking with the door lock
can then touch the door lock sensor to
system will ignore the sensor opera-
sensor
lock the doors.
tion.
When performing the locking proce-
▽ Unlocking
dure too quickly, locking may not
complete.
If any of the doors are not fully
closed, an electronic chirp sounds 5
seconds to alert you that the doors are
not properly closed.
It is possible to lock a closed door
even if the other door is open. After
performing the locking procedure,
1
close the opened door to lock it.
Within 3 seconds after locking the
204128
doors using the keyless access func-
1)
Door lock sensor
tion, it is not possible to unlock doors
204129
using the keyless access function.
Carry the access key fob, close all doors
Carry the access key fob, and touch the
and touch the door lock sensor on the
sensor behind the door handle.
door handle. All doors including the fuel
- CONTINUED -
100
Keyless Access with Push-Button Start System
When the driver’s door handle is
The trunk lock/unlock setting is on.
■ Unlock Using PIN Code
gripped, only the driver’s door and the fuel
All doors are unlocked.
Access
filler lid will be unlocked.
The trunk lock/unlock setting can be
When the passenger’s door handle is
changed by a SUBARU dealer. Contact
gripped, all doors (including the trunk lid)
your SUBARU dealer to change the
and the fuel filler lid will be unlocked.
setting.
Also, an electronic chirp will sound twice
▼ Door unlock selection function
and the hazard warning flashers will flash
twice.
When the door is unlocked using the
keyless access function, only the doors
▽ Opening trunk
that were set and the fuel filler lid can be
1
unlocked.
The settings can be changed with the
following methods.
204130
The setting can be changed by oper-
ating the center information display.
1) Trunk opener button
For details, refer to "Car settings" ) P165.
While all doors are locked, you can unlock
The setting can be changed by a
the doors without a key by operating the
SUBARU dealer.
trunk opener button.
1
NOTE
PIN Code Access will be helpful if the
204166
key is accidentally left in the vehicle. It
1) Trunk opener button
is recommended that a 5-digit security
code (PIN code) is registered.
Carry the access key fob, and press the
trunk opener button. The trunk will open.
NOTE
Under the following conditions, the
trunk can be opened without the key
fob.
Keyless Access with Push-Button Start System
101
▼ Registration for a PIN code
Steps
Operation
Time from the previous step
1
Turn off the ignition switch.
ʊ
2
Close all doors (including trunk).
ʊ
Press and hold the “
” button on the access key fob, then press and hold the
3
ʊ
trunk opener button until a chirp sounds intermittently.
2
4
Press the “
” button on the access key fob.
Within 30 seconds
Input the PIN code using the trunk opener button within 30 seconds after the
chirp sound of step 4.
For example, to register “32468” as the PIN code, perform the following pro-
cedure.
(1)
Press the button three times.
Within 30 seconds
(2)
After a chirp sounds once, press the button twice.
5
(3)
After a chirp sounds once, press the button four times.
(4)
After a chirp sounds once, press the button six times.
(5)
After a chirp sounds once, press the button eight times.
Perform step 5 again within approximately 30 seconds after the chirp starts
6
ʊ
sounding intermittently.
7
All doors will be unlocked and locked. Then the PIN code will be registered.
ʊ
- CONTINUED -
102
Keyless Access with Push-Button Start System
NOTE
The PIN code cannot be deleted
■ Power Saving Function
while the keyless access function is
Press the trunk opener button ten
To protect the access key fob battery and
disabled by operating the access key
times to enter “0”.
the vehicle battery, the keyless access
Change the PIN code frequently to
fob.
function will be disabled as follows.
protect your vehicle from theft.
Reregister the PIN code in the
following case.
When the keyless access function and
If you have lent your vehicle to
-
When you forget the PIN code
the remote keyless entry system have not
another person, confirm that the PIN
-
When you want to change the
been used:
code has not been changed or deleted.
If the PIN code has been changed or
PIN code
(1)
5 days after the push-button igni-
tion switch has been turned off,
deleted, reregister a new PIN code.
▼ Unlocking
communication between the antennas
If you make an error during the
and the access key fob will be stopped.
registration procedure, press the “
”
Perform steps
(1) to
(5) of step
5
(2)
9 days after step (1), the sensors
or “
” button on the access key fob.
described in “Registration”.
Then, start over from the procedure
(both lock sensor and unlock sensor)
described in “Registration for a PIN
on the passenger’s door will be
NOTE
code”.
disabled.
You cannot unlock by PIN Code
To protect your vehicle from theft,
When the access key fob has been left
Access in the following cases.
you cannot register “00000” to “99999”
in the operating range for 10 minutes or
-
When the access key fob is
or “12345” as a PIN code.
longer while all doors are locked, the
within the operating ranges
keyless access function will be disabled.
Do not register your vehicle license
-
When the ignition switch is in the
plate number or simple numbers such
“ACC” or “ON” position
▼ Recovery from power saving mode
as “11122” or “12121” as a PIN code.
If you make an operation error
Doing so will increase the risk of
during the unlocking procedure, start
When one of the following operations is
vehicle theft.
performed, the keyless access function
over with the unlocking procedure
When you try to register “22222”,
will be recovered.
after waiting for 5 seconds or longer.
the registered PIN code will be deleted.
To protect your vehicle from theft, a
Unlock by gripping the door handle
You cannot unlock the doors by PIN
buzzer will sound if incorrect PIN
(only when the sensors on the
Code Access until a new code is regis-
codes are entered five times continu-
passenger’s door are not disabled) or
tered.
ously. If this occurs, you cannot unlock
pressing the trunk opener button on the
After registering a new PIN code,
the doors by PIN Code Access for 5
trunk lid
make sure that you can unlock the
minutes.
Lock or unlock by the remote keyless
doors using the PIN code.
entry system
Keyless Access with Push-Button Start System
103
Open a door and then close it
and push-button start system will not be
dure described in "Starting Engine"
Turn the push-button ignition switch to
available.
) P326.
the “ON” position
To cancel the power save mode, press
one of the buttons on the access key fob.
▼ Disabling functions
■ Power Saving Function of
■ Disabling Keyless Access
▽ By operating the access key fob
Access Key Fob
Function
To disable the keyless access function by
This function stops the access key fob
2
operating the access key fob, register a
from receiving signals and helps minimize
WARNING
PIN code for PIN Code Access. For
the battery consumption of the access key
details about registering a PIN code, refer
fob.
If you have an implanted pacemaker
to "Unlock Using PIN Code Access"
or an implanted defibrillator, per-
) P100.
1. Press the
“
” button twice while
form the procedure "By operating
holding the “
” button.
the driver’s door" ) P104 to disable
1. Open the driver’s door.
the keyless access function. If you
perform the procedure "By operat-
1
ing the access key fob" ) P103, the
operation of an implanted pace-
maker or implanted defibrillator
may be affected by the radio waves
from the transmitter antenna.
When the vehicle is not going to be used
for a long time, or when you choose not to
use the keyless access function, the
202501
keyless access function can be disabled.
203610
1) LED indicator
NOTE
2. Rotate the lock lever forward.
2. Confirm that the LED indicator blinks 4
The locking and unlocking function
times to notify that the setting is complete.
by the remote keyless entry system is
When the access key fob is in the power
not disabled.
save mode, the keyless access function
To start the engine while the func-
tions are disabled, perform the proce-
- CONTINUED -
104
Keyless Access with Push-Button Start System
To disable the keyless access function by
operating the driver’s door, perform the
following procedures.
202646
3. Press and hold the “
” button and
“
” button on the access key fob simul-
taneously for more than 5 seconds.
A chirp sound will be heard, and the func-
tion will be disabled.
▽ By operating the driver’s door
204132
Keyless Access with Push-Button Start System
105
▼ Enabling functions
Steps
Operation
Time
Status
When the procedure to disable the func-
1
Sit in the driver’s seat, and close the door.
ʊ
Close
tions is performed again, a chirp sound
Push “
” on the power door locking
2
ʊ
Close
will be heard, and the functions are
switch.
enabled.
3
Open the driver’s door.
Within 5 sec.
CloseĺOpen
Push “
” on the power door locking switch
NOTE
4
Within 5 sec.
Open
2
twice.
The keyless access function will be
OpenĺCloseĺOpenĺ
enabled only if you perform the proce-
5
Close and open the driver’s door twice.
Within 10 sec.
CloseĺOpen
dure in the same manner you disabled
the function
(for example, when
Push “
” on the power door locking switch
6
Within 10 sec.
Open
disabling by operating the driver’s
twice while the door is open.
door, the function will not be enabled
7
Close and open the driver’s door once.
Within 10 sec.
OpenĺCloseĺOpen
even if you operate the access key
8
Close the door.
Within 5 sec.
OpenĺClose
fob).
Press the push-button ignition
A chirp will sound and the functions will be disabled.
switch if you do not know the proce-
dure in which the keyless access func-
NOTE
tion was disabled.
In steps 4 and 6, press the power door locking switch firmly. If the switch is not
-
When disabling by operating the
pressed firmly, the functions may not be disabled.
driver’s door: a chirp will not be
heard
-
When disabling by operating the
access key fob: a chirp will be heard
■ Selecting Audible Signal
Operation (If Equipped)
Using an electronic chirp, the system will
give you an audible signal when the doors
are locked or unlocked. If desired, you can
turn the audible signal off by operating the
- CONTINUED -
106
Keyless Access with Push-Button Start System
center information display. For details,
■ When Access Key Fob Does
CAUTION
refer to "Car settings" ) P165.
Not Operate Properly
Furthermore, the volume setting of the
FCC WARNING
Refer to "Access Key Fob - If Access Key
audible signal can also be changed by a
Fob Does Not Operate Properly" ) P325.
Changes or modifications not
SUBARU dealer. Consult your SUBARU
expressly approved by the party
dealer for details.
■ Replacing Battery of Access
responsible for compliance could
Key Fob
void the user’s authority to operate
■ Selecting Hazard Warning
the equipment.
Flasher Operation
Refer to "Replacing Battery of Access Key
Fob" ) P376.
Using the hazard warning flasher, the
This device complies with part 15 of the
system will give you a visible signal when
■ Replacing Access Key Fob
FCC Rules. Operation is subject to the
the doors are locked or unlocked. If
following two conditions: (1) This device
desired, you can turn the hazard warning
Access key fobs can be replaced at
may not cause harmful interference, and
flashers off by operating the center infor-
SUBARU dealers. For more details,
(2) this device must accept any interfer-
mation display. For details, refer to "Car
contact a SUBARU dealer.
ence received, including interference that
settings" ) P165. The setting can also be
may cause undesired operation.
changed by a SUBARU dealer. Consult
■ Certification for Keyless
your SUBARU dealer for details.
Access with Push-Button
Start System
■ Warning Chimes and
U.S.-spec. models
Warning Indicator
FCC ID: HYQ14AHK
The keyless access with push-button start
FCC ID: Y8PSU19S-3
system is equipped with a warning chime
and the access key warning indicator in
FCC ID: Y8PSSPIMB03
order to minimize improper operations
and help protect your vehicle from theft.
For details, refer to "Warning Chimes and
Warning Indicator of the Keyless Access
with Push-Button Start System" ) P143.
Keyless Access with Push-Button Start System
107
Canada-spec. models
Mexico-spec. models
2
204233
IFT
RLVDE1415-1661
14AHK
DENSO
204234
204232
108
Immobilizer
2-2. Immobilizer
-
Before leaving your vehicle,
For details about new key registration
close all windows and lock the
and erasing the lost key’s ID code,
The immobilizer system is designed to
doors.
contact your SUBARU dealer.
prevent an unauthorized person from
-
Do not leave spare keys or any
starting the engine. Only keys registered
record of your key number in the
■ Certification for Immobilizer
with your vehicle’s immobilizer system
vehicle.
System
can be used to operate your vehicle. If
The vehicle has a maintenance-free
Refer to "Certification for Keyless Access
engine start is attempted with an unregis-
type immobilizer system.
with Push-Button Start System" )
P106.
tered access key fob or key, the engine
will not start. Even if the engine does start,
■ Security Indicator Light
it will stop after a few seconds. This
Refer to "Security Indicator Light" ) P148.
system, however, is not a 100% anti-theft
guarantee.
■ Key Replacement
CAUTION
Your key number plate will be required if
you ever need a replacement key made.
Do not place the key under direct
Any new key must be registered for use
sunlight or anywhere it may
with your vehicle’s immobilizer system
become hot.
before it can be used. The maximum
Do not get the key wet. If the key
number of keys that can be registered for
gets wet, wipe it dry with a cloth
use with one vehicle is seven.
immediately.
One key that has already been registered
Do not modify or remove the
is required in order to register a new key.
system. If modified or removed,
the proper operation of the
NOTE
system cannot be guaranteed.
If you lose a key, the lost key’s ID code
still remains in the memory of the vehi-
NOTE
cle’s immobilizer system. For security
To protect your vehicle from theft,
reasons, the lost key’s ID code should
please pay close attention to the
be erased from the memory. To erase
the lost key’s ID code, all keys that will
following security precautions:
be used are required.
-
Never leave your vehicle unat-
tended with its keys inside.
Remote Keyless Entry System
109
2-3. Remote Keyless Entry
distance will be shorter in areas near a
facility or electronic equipment emitting
System
strong radio waves such as a power plant,
1
broadcast station, TV tower, or remote
CAUTION
controller of home electronic appliances.
2
Do not expose the remote trans-
3
NOTE
mitter to severe shocks, such as
The remote keyless entry system
2
those experienced as a result of
4
will not be activated when the push-
dropping or throwing.
button ignition switch is in any posi-
Do not take the remote trans-
tion other than the “OFF” position.
mitter
apart except when
The hazard warning flashers will
replacing the battery.
202502
flash once or twice when the access
Do not get the remote transmitter
Access key fob
key fob button is pressed in the
wet. If it gets wet, wipe it dry with
1) Lock/arm button
following cases.
a cloth immediately.
2) Unlock/disarm button
-
When locking the doors
When you carry the remote trans-
3) Trunk lid opener button
-
When unlocking the doors
mitter on an airplane, do not
4) PANIC button
If desired, you can turn the hazard
press the button of the remote
warning flashers off by operating the
transmitter while in the airplane.
The remote keyless entry system has the
center information display. For details,
When any button of the remote
following functions.
refer to "Car settings" ) P165. The set-
transmitter is pressed, radio
Locking and unlocking the doors and
ting can also be changed by a
waves are sent and may affect the
fuel filler lid
SUBARU dealer. Consult your
operation of the airplane. When
Opening the trunk lid
SUBARU dealer for details.
you carry the remote transmitter
Sounding a panic alarm
The setting of the Remote Keyless
in a bag on an airplane, take
Entry System operation can be
Arming and disarming the alarm
measures to prevent the buttons
changed by your SUBARU dealer.
system. For details, refer to "Alarm
of the remote transmitter from
Consult your SUBARU dealer for
System" ) P114.
being pressed.
details. For details, refer to "Function
The operable distance of the remote
Settings and Adjustments Performed
keyless entry system is approximately 30
by a Dealer" ) P391.
feet (10 meters). However, this distance
will vary depending on environmental
conditions. The system’s operable
- CONTINUED -
110
Remote Keyless Entry System
■ Locking the Doors
■ Opening the Trunk Lid
changed by a SUBARU dealer. Consult
your SUBARU dealer for details.
Press the “
” button to lock all doors and
Press and hold the “
” button to open
fuel filler lid. An electronic chirp will sound
the trunk lid. An electronic chirp will sound
■ Vehicle Finder Function
once and the hazard warning flashers will
once.
flash once.
Use this function to find your vehicle
This operation setting can be changed by
parked among many vehicles in a large
If any of the doors are not fully closed, an
a SUBARU dealer. Consult your SUBARU
parking lot. Provided you are within 30
electronic chirp sounds 5 seconds to alert
dealer for details.
feet (10 meters) of the vehicle, pressing
you that the doors are not properly closed.
the “
” button three times in a 5-second
When you close the door, it will automati-
■ Setting Audible Signal Oper-
period will cause your vehicle’s horn to
cally lock and then the following will occur.
ation (If Equipped)
sound once and its hazard warning
An electronic chirp sounds once.
Using an electronic chirp, the system will
flashers to flash three times.
The hazard warning flashers flash
give you an audible signal when the doors
once.
lock and unlock.
NOTE
If desired, you can turn the audible signal
If the interval between presses is too
■ Unlocking the Doors
off by operating the center information
short when you press the “
” button
Press the “
” button to unlock the driver’s
display. For details, refer to "Car settings"
three times, the system may not
door and the fuel filler lid. An electronic
) P165. Furthermore, the volume setting
respond to the signals from the remote
chirp will sound twice and the hazard
of the audible signal can also be changed
transmitter.
warning flashers will flash twice. To unlock
by a SUBARU dealer. Consult your
all doors, briefly press the “
” button again
SUBARU dealer for details.
■ Sounding a Panic Alarm
within 5 seconds.
To activate the alarm, press the “PANIC”
■ Selecting Hazard Warning
button once.
NOTE
Flasher Operation
The horn will sound and the hazard
If the interval between the first and
warning flashers, headlights, side marker
second presses of the “
” button (for
lights, tail lights and map lights will flash.
Using the hazard warning flasher, the
unlocking of all of the doors) is
system will give you a visible signal when
To deactivate the panic alarm, press any
extremely short, the system may not
the doors are locked or unlocked. If
button on the remote transmitter. If a
respond.
desired, you can turn the hazard warning
button on the remote transmitter is not
flashers off by operating the center infor-
pressed, the alarm will be deactivated
mation display. For details, refer to "Car
after approximately 60 seconds.
settings" ) P165. The setting can also be
111
Door Locks
■ Replacing the Battery
2-4. Door Locks
▼ How to lock and unlock the vehicle
using the emergency key
Refer to "Replacing Battery" ) P375.
■ Locking and Unlocking from
■ Replacing Lost Transmitters
the Outside
If you lose a transmitter or want to
NOTE
purchase additional transmitters
(up to
four can be programmed), you should re-
If you unlock the driver’s door with an
2
program all of your transmitters for secu-
emergency key and open the door
rity reasons. For details, contact your
while the alarm system is armed, the
SUBARU dealer and have the transmit-
alarm system is triggered and the vehi-
1
ters programmed into the remote keyless
cle’s horn sounds. In this case, per-
entry system.
form any of the following operations:
2
Press unlock button on the access
key fob.
204167
Turn the push-button ignition switch
1)
Rotate the key toward the front to lock.
to the “ACC” position.
2)
Rotate the key toward the rear to
Carry the access key fob and
unlock.
perform either of the following proce-
dures.
In this case, only the driver’s side door is
-
Grip the door handle.
locked or unlocked.
-
Press the trunk opener button.
For details about the alarm system,
NOTE
refer to "Alarm System" ) P114.
The emergency key is directional. If
the key cannot be inserted, change the
direction that the grooved side is fac-
ing and insert it again.
▼ How to lock the vehicle without
using the key
To lock the door from outside without the
key, the following methods are available.
- CONTINUED -
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст