Subaru Impreza 3 / Impreza WRX / Impreza WRX STI. Manual — part 392

CS-19

MT Gear Shift Lever

CONTROL SYSTEMS

2. EXCEPT FOR STI MODEL

NOTE:

• Clean all the parts before assembly.

• Apply NIGTIGHT LYW No. 2 grease or equiva-

lent to each part. <Ref. to CS-4, 5MT GEAR SHIFT

LEVER, COMPONENT, General Description.>

1) Mount the bushing and cushion rubber to the

stay.

2) Install the bushing and spacer to boss.

3) Using new self-locking nuts, install the boss to

the joint.
Tightening torque:

12 N·m (1.2 kgf-m, 8.9 ft-lb)

4) Install the snap ring to gear shift lever and install

the bushing.
NOTE:

Apply grease to the bushing.

5) Apply grease to the bushing and O-ring, and

then install to gear shift lever.

6) Apply sufficient grease into boss, and then install

the gear shift lever to the stay.

(A) Bushing
(B) Cushion rubber

(A) Bushing
(B) Spacer

CS-00061

(A)

(B)

CS-00238

(B)

(A)

(A)

CS-00322

(A) Spring pin
(B) Bushing

(C) Snap ring

(A) O-ring
(B) Bushing

CS-01414

(B)

(A)

(C)

CS-01415

(B)

(A)

(A)

CS-01413

CS-20

MT Gear Shift Lever

CONTROL SYSTEMS

7) Install the snap ring.

8) Insert the gear shift lever and rod into boot hole.

9) Install the rod.
Tightening torque:

12 N·m (1.2 kgf-m, 8.9 ft-lb)

10) Install a new lock wire.

NOTE:

• Install the lock wire to the stay groove.

• Bend the extra wire to the same direction of lock

wire winding.

(A) Snap ring

(A) Rod
(B) Lever

(C) Stay

CS-00318

(A)

CS-00317

(A)

(B)

(C)

(A) Lock wire

(A) Inner boot
(B) Lock wire

(C) Stay

CS-00316

(A)

CS-00240

(A)

(A)

(B)

(B)

B

B

(B)

B - B

(C)

CS-21

MT Gear Shift Lever

CONTROL SYSTEMS

E: INSPECTION

1) Check the parts (bushing, cushion rubber, spac-

er, boot, stay and rod, etc.) for deformation, dam-

age and wear. If necessary, correct or replace

faulty parts. Compare the removed parts with new

parts to judge if there are damages or not.

• STI model

• Except for STI model

(A) Bushing
(B) Cushion rubber

(C) Spacer
(D) Boot

(E) Stay

(F) Rod

CS-00921

(A)

(C)

(A)

(C)

(F)

(A)

(D)

(B)

(E)

(C)

(A) Bushing
(B) Cushion rubber

(C) Spacer
(D) Boot

(E) Stay

(F) Rod

CS-01045

(C)

(D)

(A)

(F)

(A)

(E)

(C)

(A)

(B)

(C)

CS-22

MT Gear Shift Lever

CONTROL SYSTEMS

2) Check the swing torque of rod linked with the

gear shift lever.

If the torque exceeds the specifications, replace the

bushing or retighten nuts.
Swing torque:

3.7 N (0.38 kgf, 0.83 lbf) or less

• STI model

• Except for STI model

(A) Pivot
(B) Swing torque

(A) Pivot
(B) Swing torque

CS-00116

(A)

(B)

CS-00116

(A)

(B)