Subaru Impreza 3 / Impreza WRX / Impreza WRX STI. Manual — part 210

1) On «System Operation Check Mode» display,

select {Fuel Pump Control}.

2) On «Fuel Pump Control» display, select {OFF

Drive}.

3) On «Start the Engine» display, start the engine

and click the [OK] button.

4) On «OFF Drive» display, click the [Execution]

button and execute the OFF drive.

5) Click the [Cancel] button to stop the OFF drive.

6) Click the [ Exit] button to end the OFF drive.

The screen will return to the «Fuel Pump Control»

screen.
NOTE:

For detailed operation procedures, refer to “PC ap-

plication help for Subaru Select Monitor”.

2. FUEL PUMP CONTROL (ON/OFF DRIVE)

CAUTION:

1) On «System Operation Check Mode» display,

select {Fuel Pump Control}.

2) On «Fuel Pump Control» display, select {ON/

OFF Dr.}.

3) On «Turn Ignition Switch ON with Engine OFF»

display, turn the ignition switch to ON and click the

[OK] button.

4) On «ON/OFF Dr.» display, click the [Execution]

button and execute the ON/OFF drive.

5) Click the [Cancel] button to stop the ON/OFF

drive.

EN-05692

EN-06148

Display

Actuator ON/OFF Operation
Immobilizer System
Fuel Pump Control
Fixed Idle Ignition Timing
Idle Speed Control
Injector Control

EN(H4DOTC)(diag)-66

System Operation Check Mode

ENGINE (DIAGNOSTICS)

6) Click the [ Exit] button to end the ON/OFF

drive. The screen will return to the «Fuel Pump

Control» screen.
NOTE:

For detailed operation procedures, refer to “PC ap-

plication help for Subaru Select Monitor”.

3. IDLING IGNITION TIMING FIXED

CAUTION:

1) On «System Operation Check Mode» display,

select {Fixed Idle Ignition Timing}.

2) On «Start the Engine» display, start the engine

and click the [OK] button.

3) On «Fixed Idle Ignition Timing» display, click the

[Execution] button and execute the idling ignition

timing fixed.

4) Click the [Cancel] button to stop the idling igni-

tion timing fixed.

5) Click the [ Exit] button to end the idle ignition

timing fixed. The screen will return to the «System

Operation Check Mode» screen.
NOTE:

For detailed operation procedures, refer to “PC ap-

plication help for Subaru Select Monitor”.

4. IDLE SPEED CONTROL

CAUTION:

1) On «System Operation Check Mode» display,

select {Idle Speed Control}.

2) On «Start the Engine» display, start the engine

and click the [OK] button.

3) In the «Idle Speed Control» display, click the [ ]

button or the [ ] button to change the setting val-

ues, then click the [OK] button.

Setting is possible in a range between 500 rpm —

2,000 rpm, in increments of 50 rpm. However, the

engine speed that can actually be controlled will

vary depending on the vehicle.

4) Click the [Cancel] button to stop the idle speed

control.

5) Click the [ Exit] button to end the idle speed

control. The screen will return to the «System Op-

eration Check Mode» screen.
NOTE:

For detailed operation procedures, refer to “PC ap-

plication help for Subaru Select Monitor”.

5. INJECTOR CONTROL (INJECTION STOP

MODE)

CAUTION:

1) On «System Operation Check Mode» display,

select {Injector Control}.

2) On «Injector Control» display, select {Injection

Stop Mode}.

3) On «Injection Stop Mode» display, select the

fuel injector to be stopped.

4) On «Start the Engine» display, start the engine

and click the [OK] button.

5) On «Fuel Injector #» display, click the [Execu-

tion] button and execute the injection stop mode.

6) Click the [Cancel] button to stop the injection

stop mode.

7) Click the [ Exit] button to return the «Injection

Stop Mode» display screen.

8) On the «Injection Stop Mode» display, click the

[Return] button to end the «Injection Stop Mode».

The screen will return to the «Injector Control»

screen.
NOTE:

For detailed operation procedures, refer to “PC ap-

plication help for Subaru Select Monitor”.

6. INJECTOR CONTROL (INJECTION

QUANTITY CONTROL)

CAUTION: