Subaru Impreza (2022 year). Manual in english — page 27
(433,1)
Replacing bulbs
WARNING
Bulbs may become very hot while
illuminated. Before replacing bulbs,
turn off the lights and wait until the
bulbs cool down. Otherwise, there is
a risk of sustaining a burn injury.
CAUTION
Replace any bulb only with a new
bulb of the specified wattage. Using
a bulb of different wattage could
result in a fire. For the specified
wattage of each bulb, refer to “Bulb
chart”
NOTE
For models with type B combination
meter, if SRH is malfunctioning, the
SRH OFF indicator light appears on the
combination meter when the ignition
switch is in the “ON” position. It
indicates that SRH has been deacti-
vated. Contact a SUBARU dealer for an
inspection.
&
Headlights (models with LED
headlights)
LED headlight warning light (type B)
The LED headlight warning light illumi-
nates if the LED headlights malfunction.
Have your vehicle inspected at a SUBARU
dealer as soon as possible.
&
Headlights (models with ha-
logen headlights)
CAUTION
Halogen headlight bulbs become
very hot while in use. If you touch
the bulb surface with bare hands or
greasy gloves, fingerprints or
grease on the bulb surface will
develop into hot spots, causing the
bulb to break. If there are finger
prints or grease on the bulb surface,
wipe them away with a soft cloth
moistened with alcohol.
NOTE
.
If headlight aiming is required, con-
sult your SUBARU dealer for proper
adjustment of the headlight aim.
.
It may be difficult to replace the
bulbs. Have the bulbs replaced by your
SUBARU dealer if necessary.
Perform the following steps to replace the
bulbs.
Right-hand side
1. Use a screwdriver to undo the clips on
the air intake duct, then remove the air
intake duct.
– CONTINUED –
Maintenance and service/Replacing bulbs
11-39
11
(434,1)
Left-hand side
2. Use a screwdriver to remove the
secured clip of the washer tank. To make
it easy to access the bulb, turn the neck of
the washer fluid filler pipe as illustrated.
1)
Low beam bulb
2)
High beam bulb
3. Disconnect the electrical connector
from the bulb and remove the bulb from
the headlight assembly by turning it
counterclockwise.
4. Replace the bulb with new one. At this
time, use care not to touch the bulb
surface.
5. To install the bulb to the headlight
assembly, turn it clockwise until it clicks.
6. Reconnect the electrical connector.
7. Install the air intake duct with clips
(right-hand side).
8. Set the washer fluid filler pipe to the
original place and secure it by clip (left-
hand side).
&
Front turn signal light
It may be difficult to replace the bulbs.
Have the bulbs replaced by your SUBARU
dealer if necessary.
&
Parking light
It may be difficult to replace the bulbs.
Have the bulbs replaced by your SUBARU
dealer if necessary.
&
Front fog light (if equipped)
It may be difficult to replace the bulbs.
Have the bulbs replaced by your SUBARU
dealer if necessary.
&
Rear combination lights
!
Sedan
Maintenance and service/Replacing bulbs
11-40
(435,1)
1. Remove the clips from the trunk trim
with a flat-head screwdriver.
2. Open the rear portion of the trunk trim
panel as illustrated.
NOTE
Make sure that the “
*
” part of the trunk
trim in the illustration does not contact
the trunk lid stay. If the “
*
” part is bent,
the trunk trim may be torn.
1)
Tail and rear side marker light
2)
Rear turn signal light
3. Remove the bulb socket from the rear
combination light assembly by turning it
counterclockwise.
4. Pull the bulb out of the bulb socket and
replace it with a new one.
5. Set the bulb socket into the rear
combination light assembly and turn it
clockwise until it locks.
6. Secure the rear trunk trim panel with
the clips.
!
5-door models
1. Remove the covers.
2. Using a Phillips screwdriver, remove
the upper and lower screws that secure the
rear combination light assembly.
– CONTINUED –
Maintenance and service/Replacing bulbs
11-41
11
(436,1)
3. Slide the rear combination light as-
sembly rearward and remove it from the
vehicle.
1)
Tail light
2)
Rear side marker light
3)
Rear turn signal light
4. Remove the bulb socket from the rear
combination light assembly by turning it
counterclockwise.
5. Pull the bulb out of the bulb socket and
replace it with a new one.
6. Set the bulb socket into the rear
combination light assembly and turn it
clockwise until it locks.
1)
Guide pins
2)
Catches
3)
Clips
7. Put the rear combination light assem-
bly into place while aligning the 2 guide
pins and catches with the guide holes and
clips on the vehicle.
8. Tighten the upper and lower screws.
9. Reinstall the covers.
&
Backup light
!
Sedan
NOTE
It may be difficult to replace the bulbs.
We recommend that you have the bulbs
replaced by your SUBARU dealer if
necessary.
Maintenance and service/Replacing bulbs
11-42
(437,1)
1. Open the trunk.
2. Remove the trunk trim lining by remov-
ing the clips indicated in the illustration.
1)
Left side light
2)
Right side light
3. For left side light, turn the bulb socket
clockwise and remove it.
For right side light, turn the bulb socket
counterclockwise and remove it.
4. Pull the bulb out of the bulb socket and
replace it with a new one.
5. For left side light, turn the bulb socket
counterclockwise and install it.
For right side light, turn the bulb socket
clockwise and install it.
6. Reinstall the trunk trim lining.
!
5-door models
1. Apply a flat-head screwdriver to the
light cover as shown in the illustration, and
pry the light cover off from the rear gate
trim.
1)
Right side light
2)
Left side light
2. For left side light, turn the bulb socket
clockwise and remove it.
For right side light, turn the bulb socket
counterclockwise and remove it.
– CONTINUED –
Maintenance and service/Replacing bulbs
11-43
11
(438,1)
3. Pull the bulb out of the bulb socket and
replace it with a new one.
4. For left side light, turn the bulb socket
counterclockwise and install it.
For right side light, turn the bulb socket
clockwise and install it.
5. Install the light cover on the rear gate.
&
License plate light
!
Sedan
1. Open the trunk and remove the clips
from the trunk lid trim with a flat-head
screwdriver.
2. Turn the bulb socket counterclockwise
and pull out the socket.
3. Pull the bulb out of the socket.
4. Install a new bulb.
5. Reinstall the bulb socket and the trunk
lid trim.
!
5-door models
1. The license plate lights must be
pushed outwards, and then pulled out to
be removed.
Maintenance and service/Replacing bulbs
11-44
(439,1)
2. Turn the bulb socket counterclockwise
and pull out the socket.
3. Pull the bulb out of the socket.
4. Install a new bulb.
5. Reinstall the bulb socket and the
license plate light cover.
&
Map light
CAUTION
Replacing the bulb could cause
burns since the bulb may be very
hot. Have the bulb replaced by your
SUBARU dealer.
&
Vanity mirror light (if
equipped)
CAUTION
Replacing the bulb could cause
burns since the bulb may be very
hot. Have the bulb replaced by your
SUBARU dealer.
&
Dome light (all models) and
cargo area light (5-door mod-
els)
Dome light
Cargo area light
1. Remove the lens by prying the edge of
the lens with a flat-head screwdriver.
2. Pull the bulb out of the socket.
3. Install a new bulb.
4. Reinstall the lens.
&
Trunk light (sedan)
CAUTION
Replacing the bulb could cause
burns since the bulb may be very
hot. Have the bulb replaced by your
SUBARU dealer.
– CONTINUED –
Maintenance and service/Replacing bulbs
11-45
11
(440,1)
&
Other bulbs
It may be difficult to replace the bulbs.
Have the bulbs replaced by your
SUBARU dealer if necessary.
&
Adjusting headlight aim
(models with LED headlights)
1)
Adjustment bolt A
2)
Adjustment bolt B
!
Before checking the headlight aim-
ing
1. Make sure the vehicle has a full tank of
gasoline and the area around the headlight
is not deformed.
2. Park the vehicle on level ground.
3. Sit in the driver’s seat.
4. Bounce the vehicle several times.
!
Headlight aim adjustment
Right-hand side
1. Use a screwdriver to undo the clips on
the air intake duct, and then remove the air
intake duct (right-hand side).
1)
Adjustment direction mark
2. Turn bolt A clockwise or counterclock-
wise to adjust it.
Remember the direction of the rotation and
number of rotations.
3. Turn bolt B the same number of turns
and in the same direction as step 2.
NOTE
.
If the headlight aim cannot be ad-
justed, contact your SUBARU dealer.
.
To inspect the headlight aim posi-
tion, consult a SUBARU dealer.
Maintenance and service/Replacing bulbs
11-46
(441,1)
Replacing key battery
The access key fob/transmitter battery
may be discharged under the following
conditions.
.
The operation of the keyless access
function is unstable.
.
The operating distance of the remote
keyless entry system is unstable.
.
The transmitter does not operate prop-
erly when used within the standard dis-
tance.
Replace the battery with a new one.
&
Safety precautions
CAUTION
.
Do not let dust, oil or water get on
or in the access key fob/transmit-
ter when replacing battery.
.
Before replacing the battery, re-
move any static electricity.
.
Be careful not to touch or damage
the printed circuit board in the
access key fob/transmitter when
replacing the battery.
.
Be careful not to allow children to
touch the battery and any re-
moved parts; children could
swallow them.
.
There is a danger of an explosion
if the battery is incorrectly re-
placed. Replace only with the
same or equivalent type of the
battery.
.
Batteries should not be exposed
to excessive heat such as bright
sunlight, fire or the like.
NOTE
.
Replace only with the same or
equivalent type of battery recom-
mended by the manufacturer.
.
Dispose of used batteries according
to local laws.
.
Mount the battery in the correct
orientation to prevent fluid leakage.
Be careful not to bend the terminals. It
may result in a malfunction.
.
It is recommended that the battery
be replaced by a SUBARU dealer.
.
Use a new battery.
.
After replacing the battery, confirm
that the transmitter functions properly.
&
Replacing battery of access
key fob
CAUTION
When removing or reinstalling the
access key fob cover, make sure that
the plastic part does not come off or
become misaligned.
Battery: Button battery CR2032 or
equivalent
1)
Release button
2)
Emergency key
1. Take out the emergency key.
– CONTINUED –
Maintenance and service/Replacing key battery
11-47
11
(442,1)
2. Wrap a flat-head screwdriver with vinyl
tape or a cloth, and insert it in the gap to
remove the cover.
3. Take out the battery using a flat-head
screwdriver with vinyl tape or a cloth.
4. Insert a new battery with its positive (+)
side facing upward as shown in the figure.
5. Attach the cover to the access key fob
by fitting the projections and recesses
together.
&
Replacing transmitter battery
Battery: Button battery CR1620 or
equivalent
1. Wrap a flat-head screwdriver with vinyl
tape or a cloth. Open the key head using a
flat-head screwdriver.
Maintenance and service/Replacing key battery
11-48
(443,1)
2. Remove the transmitter case from the
key head.
3. Open the transmitter case by releasing
the hooks.
1)
Negative (−) side facing up
4. Replace the old battery with a new
battery making sure to install the new
battery with the negative (−) side facing up.
5. Put together the transmitter case by
fitting the hooks on the case.
6. Reinstall the transmitter case in the
key head.
7. Refit the removed half of the key head.
Maintenance and service/Replacing key battery
11-49
11
(445,1)
Specifications. . . . . . . . . . . . . . 12-2
Dimensions. . . . . . . . . . . . . . ... 12-2
Engine . . . . . . . . . . . . . . . . .. 12-3
Fuel . . . . . . . . . . . . . . . . . .. 12-3
Engine oil . . . . . . . . . . . . . . . . 12-4
Manual transmission, front differential and rear
differential gear oil . . . . . . . . . . . .. 12-6
Fluids . . . . . . . . . . . . . . . . ... 12-7
Engine coolant. . . . . . . . . . . . . .. 12-7
Electrical system . . . . . . . . . . . . .. 12-7
Tires. . . . . . . . . . . . . . . . . . 12-8
Temporary spare tires . . . . . . . . . . ... 12-8
Brake disc . . . . . . . . . . . . . . . 12-8
Bulb chart. . . . . . . . . . . . . . . .. 12-9
Safety precautions. . . . . . . . . . . . 12-9
Bulb chart . . . . . . . . . . . . . . .. 12-10
Vehicle identification . . . . . . . . . . .. 12-13
Specifications
12
(446,1)
Specifications
These specifications are subject to change without notice.
&
Dimensions
in (mm)
Item
5-door models
Sedan
Overall length
176.2 (4,475)
182.7 (4,640)
Overall width
70.0 (1,775)
Overall height
Models with roof rails
58.9 (1,495)
57.3 (1,455)
Models without roof rails
58.3 (1,480)*
1
57.3 (1,455)*
2
Wheel base
105.1 (2,670)
Tread
Front
60.6 (1,540)
Rear
60.8 (1,545)
Ground clearance*
3
5.1 (130)
*1: Models with shark fin type roof antenna
*2: Models with monopole roof antenna
*3: Measured with vehicle empty
Specifications/Specifications
12-2
(447,1)
&
Engine
Engine model
FB20 (2.0 L, DOHC)
Engine type
Horizontally opposed, liquid cooled 4 cylinder, 4-stroke direct injection gasoline engine
Displacement cu-in (cc)
122 (1,995)
Bore
6
Stroke in (mm)
3.31
6
3.54 (84.0
6
90.0)
Compression ratio
12.5 : 1
Firing order
1 – 3 – 2 – 4
&
Fuel
Fuel requirement
Fuel tank capacity
Unleaded gasoline with 87 AKI (90 RON) or higher
13.2 US gal (50 liters, 11.0 Imp gal)
For more details, refer to “Fuel”
– CONTINUED –
Specifications/Specifications
12-3
12
(448,1)
&
Engine oil
For the checking, adding and replacing procedure or other details, refer to “Engine oil”
NOTE
The procedure for changing the engine oil and oil filter should be performed by a properly-trained expert. It is recommended
that you have this service performed by your SUBARU dealer.
!
Approved engine oil
Always use the SUBARU approved engine oil. For further details, please contact your SUBARU dealer. If the approved engine oil is
unavailable, use the alternative engine oil described on the next page.
Specifications/Specifications
12-4
(449,1)
!
Alternative engine oil
If the SUBARU approved oil is unavailable, the following alternative oil can be used.
NOTE
Each quantity indicated here is only a guideline. The necessary quantity for replacement may differ slightly depending on the
temperature and other factors.
Oil grade
SAE viscosity No. and
applicable temperature
Engine oil capacity
API (American Petroleum Insti-
tute) classification
SN
with the
words “RESOURCE CONSER-
VING”,
SN PLUS
with the words
“RESOURCE CONSERVING” or
SP
with the words “RESOURCE
CONSERVING”
or
ILSAC (International Lubricant
Specification Advisory Commit-
tee)
GF-5
or
GF-6A
, which can
be identified with the ILSAC
certification mark (Starburst
mark)
0W-20 synthetic
oil is the required oil
for optimum engine performance and
protection. Conventional oil may be
used if synthetic oil is unavailable.
*: If 0W-20 synthetic oil is not available,
5W-30 conventional oil may be used
if replenishment is needed but should
be changed to 0W-20 synthetic oil at
the next oil change.
– Adding the oil from low level to
full level:
1.1 US qt (1.0 liter, 0.9 Imp qt)
– Changing the oil and oil filter:
4.7 US qt (4.4 liters, 3.9 Imp qt)
– CONTINUED –
Specifications/Specifications
12-5
12
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст