Subaru Legacy IV (2008 year). Manual — part 117

EN(H4SO)(diag)-71

Diagnostics for Engine Starting Failure

ENGINE (DIAGNOSTICS)

D: IGNITION CONTROL SYSTEM

CAUTION:
After repair or replacement of faulty parts, perform Clear Memory Mode <Ref. to EN(H4SO)(diag)-50,
Clear Memory Mode.>, and Inspection Mode <Ref. to EN(H4SO)(diag)-41, Inspection Mode.>.
WIRING DIAGRAM:

EN-05701

B137

5

6

7

8

2

1

9

4

3

10

22 23

11 12 13 14 15

24 25

26

16 17

18 19 20 21

27

28 29

30 31

5

3

19

B21

E2

E12

SBF-7

15A

32

49

33

47

1

2

3

4

B137

18

26

6

3

4

1

2

B47

E

1

2

B225

B21

1 2 3 4

12 13 14 15

5 6 7 8

16 17 18 19

9 10 11

20 21 22

23 24 25 26 27 28 29 30 31 32 33

35

34

37

36

39

38

41

40

43

42

44

45

47

46

49

48

51

50

53

52

54

3

4

1

2

5

6

B47

1 2 3 4

E12

9

10

1

2

3

4

5

6

7

8

11 12

14

15 16

13

18

19 20

17

22

23 24

21

38

39 40

37

34

35 36

33

30

31 32

29

26

27 28

25

B225

ECM

RELAY BLOCK

MAIN RELAY

BATTERY

IGNITION COIL

&

IGNITOR ASSY

EN(H4SO)(diag)-72

Diagnostics for Engine Starting Failure

ENGINE (DIAGNOSTICS)

Step

Check

Yes

No

1

CHECK IGNITION SYSTEM FOR SPARKS.
1) Remove the plug cord cap from each spark
plug.
2) Install a new spark plug on plug cord cap.

CAUTION:
Do not remove the spark plug from engine.
3) Contact the spark plug’s thread portion to
the engine.
4) While opening the throttle valve fully, crank
the engine to check that spark occurs at each
cylinder.

Does spark occur at each cylin-
der?

Check fuel pump
system. <Ref. to
EN(H4SO)(diag)-
74, FUEL PUMP
CIRCUIT, Diag-
nostics for Engine
Starting Failure.>

Go to step 2.

2

CHECK POWER SUPPLY CIRCUIT FOR IG-
NITION COIL AND IGNITOR ASSEMBLY.
1) Turn the ignition switch to OFF.
2) Disconnect the connector from the ignition
coil & ignitor assembly.
3) Turn the ignition switch to ON.
4) Measure the voltage between ignition coil
and ignitor assembly connector and engine
ground.

Connector & terminal

(E12) No. 2 (+) — Engine ground (–):

Is the voltage 10 V or more?

Go to step 3.

Repair the harness
and connector.

NOTE:
In this case, repair
the following item:
• Open circuit of
harness between
the ignition coil and
ignitor assembly,
and main relay
connector
• Poor contact of
coupling connector
• Blown out of fuse

3

CHECK HARNESS BETWEEN ECM AND IG-
NITION COIL AND IGNITOR ASSEMBLY.
1) Turn the ignition switch to OFF.
2) Measure the resistance between the igni-
tion coil and ignitor assembly connector and the
ECM.

Connector & terminal

(E12) No. 3 — (B137) No. 6:
(E12) No. 3 — (B137) No. 26:

Is the resistance less than 1

:? Go to step 4.

Repair the harness
and connector.

NOTE:
In this case, repair
the following item:
• Open circuit in
harness between
ECM and ignition
coil and ignitor as-
sembly connector
• Poor contact of
coupling connector

4

CHECK IGNITION COIL AND IGNITOR AS-
SEMBLY.
1) Remove the spark plug cords.
2) Measure the resistance between spark plug
cord contact portions to check secondary coil.

Terminals

No. 1 — No. 2:
No. 3 — No. 4:

Is the resistance between 10 and
15 k

:?

Go to step 5.

Replace the igni-
tion coil and ignitor
assembly. <Ref. to
IG(H4SO)-6, Igni-
tion Coil and Ignitor
Assembly.>

5

CHECK INPUT SIGNAL FOR IGNITION COIL
AND IGNITOR ASSEMBLY.
1) Connect the connector to the Ignition coil
and ignitor assembly.
2) Check if voltage varies synchronously with
engine speed when cranking, while monitoring
voltage between ignition coil and ignitor assem-
bly connector and engine ground.

Connector & terminal

(E12) No. 1 (+) — Engine ground (–):
(E12) No. 4 (+) — Engine ground (–):

Does the voltage vary 10 V or
more?

Go to step 6.

Replace the igni-
tion coil and ignitor
assembly. <Ref. to
IG(H4SO)-6, Igni-
tion Coil and Ignitor
Assembly.>

EN(H4SO)(diag)-73

Diagnostics for Engine Starting Failure

ENGINE (DIAGNOSTICS)

6

CHECK HARNESS BETWEEN ECM AND IG-
NITION COIL AND IGNITOR ASSEMBLY
CONNECTOR.
1) Turn the ignition switch to OFF.
2) Disconnect the connectors from ECM.
3) Disconnect the connector from the ignition
coil & ignitor assembly.
4) Measure the resistance of harness between
ECM and ignition coil and ignitor assembly con-
nector.

Connector & terminal

(B137) No. 18 — (E12) No. 1:
(B137) No. 19 — (E12) No. 4:

Is the resistance less than 1

:? Go to step 7.

Repair the harness
and connector.

NOTE:
In this case, repair
the following item:
• Open circuit in
harness between
ECM and ignition
coil and ignitor as-
sembly connector
• Poor contact of
coupling connector

7

CHECK HARNESS BETWEEN ECM AND IG-
NITION COIL AND IGNITOR ASSEMBLY
CONNECTOR.
Measure the resistance of harness between
ECM and engine ground.

Connector & terminal:

(B137) No. 18 — Engine ground:
(B137) No. 19 — Engine ground:

Is the resistance 1 M

: or

more?

Repair the poor
contact of ECM
connector.

Repair the ground
short circuit of har-
ness between
ECM and ignition
coil and ignitor
assembly connec-
tor.

Step

Check

Yes

No

EN(H4SO)(diag)-74

Diagnostics for Engine Starting Failure

ENGINE (DIAGNOSTICS)

E: FUEL PUMP CIRCUIT

CAUTION:
After repair or replacement of faulty parts, perform Clear Memory Mode <Ref. to EN(H4SO)(diag)-50,
OPERATION, Clear Memory Mode.>, and Inspection Mode <Ref. to EN(H4SO)(diag)-41, PROCEDURE,
Inspection Mode.>.
WIRING DIAGRAM:

Step

Check

Yes

No

1

CHECK OPERATING SOUND OF FUEL
PUMP.
Make sure that the fuel pump operates for two
seconds when turning the ignition switch to ON.

NOTE:
Fuel pump operation can be executed using the
Subaru Select Monitor.
For the procedures, refer to “Compulsory Valve
Operation Check Mode”. <Ref. to
EN(H4SO)(diag)-51, Compulsory Valve Opera-
tion Check Mode.>

Does the fuel pump emit oper-
ating sound?

Check the fuel
injector circuit.
<Ref. to
EN(H4SO)(diag)-
76, FUEL INJEC-
TOR CIRCUIT,
Diagnostics for
Engine Starting
Failure.>

Go to step 2.

EN-06832

5

3

B97

MAIN SBF

No. 12

SBF-6

E

3

1

B72

B362

B136

No. 11

FUEL PUMP
RELAY

FUEL PUMP

FUEL PUMP

CONDENSER

ECM

BATTERY

IGNITION
SWITCH

B136

B72

1

3

4 5 6

2

R142

R58

5
6

7 8

3
4

1 2

B362

1
2

1
2

R58

M

6

5

E

R142

2

1

B97

R1

20

R67

R46

12

R67

1

2

3 4 5 6

1 2 3 4

5 6 7 8 9

10 11 12 13 14 15 16 17 18 19 20

1
4
3
2

16

10 11 12 13 14 15

25

24

30

9

8

7

17 18 19 20
28

21 22 23

29

32

31

1

2

3

4

5

6

27

26

33 34 35

: SEDAN MODEL

:

SD

SD

SD

1 2
3 4
5 6