Subaru Impreza 3 / Impreza WRX / Impreza WRX STI. Manual — part 721

SL-33

Rear Inner Remote

SECURITY AND LOCKS

8. Rear Inner Remote

A: REMOVAL

Refer to “Front Inner Remote” for the removal pro-

cedure. <Ref. to SL-30, REMOVAL, Front Inner

Remote.>

B: INSTALLATION

Install each part in the reverse order of removal.

C: INSPECTION

Check if the rear remote handle operates normally.

• If the lever is faulty, replace the rear inner remote

handle.

• If the cable is deformed, replace the rear door

latch and door lock actuator assembly.

SL-34

Rear Outer Handle

SECURITY AND LOCKS

9. Rear Outer Handle

A: REMOVAL

1) Raise the rear door glass to the top position.

2) Remove the rear door trim. <Ref. to EI-45, RE-

MOVAL, Door Trim.>

3) Remove the sealing cover. <Ref. to EB-24, RE-

MOVAL, Rear Sealing Cover.>

4) Remove the screws, and move aside the rear

door latch and door lock actuator assembly.

5) Remove the child protector cover, and loosen

the TORX

®

bolt.

6) Remove the outer handle cover.

7) Move the rear outer handle towards the rear,

and remove the rear outer handle.
CAUTION:

Do not apply excessive force to remove the

handle from the door panel. The door panel

may become deformed.

8) Remove the outer spacer, and remove the frame

assembly from the inner side.

9) Remove the TORX

®

bolt.

10) Remove the frame assembly from inside the

door panel.

B: INSTALLATION

Install each part in the reverse order of removal.
Tightening torque:

Refer to “COMPONENT” of “General Descrip-

tion”. <Ref. to SL-2, DOOR LOCK ASSEM-

BLY, COMPONENT, General Description.>

C: INSPECTION

Check if the rear outer handle operates normally.

• If the lever is faulty, replace the rear outer han-

dle.

• If the rod is deformed, replace the rear door latch

and door lock actuator assembly.

SL-00738

SL-00739

SL-00737

SL-35

Rear Door Latch and Door Lock Actuator Assembly

SECURITY AND LOCKS

10.Rear Door Latch and Door

Lock Actuator Assembly

A: REMOVAL

1) Disconnect the ground cable from battery.

2) Remove the rear door trim. <Ref. to EI-45, RE-

MOVAL, Door Trim.>

3) Remove the wire from the rear inner remote.

<Ref. to SL-33, REMOVAL, Rear Inner Remote.>

4) Remove the sealing cover. <Ref. to EB-24, RE-

MOVAL, Rear Sealing Cover.>

5) Remove the rear door glass. <Ref. to GW-21,

REMOVAL, Rear Door Glass.>

6) Disconnect the door lock actuator connector.

7) Remove the screws, and remove the rear door

latch and door lock actuator assembly.

B: INSTALLATION

Install each part in the reverse order of removal.
Tightening torque:

Refer to “COMPONENT” of “General Descrip-

tion”. <Ref. to SL-2, DOOR LOCK ASSEM-

BLY, COMPONENT, General Description.>

NOTE:

Make sure the child safety lock works correctly af-

ter installation.

C: INSPECTION

1. DOOR LATCH

Check if the rear door latch operates normally.

• If the cable or rod is faulty, replace the rear door

latch and door lock actuator assembly.

2. LOCK ACTUATOR

1) Disconnect the ground cable from battery.

2) Disconnect the door lock actuator harness con-

nector.

3) Connect the battery to door lock actuator termi-

nals.

4) If the actuator does not operate normally, re-

place the rear door latch & door lock actuator as-

sembly.

SL-00738

Actuator operation

Terminals

No. 1

No. 2

Lock → Unlock

–

+

Unlock → Lock

+

–

2 1

SL-00765

SL-36

Rear Gate Opener Button

SECURITY AND LOCKS

11.Rear Gate Opener Button

A: REMOVAL

1) Disconnect the ground cable from battery.

2) Remove the rear gate trim. <Ref. to EI-69, RE-

MOVAL, Rear Gate Trim.>

3) Remove the rear gate garnish. <Ref. to EI-72,

REMOVAL, Rear Gate Garnish.>

4) Disconnect the harness connector of the rear

gate opener button.

5) Hold down the rear gate opener button hook,

and remove the rear gate opener button.

B: INSTALLATION

CAUTION:

Make sure that the harness grommet is secure-

ly installed.

If not properly installed, this may cause leaks.

Install each part in the reverse order of removal.

C: INSPECTION

1) Disconnect the rear gate opener button harness

connector.

2) Check the resistance between rear gate opener

button connector terminals.

3) Replace the rear gate opener button if the in-

spection result is not within the standard value.

Switch

Terminal No.

Standard

Open

1 and 2

Less than 1 Ω

Close

1 MΩ or more

SL-00742