Subaru Impreza 3 / Impreza WRX / Impreza WRX STI. Manual — part 14

PI-10

Pre-delivery Inspection

PRE-DELIVERY INSPECTION

• Passenger’s side

Alarm sound operational check

• The system uses the buzzer and sounds the

alarm when the door is locked or unlocked. The

alarm sound can be turned OFF. To turn the alarm

sound from ON to OFF, close all doors, (with the

key not inserted in the key cylinder), hold down the

“UNLOCK” side of the power door lock switch and

insert the key in the key cylinder. Within 10 sec-

onds, insert and take out the key for 5 times or

more, and within 10 seconds after that, open and

close the driver’s door. With the door closed, the

hazard light will flash 3 times, indicating that the

alarm sound has been turned OFF. To turn the

alarm sound from OFF to ON, perform this proce-

dure again. The hazard light will flash 3 times, indi-

cating that the alarm has been turned ON.

21.SECURITY SYSTEM

Check that the security system operates as indicat-

ed below.

1) Fully open all the door windows.

2) Remove the key from the ignition switch and

close all the doors including rear gate.

3) Press the “LOCK/ARM” button on the keyless

transmitter once.

4) If all doors lock, and the security display light

flashes as indicated below, the alarm system is in

the monitoring prepared condition.

• Alarm system monitoring prepared condition

5) Check that the system enters monitoring condi-

tion 30 seconds after the condition in 4).

• Alarm system monitoring condition (all models)

PI-00722

PI-00357

(A) Light ON
(B) Light OFF

(C) 2 seconds

(A) Light ON
(B) Light OFF

(C) 2 seconds

PI-00504

PI-00315

(A)

(B)

(C)

(A)

(B)

(C)

PI-00265

PI-11

Pre-delivery Inspection

PRE-DELIVERY INSPECTION

6) Press the “UNLOCK/DISARM” button on the

keyless transmitter once.

7) If the driver’s door is unlocked, and the security

display light flashes as indicated below, the alarm

system is in the non-monitoring condition.

• Alarm system non-monitoring condition

8) Press the “LOCK/ARM” button once on the key-

less transmitter with one of the doors (including the

rear gate) opened.

9) Check that the buzzer sounds 5 times to give the

door not fully closed warning.

10) Close all the doors including rear gate.

11) Check that the alarm system is in the monitor-

ing prepared condition (all the doors lock).

• Alarm system monitoring prepared condition

12) Check that the system enters monitoring condi-

tion 30 seconds after the condition in 11).

13) Press the “UNLOCK/DISARM” button on the

keyless transmitter once and turn into non-monitor-

ing condition.

(A) Light ON
(B) Light OFF

(C) 3 seconds

PI-00358

PI-00504

(A)

(B)

(C)

PI-00266

PI-00357

(A) Light ON
(B) Light OFF

(C) 2 seconds

(A) Light ON
(B) Light OFF

(C) 2 seconds

PI-00315

(A)

(B)

(C)

(A)

(B)

(C)

PI-00265

PI-00358

PI-12

Pre-delivery Inspection

PRE-DELIVERY INSPECTION

14) With one of all the doors open (including the

rear gate), press the “LOCK” side of the power door

lock switch.

• Driver’s side

• Passenger’s side

15) Close all the doors including rear gate.

16) All the doors are locked and the alarm system

is in the monitoring prepared condition.

• Alarm system monitoring prepared condition

17) Check that the system enters monitoring condi-

tion 30 seconds after the condition in 16).

18) When the alarm system is in the monitoring

condition, use the inner lock knob or the key to un-

lock the door, and open the door.

19) Check that the alarm condition occurs (horn

sounds continuously, hazard light flashes, security

indicator illuminates).

20) Check that the condition in 19) continues for 30

seconds or more, or until the “UNLOCK/DISARM”

button of the keyless transmitter is pressed, or until

the ignition switch is turned ON with the correct ig-

nition key.

21) On models equipped with an impact sensor, hit

the windshield glass with your hand with the alarm

system in the monitoring condition, to check that

the alarm condition occurs.

22) When none of above is applicable, perform

troubleshooting for the security system. <Ref. to

SL-26, INSPECTION, Security System.>

22.SEAT

1) Check that each seat provides full functionality in

sliding and reclining. Check all available functions

of the rear seat such as a trunk-through center arm-

rest.

2) Check the passenger’s seat occupant detection

system.

(1) Empty the passenger’s seat and turn the ig-

nition switch to ON.

(A) Light ON
(B) Light OFF

(C) 2 seconds

PI-00720

PI-00722

PI-00315

(A)

(B)

(C)

(A) Light ON
(B) Light OFF

(C) 2 seconds

(A)

(B)

(C)

PI-00265

PI-13

Pre-delivery Inspection

PRE-DELIVERY INSPECTION

(2) Check that the passenger airbag ON/OFF

indicator lights both turn on simultaneously for

approximately six seconds, and after turning off

for two seconds, only the OFF light illuminates.

3) With a person weighing approximately 70 kg

(155 lb) or more sitting in the passenger’s seat,

check whether the ON light of the passenger’s air-

bag ON/OFF indicator illuminates or not.

4) Have the passenger get out of the passenger’s

seat, and check whether the OFF light of the pas-

senger side airbag ON/OFF indicator illuminates.

23.SEAT BELT

1) Pull out the seat belt and then release it. Check

that the belt retracts smoothly.

2) Check seat warning system

(1) Turn the ignition switch to ON without driv-

er’s and passenger’s seat belts on.

(2) Check the seat belt warning lights of the

driver’s and the passenger’s blink for approxi-

mately six seconds and the buzzer sounds in-

termittently.

(3) Then check that the seat belt warning lights

illuminate and blink in a cycle of approximately

15 seconds. (If no one is seated on the passen-

ger’s seat, the seat belt warning light of the pas-

senger’s will not operate.)

24.TPMS (U.S. MODELS ONLY)

1) Turn the ignition switch to ON, and check that

the TPMS warning light is in a normal operation

condition.

• Normal operation (IG ON (Light check))

2) If the TPMS warning light display does not oper-

ate normally, check and repair the system. <Ref. to

TPM(diag)-2, Basic Diagnostic Procedure.>

25.ECM PROTECTOR

For Canada model, check the ECM protector instal-

lation conditions. Make sure that the special nut

and the plastic cover of ECM protector are securely

installed.

(A) Airbag ON/OFF indicator light (U.S. model)
(B) Airbag ON/OFF indicator light (Canada, Mexico

model)

(B)

(B)

(B)

(A)

PI-00450

(A) ECM protector
(B) Special nut

(C) Plastic cover

2s

IGN ON

ON

OFF

PI-00376

(B)

(B)

(C)

(A)

PI-00453