Subaru Crosstrek (2019 year). Instruction — part 20

(313,1)

北米Model "A1340BE-A" EDITED: 2018/ 4/ 2

&

To activate/deactivate the Hill
start assist system

Hill start assist OFF indicator

CAUTION

When starting on an up hill grade,
make sure the Hill start assist OFF
indicator light is off.

If the Hill start assist OFF indicator
light is on, make sure the parking
brake is applied.

To activate or deactivate the Hill start
assist system, perform the following steps.

NOTE

If you make an error when performing
any steps in the following procedure,

place the ignition switch in the “LOCK”/
“OFF” position once and then start
over again.

!

To deactivate

1. Park your vehicle in a flat and safe
location and apply the parking brake.
2. Turn the ignition switch to the “LOCK”/
“OFF” position.
3. Restart the engine.

4. Confirm the following items.

(1) The brake system warning light
illuminates.
(2) The Vehicle Dynamics Control
warning light turns off.
(3) The Vehicle Dynamics Control
OFF indicator light turns off.
(4) The ABS warning light turns off.

5. Press and hold the Vehicle Dynamics
Control OFF switch for 30 seconds until
the Vehicle Dynamics Control OFF indica-
tor light

on the combination meter turns

on and off.
6. Within 5 seconds, release the Vehicle
Dynamics Control OFF switch.
7. Within 2 seconds, press back the
Vehicle Dynamics Control OFF switch.
The Hill start assist OFF indicator light
turns on and off.
8. Turn the ignition switch to the “LOCK”/
“OFF” position. Hill start assist is deacti-
vated.

NOTE

When the Hill start assist system is
deactivated, the Hill start assist OFF

– CONTINUED –

Starting and operating/Hill start assist system

7-47

7

(314,1)

北米Model "A1340BE-A" EDITED: 2018/ 4/ 2

indicator light illuminates.

!

To reactivate

To reactivate Hill start assist system,
repeat steps 1 to 8. When the Hill start
assist system is activated, the Hill start
assist OFF indicator light turns off.

&

Hill start assist warning light/
Hill start assist OFF indicator
light

Refer to “Hill start assist warning light/Hill
start assist OFF indicator light” F3-22.

Cruise control (if equipped)

NOTE

For models with EyeSight system:
Refer to the Owner’s Manual supple-
ment for the EyeSight system.

Cruise control enables you to maintain a
constant vehicle speed without holding
your foot on the accelerator pedal and it is
operative when the vehicle speed is 20
mph (30 km/h) or more.

WARNING

.

Do not use the cruise control

under any of the following condi-
tions. These may cause loss of
vehicle control.

– driving up or down a steep

grade

– driving on slippery or winding

roads

– driving in heavy traffic

– towing a trailer

.

When using the cruise control,

always set the speed appropri-
ately according to the speed limit,
traffic flow, road conditions, and
other conditions.

NOTE

Make sure the cruise control system is
turned off when the cruise control is not
in use to avoid unintentionally setting
of the cruise control.

&

To set cruise control

Cruise control main button

1. Press the cruise control main button.

Starting and operating/Cruise control

7-48

(315,1)

北米Model "A1340BE-A" EDITED: 2018/ 4/ 2

Cruise control indicator light (type A)

Cruise control indicator light (type B)

The cruise control indicator light on the
combination meter will illuminate.
2. Depress the accelerator pedal until the
vehicle reaches the desired speed.

3. Press the “RES/SET” switch to the
“SET” side and release it. Then release the
accelerator pedal.

NOTE

When setting a cruise speed for the first
time during a drive, both “SET” and
“RES” may be used to set the initial
cruise speed.

Cruise control set indicator light (type A)
1)

When setting the displayed unit as
“MPH”.

2)

When setting the displayed unit as
“km/h”.

– CONTINUED –

Starting and operating/Cruise control

7-49

7

(316,1)

北米Model "A1340BE-A" EDITED: 2018/ 4/ 2

Cruise control set indicator light (type B)
1)

When setting the displayed unit as
“MPH”.

2)

When setting the displayed unit as
“km/h”.

At this time, the cruise control set indicator
light is illuminated in the combination
meter. The set speed will be shown on
the combination meter. You can change
the displayed unit by operating the combi-
nation meter display.

.

For type A meter details, refer to

“Combination meter settings” F3-11.
.

For type B meter details, refer to

“Screen Settings” F3-38.

The vehicle will maintain the desired
speed.

Vehicle speed can be temporarily in-

creased while driving with the cruise
control activated. Simply depress the
accelerator pedal to accelerate the vehi-
cle. When the accelerator pedal is re-
leased, the vehicle will return to and
maintain the previous cruising speed.

&

To temporarily cancel the
cruise control

The cruise control can be temporarily
canceled in the following ways.

.

Press the “CANCEL” button.

.

Press the X-MODE switch to activate

the X-MODE (models with X-MODE).
.

Depress the brake pedal.

.

Depress the clutch pedal (MT models

only).

WARNING

For CVT models, you can cancel the
cruise control by shifting the select
lever into the “N” position. However,
do not shift the lever into the “N”
position while driving except in case
of emergency. If the select lever is
shifted into the “N” position, the
engine brake will no longer work.
This could result in an accident.

The cruise control set indicator light in the
combination meter turns off when the
cruise control is canceled.

To resume the cruise control after it has
been temporarily canceled and with vehi-
cle speed of approximately 20 mph (30
km/h) or more, press the “RES/SET”

Starting and operating/Cruise control

7-50

(317,1)

北米Model "A1340BE-A" EDITED: 2018/ 4/ 2

switch to the “RES” side to return to the
original cruising speed automatically.
The cruise control set indicator light in the
combination meter will automatically illu-
minate at this time.

&

To turn off the cruise control

There are two ways to turn off the cruise
control:
.

Press the cruise control main button

again.
.

Turn the ignition switch to the “ACC” or

“LOCK”/“OFF” position (but only when the
vehicle is completely stopped).

&

To change the cruising speed

!

To increase the speed (by the “RES/
SET” switch)

Press the “RES/SET” switch to the “RES”
side and hold it until the vehicle reaches
the desired speed. Then, release the
switch. The vehicle speed at that moment
will be memorized and treated as the new
set speed.

When setting the displayed unit as
“MPH”:
The set speed can be increased 1 mph
(1.6 km/h) each time by pressing the “RES/
SET” switch to the “RES” side.

When setting the displayed unit as
“km/h”:
The set speed can be increased 1 km/h
each time by pressing the “RES/SET”
switch to the “RES” side.

!

To increase the speed (by accelera-
tor pedal)

1. Depress the accelerator pedal to ac-
celerate the vehicle to the desired speed.

2. Press the “RES/SET” switch to the
“SET” side once. Now the desired speed is
set and the vehicle will keep running at that
speed without depressing the accelerator
pedal.

– CONTINUED –

Starting and operating/Cruise control

7-51

7

(318,1)

北米Model "A1340BE-A" EDITED: 2018/ 4/ 2

!

To decrease the speed (by the “RES/
SET” switch)

Press the “RES/SET” switch to the “SET”
side and hold it until the vehicle reaches
the desired speed. Then, release the
switch. The vehicle speed at that moment
will be memorized and treated as the new
set speed.

When setting the displayed unit as
“MPH”:
The set speed can be decreased 1 mph
(1.6 km/h) each time by pressing the “RES/
SET” switch to the “SET” side.

When setting the displayed unit as
“km/h”:
The set speed can be decreased 1 km/h
each time by pressing the “RES/SET”
switch to the “SET” side.

!

To decrease the speed (by brake
pedal)

1. Depress the brake pedal to release
cruise control temporarily.

2. When the speed decreases to the
desired speed, press the “RES/SET”
switch to the “SET” side once. Now the
desired speed is set and the vehicle will
keep running at that speed without depres-
sing the accelerator pedal.

&

Cruise control indicator light

Refer to “Cruise control indicator light” F3-
30.

&

Cruise control set indicator
light

Refer to “Cruise control set indicator light”
F3-31.

Starting and operating/Cruise control

7-52

(319,1)

北米Model "A1340BE-A" EDITED: 2018/ 4/ 2

BSD/RCTA (if equipped)

The BSD/RCTA consists of rear radar with
Blind Spot Detection and Rear Cross
Traffic Alert.

These functions enable the system to
detect objects or vehicles to the rear,
drawing attention to the driver when
changing a lane or when driving in reverse.

WARNING

The driver is responsible for driving
safely. Always be sure to check the
surroundings with your eyes when
changing lanes or reversing the
vehicle.

The system is designed to assist the
driver to change lanes or reverse
safely by monitoring the rear and
side areas of the vehicle. However,
you cannot rely on this system alone
in assuring the safety during a lane
change or reversing. Overconfi-
dence in this system could result in
an accident and lead to serious
injury or death. Since the system
operation has various limitations,
the flashing or illumination of the
BSD/RCTA approach indicator light
may be delayed or it may not operate

at all even when a vehicle is present
in a neighboring lane or approach-
ing from either side.

The driver is responsible for paying
attention to the rear and side areas
of the vehicle.

&

System features

BSD/RCTA consists of the following func-
tions.
.

To detect a vehicle in a blind spot on an

adjacent lane or a vehicle approaching at
high speed while driving the vehicle (Blind
Spot Detection)
.

To detect a vehicle approaching from

the right or left while reversing the vehicle
(Rear Cross Traffic Alert)

The system uses radar sensors for the
above functions.

NOTE

The BSD/RCTA radar sensor has been
certified by the radio wave related laws
of the U.S. and Canada. When driving in
other countries, certification of the
country where the vehicle is driven
must be obtained. For certification in
the U.S. and Canada, refer to “Certifica-
tion for the BSD/RCTA” F7-60.

!

Blind Spot Detection (BSD)

1)

Operating range

The system warns the driver of dangers as
follows.
.

If the system detects a vehicle existing

in the blind spot, the BSD/RCTA approach
indicator light(s) on the outside mirror(s)
will illuminate.

– CONTINUED –

Starting and operating/BSD/RCTA

7-53

7

(320,1)

北米Model "A1340BE-A" EDITED: 2018/ 4/ 2

BSD/RCTA approach indicator light

.

If the driver operates the turn signal

lever in the direction which the BSD/RCTA
approach indicator light is illuminating, the
corresponding BSD/RCTA approach indi-
cator light will flash.

!

Lane Change Assist (LCA)

1)

Operating range

The system warns the driver of dangers as
follows.
.

If the system detects a vehicle ap-

proaching at a high speed in the neighbor-
ing lanes, the BSD/RCTA approach indi-
cator light(s) on the outside mirror(s) will
illuminate.
.

If the driver operates the turn signal

lever in the direction which the BSD/RCTA
approach indicator light is illuminating, the
corresponding BSD/RCTA approach indi-
cator light will flash.

!

Rear Cross Traffic Alert (RCTA)

1)

Operating range

The system notifies the driver of another
vehicle approaching from either side when
driving in reverse. This feature helps the
driver check the rear and side areas of the
vehicle when moving backward.

If the system detects a vehicle approach-
ing from either side while moving back-
ward, it warns the driver of dangers in the
following way.
.

The BSD/RCTA approach indicator

light(s) on the outside mirror(s) flashes.
.

A warning buzzer sounds.

.

An icon appears on the rear view

camera screen (audio/navigation monitor)

Starting and operating/BSD/RCTA

7-54

(321,1)

北米Model "A1340BE-A" EDITED: 2018/ 4/ 2

!

Limitations of the detectability of
RCTA

Since the detectability of RCTA is limited,
the RCTA may not operate properly in
angled parking.

Example 1
1)

The detection range of the radar sensors

2)

Area out of detection range of the radar
sensors

A)

Vehicle that may not be detected

B)

Parked vehicle

WARNING

An approaching vehicle (A) may not
be detected because the detection
range is limited by the parked vehi-
cle (B). Always be sure to check the
surroundings with your eyes when

reversing the vehicle.

Example 2
1)

The detection range of the radar sensors

C)

Vehicle that may be detected

NOTE

The system may detect that a vehicle
(C) is passing in front of your vehicle.
Always be sure to check the surround-
ings with your eyes when reversing the
vehicle.

&

System operation

!

Operating conditions

The BSD/RCTA will operate when all of the
following conditions are met.
.

The ignition switch is in the “ON”

position.
.

The BSD/RCTA warning indicator and

BSD/RCTA OFF indicator are turned off.
.

The vehicle is driven at speeds above 7

mph (12 km/h) (except when reversing).
.

The shift lever/select lever is in the “R”

position (when reversing).

The BSD/RCTA will not operate in the
following situations.
.

The BSD/RCTA OFF indicator is on.

.

The vehicle speed is below 7 mph (12

km/h) even when the BSD/RCTA OFF
indicator remains off (except when rever-
sing).

NOTE

.

In the following case, the BSD/RCTA

will stop operating and the BSD/RCTA
warning indicator will appear. If the
BSD/RCTA warning indicator appears,
have your vehicle inspected at a
SUBARU dealer as soon as possible.

– When a malfunction occurs in the
system, including the BSD/RCTA
approach indicator light

– CONTINUED –

Starting and operating/BSD/RCTA

7-55

7

(322,1)

北米Model "A1340BE-A" EDITED: 2018/ 4/ 2

.

In the following cases, the BSD/

RCTA will temporarily stop operating
(or may stop operating) and the BSD/
RCTA OFF indicator will appear.

– When the radar sensor becomes
significantly misaligned (If the or-
ientation of the radar sensor is
shifted for any reason, readjust-
ment is required. Have the sensor
adjusted at a SUBARU dealer.)
– When a large amount of snow or
ice sticks to the rear bumper sur-
face around the radar sensors
– When the vehicle is driven on a
snow-covered road or in an envir-
onment in which there are no ob-
jects around (such as in a desert) for
a long time
– When the temperature around the
radar sensors increased exces-
sively due to long driving on uphill
grades in summer, etc.
– When the temperature around the
radar sensors becomes extremely
low
– When the vehicle battery voltage
lowers
– When the vehicle battery be-
comes overvoltage

When the above conditions are cor-
rected, the BSD/RCTA will resume op-

eration and the BSD/RCTA OFF indica-
tor will disappear. However, if the BSD/
RCTA OFF indicator has appeared for a
prolonged time, have the system in-
spected at a SUBARU dealer as soon as
possible.
.

The detectability of the radar sen-

sors is restricted. The BSD/RCTA de-
tection may be impaired and the system
may not operate properly under the
following conditions.

– When the rear bumper around the
radar sensors is distorted
– When ice, snow or mud adheres
to the rear bumper surface around
the radar sensors
– When stickers, etc. are affixed on
the areas of the radar sensors on
the rear bumper
– During adverse weather condi-
tions such as rain, snow or fog
– When driving on wet roads such
as snow-covered roads and through
puddles

.

The radar sensors may not detect or

may have difficulty detecting the fol-
lowing.

– Small motorcycles, bicycles, pe-
destrians, stationary objects on the
road or road side, etc.
– Vehicles with body shapes that
the radar may not reflect (vehicles

with a low body height such as
sports cars or a trailer with no
cargo)
– Vehicles that are not approaching
your vehicle even though they are in
the detection area (either on a
neighboring lane to the rear or be-
side your vehicle when reversing)
(The system determines the pre-
sence of approaching vehicles
based on data detected by the radar
sensors.)
– Vehicles traveling at significantly
different speeds
– Vehicles driving in parallel at al-
most the same speed as your vehi-
cle for a prolonged time
– Oncoming vehicles
– Vehicles in a lane beyond the
neighboring lane
– Vehicles travelling at a signifi-
cantly lower speed that you are
trying to overtake

.

On a road with extremely narrow

lanes, the system may detect vehicles
driving in a lane next to the neighboring
lane.
.

When the 8-inch audio/navigation

system is performing a software up-
date, the RCTA warning icons may not
be displayed on the audio/navigation
screen until the update is complete.

Starting and operating/BSD/RCTA

7-56

(323,1)

北米Model "A1340BE-A" EDITED: 2018/ 4/ 2

&

BSD/RCTA approach indica-
tor light/warning buzzer

When the BSD/RCTA is active, the BSD/
RCTA approach indicator light will operate
to alert the driver when there are vehicles
in the neighboring lanes. When reversing
the vehicle, the BSD/RCTA approach
indicator light and warning buzzer will
operate to alert the driver that a vehicle is
approaching from the left or right side.

!

BSD/RCTA approach indicator light

BSD/RCTA approach indicator light

It is mounted in each side of the outside
mirrors.
The indicator light will illuminate when a
vehicle approaching from behind is de-
tected.
The indicator light will flash to warn the

driver of dangers under the following
conditions.
.

While the indicator light illuminates, if

you operate the turn signal lever toward
the side in which this light turned on.
.

When reversing the vehicle while the

system detects a vehicle approaching
from either side.

!

BSD/RCTA approach indicator
light dimming function

When the headlights are turned on, the
brightness of the BSD/RCTA approach
indicator light will be reduced.

NOTE

.

You may have difficulty recognizing

the BSD/RCTA approach indicator light
under the following conditions.

– When affected by direct sunlight
– When affected by the headlight
beams from the vehicles behind

.

While the illumination brightness

control dial is in the fully upward
position, even if the headlights are
turned on, the brightness of the BSD/
RCTA approach indicator light will not
be reduced. For details about the
illumination brightness control dial,
refer to “Illumination brightness con-
trol” F3-12.

!

BSD/RCTA approach warning buz-
zer (only when reversing)

A warning buzzer sounds along with
flashing of the BSD/RCTA approach in-
dicator light to warn the driver of dangers.

The setting of the warning buzzer volume
can be changed by operating the combi-
nation meter display (color LCD). For
details, refer to “Menu screens” F3-38.

!

Safety tips regarding the BSD/RCTA
approach indicator light/warning
buzzer

.

In the following cases, operation of the

BSD/RCTA approach indicator light and
the warning buzzer may be delayed or the
system may fail to issue these warnings.

– When a vehicle moves to the neigh-
boring lane from a lane next to the
neighboring lane
– When driving on a steep incline or
on repeated sharp uphill and downhill
grades
– When going beyond a pass
– When both your vehicle and a
vehicle driving on a neighboring lane
are driving on the far side of each lane.
– When several narrowly-spaced ve-
hicles are approaching in a row
– In low radius bends (tight bends or
when making turns at an intersection)

– CONTINUED –

Starting and operating/BSD/RCTA

7-57

7

(324,1)

北米Model "A1340BE-A" EDITED: 2018/ 4/ 2

– When there is a difference in height
between your lane and the neighboring
lane
– Immediately after the BSD/RCTA is
activated by pressing the BSD/RCTA
OFF switch
– Immediately after the shift lever/
select lever is shifted to the “R” position
– When extremely heavy cargo is
loaded in the cargo area

.

During reversing, operation of the BSD/

RCTA approach indicator light and the
warning buzzer may be delayed or the
system may fail to issue these warnings
under the following conditions.

– When backing out of an angled
parking space
– When a large-sized vehicle is
parked next to your vehicle (That
vehicle prevents the propagation of
radar waves.)
– When reversing on sloped roads
– When reversing at a high speed

.

The BSD/RCTA approach indicator

light may illuminate when driving close to
solid objects on the road or road side (such
as guardrails, tunnels and sidewalls).
.

The BSD/RCTA approach indicator

light may flash when turning at an inter-
section in urban areas or a multilane
intersection.
.

The BSD/RCTA approach indicator

light may flash and the warning buzzer
may sound if a building or a wall exists in
the reversing direction.
.

In the following cases, the system may

detect a vehicle driving two lanes away
from your vehicle.

– When you are driving on the near
side of its lane from the corresponding
vehicle
– When the vehicle driving two lanes

away is driving on the near side of its
lane from your vehicle

&

BSD/RCTA OFF indicator

!

System temporary stops

1)

BSD/RCTA temporary stop message

2)

BSD/RCTA OFF indicator

This display appears when the system is
used under the following conditions.
.

Extremely high or low temperatures

.

When abnormal voltage exists for the

vehicle battery
.

When the radar sensor is significantly

misaligned

Once the above conditions are corrected,
the system will recover from the temporary
stop condition and the indicator will dis-

Starting and operating/BSD/RCTA

7-58

(325,1)

北米Model "A1340BE-A" EDITED: 2018/ 4/ 2

appear. If the indicator remains displayed
for a prolonged time, have the system
inspected at a SUBARU dealer.

!

System temporary stops due to
reduced radar sensitivity

1)

BSD/RCTA temporary stop message due
to reduced radar sensitivity

2)

BSD/RCTA OFF indicator

This display appears when the detectabil-
ity of the radar sensors is reduced. Once
the condition is corrected, the system will
recover from the temporary stop condition
and the indicator will disappear. If the
indicator remains displayed for a pro-
longed time, have the system inspected
at a SUBARU dealer.

&

BSD/RCTA warning indicator

!

System malfunction

1)

BSD/RCTA malfunction message

2)

At first, this message will appear

3)

Then this message will appear

4)

BSD/RCTA warning indicator

This display appears when a malfunction
occurs in the system. Contact a SUBARU
dealer and have the system inspected.

&

BSD/RCTA OFF switch

BSD/RCTA OFF switch

BSD/RCTA OFF indicator (type A)

– CONTINUED –

Starting and operating/BSD/RCTA

7-59

7

(326,1)

北米Model "A1340BE-A" EDITED: 2018/ 4/ 2

BSD/RCTA OFF indicator (type B)

If the BSD/RCTA OFF switch is pressed,
the BSD/RCTA OFF indicator appears on
the combination meter, and the BSD/
RCTA is deactivated.
Press the switch again to activate the BSD/
RCTA. The BSD/RCTA OFF indicator will
disappear.
When this occurs, the BSD/RCTA ap-
proach indicator light on the side of the
rearview mirror illuminates for a few
seconds and then turns off.

NOTE

.

In the following cases, the system

may not operate properly due to
blocked radar waves. Press the BSD/
RCTA OFF switch to deactivate the
system.

– When towing a trailer
– When a bicycle carrier or other
carrier item is fitted to the rear of the
vehicle
– When using a chassis dynam-
ometer or free roller device, etc.
– When running the engine and
making the wheels rotate while
lifting up the vehicle

.

If the ignition switch is turned to the

“LOCK”/“OFF” position, the last known
status of the system is maintained. For
example, if the ignition switch is turned
to the “LOCK”/“OFF” position with the
BSD/RCTA deactivated, the BSD/RCTA
will remain deactivated the next time
the ignition switch is turned to the “ON”
position.

&

Certification for the BSD/
RCTA

!

U.S.-spec. models

FCC ID: OAYSRR3A

CAUTION

FCC WARNING

Changes or modifications not ex-
pressly approved by the party re-
sponsible for compliance could void
the user’s authority to operate the
equipment.

NOTE

This device complies with part 15 of the
FCC Rules. Operation is subject to the
following two conditions: (1) This de-
vice may not cause harmful interfer-
ence, and (2) this device must accept
any interference received, including
interference that may cause undesired
operation.

Starting and operating/BSD/RCTA

7-60

(327,1)

北米Model "A1340BE-A" EDITED: 2018/ 4/ 2

!

Canada-spec. models

!

Mexico-spec. models

– CONTINUED –

Starting and operating/BSD/RCTA

7-61

7

(328,1)

北米Model "A1340BE-A" EDITED: 2018/ 4/ 2

&

Handling of radar sensors

1)

Sensors

The radar sensors, one on each side of the
vehicle, are mounted inside the rear
bumper.
To ensure correct operation of the BSD/
RCTA, observe the following precautions.
.

Always keep the bumper surface near

the radar sensors clean.
.

Do not affix any stickers or other items

on the bumper surface near the radar
sensors.
.

Do not modify the bumper near the

radar sensors.
.

Do not paint the bumper near the radar

sensors.
.

Do not expose the bumper near the

radar sensors to strong impacts. If a

sensor becomes misaligned, a system
malfunction may occur, including the in-
ability to detect vehicles entering the
detection areas. If any strong shock is
applied to the bumper, be sure to contact
your SUBARU dealer for inspection.
.

Do not disassemble the radar sensors.

NOTE

If the radar sensors require repair or
replacement, or the bumper area
around the radar sensors requires
repair, paintwork or replacement, con-
tact your SUBARU dealer for assis-
tance.

Reverse Automatic Braking
System (if equipped)

Reverse Automatic Braking is a system
designed to help avoid collisions or reduce
collision damage when reversing the
vehicle. If a wall or an obstacle is detected
in the reversing direction, the system will
notify the driver with a warning sound and
may activate the vehicle’s brakes auto-
matically.

WARNING

.

Reverse Automatic Braking is not

a system intended to replace the
driver’s responsibility to check
surrounding areas for vehicles or
obstacles to avoid a collision.

.

The driver is responsible for driv-

ing safely. Always be sure to
check the surroundings visually
when reversing the vehicle.

.

There are some cases in which

the vehicle cannot avoid colli-
sion, because the system opera-
tion has limitations. The warning
sound or automatic braking may
be delayed or may not operate at
all even when an obstacle is
present.

Starting and operating/Reverse Automatic Braking System

7-62