Subaru Legacy (2005 year). Manual — part 934
LI-33
LIGHTING SYSTEM
High-mounted Stop Light
28.High-mounted Stop Light
A: REMOVAL
1. SEDAN MODEL
1) Disconnect the ground cable from battery.
2) Push the high-mounted stop light backward of
the vehicle (1), raise the rear portion of it (2) and re-
move the clips to remove it.
3) Remove the harness from clamp.
4) Disengage two claws (A), pull out the high-
mounted stop light from the cover and remove the
claw (B).
5) Remove three claws and remove the lens (A).
6) Remove the bulb.
2. WAGON MODEL
1) Disconnect the ground cable from battery.
2) Detach the roof spoiler. <Ref. to EI-40, REMOV-
AL, Roof Spoiler.>
3) Remove the nuts (A), then detach the high-
mounted stop light.
B: INSTALLATION
Install in the reverse order of removal.
C: INSPECTION
1. SEDAN (STANDARD TYPE)
1) Visually check the bulb for blow out.
2) Check the bulb specification. <Ref. to LI-2,
SPECIFICATION, General Description.>
3) If NG, replace the bulb with a new one.
2. SEDAN (REAR SPOILER BUILT-IN
TYPE) AND WAGON
1) Install the high-mounted stop light to test if it illu-
minates normally.
2) If the high-mounted stop light does not illumi-
nate, replace it with a new one.
NOTE:
Since LED (Light Emitting Diode) is used for the
high-mounted stop light of wagon model, replace
the high-mounted stop light assembly when the
LED is powered off.
(1) Harness
(2) Clamp
(1)
(2)
LI-00333
(2)
(1)
LI-00334
LI-00309
(A)
(B)
LI-00310
(A)
LI-00312
(A)
(A)
LI-34
LIGHTING SYSTEM
Spot Map Light
29.Spot Map Light
A: REMOVAL
1) Disconnect the ground cable from battery.
2) Remove the lens (A) and spot map light mount-
ing screws (B).
• Model with sunroof
• Model without sunroof
3) Disconnect the harness connectors and remove
the spot map light.
B: INSTALLATION
Install in the reverse order of removal.
C: INSPECTION
1. SPOT MAP LIGHT BULB
1) Visually check the bulb for blow out.
2) Check the bulb specification. <Ref. to LI-2,
SPECIFICATION, General Description.>
3) If NG, replace the bulb with a new one.
2. SPOT MAP LIGHT SWITCH
Measure the resistance between spot map light
switch terminals.
LI-00313
(A)
LI-00314
(B)
LI-00320
(B)
(B)
Switch position
Terminal No.
Standard
OFF
—
More than 1 M
Ω
ON
1 and 2
18
±5.4 Ω
LI-35
LIGHTING SYSTEM
Room Light
30.Room Light
A: REMOVAL
1) Disconnect the ground cable from battery.
2) Remove the lens (A) and mounting screws (B).
3) Disconnect the harness connector and remove
the room light.
B: INSTALLATION
Install in the reverse order of removal.
C: INSPECTION
1. ROOM LIGHT BULB
1) Visually check the bulb for blow out.
2) Check the bulb specification. <Ref. to LI-2,
SPECIFICATION, General Description.>
3) If NG, replace the bulb with a new one.
2. ROOM LIGHT SWITCH
Measure the resistance between room light switch
terminals.
LI-00315
(A)
LI-00316
(B)
Switch position
Terminal No.
Standard
OFF
—
More than 1 M
Ω
ON
1 and 3
1.5
±0.5 Ω
DOOR
2 and 3
1.5
±0.5 Ω
LI-00257
3 2 1
LI-36
LIGHTING SYSTEM
Luggage Room Light
31.Luggage Room Light
A: REMOVAL
1) Disconnect the ground cable from battery.
2) Remove luggage room light body (A).
3) Disconnect the harness connector and remove
the lens.
B: INSTALLATION
Install in the reverse order of removal.
C: INSPECTION
1. LUGGAGE ROOM LIGHT BULB
1) Visually check the bulb for blow out.
2) Check the bulb specification. <Ref. to LI-2,
SPECIFICATION, General Description.>
3) If NG, replace the bulb with a new one.
2. LUGGAGE ROOM LIGHT SWITCH
Measure the resistance between luggage room
light switch terminals.
Switch position
Terminal No.
Standard
OFF
—
More than 1 M
Ω
ON
1 and 2
1.5
±0.5 Ω
DOOR
2 and 3
1.5
±0.5 Ω
LI-00258
(A)
LI-00259
3
2
1
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст