Subaru Impreza (2022 year). Manual in english — page 11
(171,1)
&
Power steering warning
light
While the engine is running, this warning
light illuminates when a malfunction has
been detected in the electric power steer-
ing system.
CAUTION
When the power steering warning
light is illuminated, there may be
more resistance when the steering
wheel is operated. Drive carefully to
the nearest SUBARU dealer and
have the vehicle inspected immedi-
ately.
NOTE
If the steering wheel is operated in the
following ways, the power steering
control system may temporarily limit
the power assist in order to prevent the
system components, such as the con-
trol computer and drive motor, from
overheating.
.
The steering wheel is operated fre-
quently and turned sharply while the
vehicle is maneuvered at extremely low
speeds, such as while frequently turn-
ing the steering wheel during parallel
parking.
.
The steering wheel remains in the
fully turned position for a long period of
time.
At this time, there will be more resis-
tance when steering. However this is
not a malfunction. Normal steering
force will be restored after the steering
wheel is not operated for a while and
the power steering control system has
an opportunity to cool down. However,
if the power steering is operated in a
non-standard way which causes power
assist limitation to occur too frequently,
that may result in a malfunction of the
power steering control system.
&
Vehicle Dynamics Con-
trol warning light/Vehi-
cle Dynamics Control
operation indicator
light
!
Vehicle Dynamics Control warning
light
CAUTION
The Vehicle Dynamics Control sys-
tem provides its ABS control
through the electrical circuit of the
ABS. Accordingly, if the ABS is
inoperative, the Vehicle Dynamics
Control system becomes unable to
provide ABS control. As a result, the
Vehicle Dynamics Control system
also becomes inoperative, causing
the warning light to illuminate.
Although both the Vehicle Dynamics
Control system and ABS are inop-
erative in this case, the ordinary
functions of the brake system are
still available. You will be safe while
driving with this condition, but drive
carefully and have your vehicle
checked at a SUBARU dealer as
soon as possible.
NOTE
.
If the electrical circuit of the Vehicle
Dynamics Control system itself mal-
functions, the warning light only illumi-
nates. At this time, the ABS (Anti-lock
Brake System) remains fully opera-
tional.
.
The warning light illuminates when
the electronic control system of the
ABS/Vehicle Dynamics Control system
malfunctions.
The Vehicle Dynamics Control system is
probably inoperative under any of the
following conditions. Have your vehicle
checked at a SUBARU dealer immedi-
– CONTINUED –
Instruments and controls/Warning and indicator
3-23
3
(172,1)
ately.
.
The warning light does not illuminate
when the ignition switch is turned to the
“ON” position.
.
The warning light illuminates while the
vehicle is running.
NOTE
If the warning light behavior is as
described in the following examples,
the Vehicle Dynamics Control system
may be considered normal.
.
The warning light illuminates when
the ignition switch is turned to the “ON”
position and turns off approximately 2
seconds after the engine has started.
.
The warning light illuminates right
after the engine is started but turns off
immediately, remaining off.
.
The warning light illuminates after
the engine has started and turns off
while the vehicle is subsequently being
driven.
.
The warning light illuminates during
driving, but it turns off immediately and
remains off.
.
The warning light illuminates when
the engine has stalled and continues to
illuminate after the engine has been
restarted. However, it will turn off once
the vehicle starts moving.
!
Vehicle Dynamics Control operation
indicator light
The indicator light flashes during activation
of the skid suppression function and during
activation of the traction control function.
NOTE
.
The light may remain illuminated for
a short period of time after the engine
has been started, especially in cold
weather. This does not indicate the
existence of a problem. The light
should turn off as soon as the engine
has warmed up.
.
The indicator light illuminates when
the engine has developed a problem
and the CHECK ENGINE warning light/
malfunction indicator light is on.
The Vehicle Dynamics Control system is
probably malfunctioning under the follow-
ing condition. Have your vehicle checked
at a SUBARU dealer as soon as possible.
.
The light does not turn off even after the
lapse of several minutes (the engine has
warmed up) after the engine has started.
&
Vehicle Dynamics Con-
trol OFF indicator light
The light illuminates when the Vehicle
Dynamics Control OFF switch is pressed
to deactivate the Vehicle Dynamics Con-
trol system.
The Vehicle Dynamics Control system is
probably malfunctioning under any of the
following conditions. Have your vehicle
checked at a SUBARU dealer immedi-
ately.
.
The light does not illuminate when the
ignition switch is turned to the “ON”
position.
.
The light does not turn off even once
several seconds have elapsed after the
ignition switch has been turned to the “ON”
position.
Instruments and controls/Warning and indicator
3-24
(173,1)
&
Warning chimes and
warning indicator of the
keyless access with
push-button start sys-
tem (if equipped)
Access key warning indicator
The warning chime and the access key
warning light serve the following purposes:
.
To minimize improper operation of the
keyless access with push-button start
system
.
To protect your vehicle from theft
When the warning chime sounds and/or
the warning indicator flashes, take the
appropriate action.
WARNING
Never drive the vehicle if the indica-
tor on the push-button ignition
switch is flashing in green when
starting the engine. This indicates
the status that the steering wheel is
not released and could result in an
accident involving serious injury or
death.
CAUTION
.
When starting the engine again
after the operation indicator on
the push-button ignition switch
flashes in green, if the operation
indicator is still flashing in green,
there could be a steering lock
m a l f u n c t i o n . C o n t a c t y o u r
SUBARU dealer as soon as pos-
sible.
.
When the operation indicator on
the push-button ignition switch
flashes in orange, contact a
SUBARU dealer immediately.
NOTE
.
When doors are not locked because
the access key fob is left inside the
trunk, you cannot open the trunk lid by
pushing the trunk opener button on the
trunk lid. Pull the trunk lid release lever
upward to open the trunk lid. Refer to
“To open the trunk lid from inside”
.
Do not leave the access key fob
inside the trunk. Depending on the
status of the access key fob and
situation, the trunk lockout protect
function may not operate. Make sure
that you carry the access key fob, and
close the trunk lid.
.
Even when the access key fob is
within the operating ranges inside the
vehicle, the access key warning for
engine start may be provided depend-
ing on the status of the access key fob
and the environmental conditions.
.
When the access key fob is taken out
of the vehicle through an open window,
the access key fob takeout warning or
passenger access key fob takeout
warning will not be provided.
!
List of warnings
CAUTION
When any of the following warnings
occurs even if the access key warn-
ing indicator does not appear, take
the appropriate action.
– CONTINUED –
Instruments and controls/Warning and indicator
3-25
3
(174,1)
Inside warning
chime
Outside warning
chime
Operation indicator
on push-button igni-
tion switch
Status
Action
Ding, ding ...
(intermittent)
—
—
The driver’s door was opened while the
push-button ignition switch is “ACC” (in
CVT models, when the select lever is in
the “P” position).
Switch the push-button ignition switch to
“OFF”, or close the driver’s door.
When exiting the vehicle, be sure to
switch the push-button ignition switch to
“OFF”.
The push-button ignition switch was
switched to “OFF” while the driver’s door
is open.
Close the driver’s door.
Ding
Short beep
(2 seconds)
—
Lockout warning:
An attempt was made to lock all doors
while the access key fob is left inside the
vehicle.
Take out the access key fob from the
vehicle, and lock the doors.
The doors cannot be locked while the
access key fob is inside the vehicle.
A chirp sound will be heard, and all doors
will be unlocked.
—
Short beep
(2 seconds)
—
Trunk lockout warning:
The trunk was closed with the access key
fob in it while all doors are locked (or
during the automatic lock time period)
(sedan).
Take out the access key fob from the
trunk, and close the trunk.
By pressing the trunk opener button after
this warning chime sounds, the trunk can
be unlocked.
Access key fob lock-in warning:
The door lock sensor was touched while
the push-button ignition switch is “OFF”
and the access key fob is inside the
vehicle.
Take out the access key fob from the
vehicle, and lock the doors.
If the access key fob is inside the vehicle,
the doors cannot be locked.
—
Beep, beep, beep,
beep, beep
(5 times)
—
Door ajar warning:
The door lock sensor is touched while the
ignition switch is in the “OFF” position and
one of the doors including the rear gate is
opened.
Close the doors securely and lock them.
If one of the doors including the rear gate
is opened, the doors cannot be locked.
Instruments and controls/Warning and indicator
3-26
(175,1)
Inside warning
chime
Outside warning
chime
Operation indicator
on push-button igni-
tion switch
Status
Action
Ding
Long beep
(60 seconds max.)
—
Power warning:
The door lock sensor was touched while
carrying the access key fob, the push-
button ignition switch is in a position other
than “OFF” (in CVT models, when the
select lever is in the “P” position).
Return the access key fob inside the
vehicle, or switch the push-button ignition
switch to “OFF”.
If the push-button ignition switch is not
switched to “OFF”, the doors cannot be
locked.
Ding, ding ...
(7 seconds)
—
—
Access key warning:
The vehicle was driven while the access
key fob is not inside the vehicle.
Carry the access key fob, and drive the
vehicle.
Ding
—
—
Access key warning for engine start:
The push-button ignition switch was
pressed while the access key fob is not
inside the vehicle.
Carry the access key fob, and press the
push-button ignition switch.
Ding
Beep, beep, beep
(3 times)
—
Access key takeout warning:
The driver exited the vehicle with the
access key fob and closed the driver’s
door while the push-button ignition switch
is in a position other than “OFF” (in CVT
models, when the select lever is in the “P”
position).
Switch the push-button ignition switch to
“OFF”, and get out of the vehicle.
Ding
Beep, beep, beep
(3 times)
—
Passenger access key takeout warn-
ing:
A fellow passenger exited the vehicle with
the access key fob and closed a door
other than the driver’s door while the
push-button ignition switch is in a position
other than “OFF”.
Return the access key fob to inside the
vehicle, or switch the push-button ignition
switch to “OFF”.
– CONTINUED –
Instruments and controls/Warning and indicator
3-27
3
(176,1)
Inside warning
chime
Outside warning
chime
Operation indicator
on push-button igni-
tion switch
Status
Action
Long beep
(continuous)
Long beep
(continuous)
—
Access key takeout without P position
warning (CVT models):
The driver exited the vehicle with the
access key fob and closed the driver’s
door while the push-button ignition switch
is in a position other than “OFF” and the
select lever is in a position other than the
“P” position.
Shift the select lever to the “P” position,
switch the push-button ignition switch to
“OFF” and exit the vehicle.
Long beep
(continuous)
—
—
Select lever position warning (CVT
models):
The engine is turned off by pressing the
push-button ignition switch and the select
lever is in a position other than the “P”
position.
Start the engine, shift the select lever to
the “P” position, switch the push-button
ignition switch to “OFF” and exit the
vehicle.
Long beep
(continuous)
—
—
Select lever position warning (CVT
models):
The driver’s door was opened while the
push-button ignition switch is in a position
other than “OFF” and the select lever is in
a position other than the “P” position.
Shift the select lever to the “P” position,
switch the push-button ignition switch to
“OFF” and exit the vehicle.
Ding
—
—
The battery of the access key fob is low.
Replace the battery of the access key fob.
Ding
—
Flashes in green
(15 seconds max.)
Steering lock warning:
The engine start procedure was per-
formed, but the steering is still locked.
While turning the steering wheel right and
left lightly, depress the brake pedal and
press the push-button ignition switch.
Ding
—
Flashes in orange
(15 seconds max.)
System malfunction warning:
A malfunction was detected in the power
system or steering lock.
Contact a SUBARU dealer immediately
and have the vehicle inspected.
Instruments and controls/Warning and indicator
3-28
(177,1)
&
Security indicator light
This indicator light shows the status of the
alarm system. It also indicates operation of
the immobilizer system.
!
Alarm system
It blinks to show the driver the operational
status of the alarm system. For detailed
information, refer to “Alarm system”
!
Immobilizer system
The security indicator light starts blinking
in the following conditions.
For models with “keyless access with
push-button start system”:
.
Immediately after the push-button igni-
tion switch is turned to the “OFF” position.
.
Immediately after the driver’s door is
opened or closed when all of the following
conditions are met.
– The push-button ignition switch is in
the “ON” or “ACC” position.
– The engine is not running.
In the event that an unauthorized key is
used (for example, the key is unregistered
or the ID code does not match), the power
is not switched to “ON” and the security
indicator light continues blinking.
For models without “keyless access
with push-button start system”:
.
Approximately 60 seconds after the
ignition switch is turned from the “ON”
position to the “ACC” or “LOCK” position.
.
Immediately after the key is pulled out.
If the indicator light does not blink in the
above conditions, it may indicate that
immobilizer system may be malfunction-
ing. Contact your nearest SUBARU dealer
immediately.
In the event that an unauthorized key (for
example, an unauthorized duplicate) is
used to start the engine, the security
indicator light illuminates. For details about
the immobilizer system, refer to “Immobi-
lizer”
NOTE
.
The security indicator light remains
off in the following conditions. It means
that the matching of the ID code is
completed and the immobilizer system
is deactivated, and it does not indicate
a malfunction.
Models with “keyless access with
push-button start system”:
– The engine is running.
– The push-button ignition switch
has been turned to the “ON” or
“ACC” position and the driver’s
door has not been opened or
closed.
Models without “keyless access
with push-button start system”:
– The engine is running.
– For approximately 60 seconds
after the ignition switch is turned
from the “ON” position to the “ACC”
or “LOCK” position.
– The ignition switch is in the “ON”
position.
.
Even if a malfunction occurs, such
as the security indicator light flashes
irregularly, it will not affect the func-
tionality of the immobilizer system.
– CONTINUED –
Instruments and controls/Warning and indicator
3-29
3
(178,1)
&
SI-DRIVE indicator light (if
equipped)
1)
Intelligent (I) mode indicator
2)
Sport (S) mode indicator
This light indicates the current SI-DRIVE
mode.
For details of SI-DRIVE mode, refer to
“SI-DRIVE”
&
Select lever/gear position in-
dicator (CVT models)
1)
Upshift indicator
2)
Downshift indicator
3)
Select lever/gear position indicator
This indicator shows the position of the
select lever.
For models with manual mode, when the
manual mode is selected, the gear position
indicator (which shows the current gear
selection) and the upshift/downshift indi-
cator light up. Refer to “Continuously
variable transmission”
&
Turn signal indicator
lights
These lights show the operation of the turn
signal or lane change signal.
If the indicator lights do not blink or blink
rapidly, the turn signal bulb may be burned
out. Replace the bulb as soon as possible.
Refer to “Replacing bulbs”
&
High beam indicator
light
This light shows that the headlights are in
the high beam mode.
This indicator light also illuminates when
the headlight flasher is operated.
&
High beam assist indi-
cator light (if equipped)
This light illuminates when the high beam
assist function is activated. For details
about the high beam assist function, refer
to “High beam assist function”
Instruments and controls/Warning and indicator
3-30
(179,1)
&
Cruise control indicator
light (if equipped)
This light illuminates when the cruise
control main button is pressed to activate
the cruise control function. For details,
refer to “To set cruise control”
If this light blinks, do not use the cruise
control. In addition, if it blinks frequently,
contact your SUBARU dealer for an
inspection.
CAUTION
If the CHECK ENGINE warning light/
malfunction indicator light illumi-
nates, the cruise control indicator
light flashes at the same time. At this
time, avoid driving at high speed and
have your vehicle inspected at a
SUBARU dealer as soon as possi-
ble.
&
Cruise control set indi-
cator light (if equipped)
This light illuminates when vehicle speed
has been set to use the cruise control
function. Refer to “To set cruise control”
&
Automatic headlight
beam leveler warning
light (models with LED
headlights)
This light illuminates when the automatic
headlight beam leveler does not operate
normally.
If this light illuminates during driving, have
your vehicle inspected at your SUBARU
dealer.
&
LED headlight warning
light (models with LED
headlights)
This light illuminates if the LED headlights
malfunction. Have your vehicle inspected
at a SUBARU dealer as soon as possible.
&
Steering Responsive
Headlight warning light/
Steering Responsive
Headlight OFF indicator
light (if equipped)
This light illuminates when the Steering
Responsive Headlight OFF switch is
pressed to deactivate the Steering Re-
sponsive Headlight. Also, the light flashes
when a malfunction occurs in the Steering
Responsive Headlight. Refer to “Steering
Responsive Headlight (SRH)”
&
Front fog light indicator
light (if equipped)
This indicator light illuminates while the
front fog lights are illuminated.
&
Headlight indicator
light (if equipped)
This indicator light illuminates under the
following conditions.
.
The light switch is turned to the “
” or
“
” position.
.
The light control switch is in the “AUTO”
position and the headlights illuminate
automatically.
– CONTINUED –
Instruments and controls/Warning and indicator
3-31
3
(180,1)
&
BSD/RCTA warning in-
dicator (if equipped)
This warning indicator appears when the
BSD/RCTA is malfunctioning. In this case
the BSD/RCTA warning indicator will be
shown on the combination meter display
(color LCD). When this indicator appears,
have your vehicle inspected by your
SUBARU dealer as soon as possible.
&
BSD/RCTA OFF indica-
tor (if equipped)
The indicator appears when the BSD/
RCTA OFF switch is pressed to deactivate
the BSD/RCTA, or when the BSD/RCTA is
suspended temporarily. In this case the
BSD/RCTA OFF indicator will be shown on
the combination meter display (color
LCD). For details, refer to “BSD/RCTA”
&
RAB warning indica-
tor (if equipped)
This indicator illuminates if the Reverse
Automatic Braking (RAB) system malfunc-
tions. Refer to “Reverse Automatic Brak-
ing (RAB) system”
&
RAB OFF indicator (if
equipped)
This indicator illuminates when the Re-
verse Automatic Braking (RAB) system is
turned OFF, or when the Reverse Auto-
matic Braking (RAB) system is suspended
temporarily. Refer to “Reverse Automatic
Braking (RAB) system”
&
Icy road surface warn-
ing indicator (if
equipped)
When the outside temperature is 37
8
F
(3
8
C) or less, the icy road surface warning
indicator will illuminate to inform the driver
that the road surface may be frozen.
NOTE
.
The outside temperature indicator
shows the temperature in the area
around the sensor. However, the tem-
perature may not be indicated correctly
or the update may be delayed in the
following conditions.
– While parking or driving at low
speeds
– When the outside temperature
changes suddenly (example: when
going in and out of an underground
parking area or when passing
through a tunnel)
– When starting the engine after
being parked for a certain period of
time
.
Treat the icy road surface warning
indicator only as a guide. Be sure to
check the condition of the road surface
before driving.
.
Once the icy road surface warning
indicator appears, it will not disappear
unless the outside temperature has
increased to 41
8
F (5
8
C) or higher.
Instruments and controls/Warning and indicator
3-32
(181,1)
Combination meter display
(color LCD) (if equipped)
WARNING
Always pay adequate attention to
safe driving when operating the
combination meter display (color
LCD) while the vehicle is in motion.
When operation of the combination
meter display (color LCD) interferes
with your ability to concentrate on
driving, stop the vehicle before
performing operations on the
screen. Also, do not concentrate on
the display while driving. Doing so
may cause you to look away from the
road and could result in an accident.
Various information will be shown on the
combination meter display (color LCD).
Also, a warning message will appear on
the display if a malfunction is detected. In
addition, several settings for the displayed
content can be performed.
Combination meter display (color LCD)
1)
ECO gauge (Refer to “ECO gauge”
2)
Warning screen (Refer to “Warning
screen”
3-35.)/Basic screen (Refer to
3)
EyeSight screen
4)
Cruise control information display*
5)
Telltale screen (Refer to “Telltale screen”
6)
Select lever/gear position indicator (Re-
fer to “Select lever/gear position indicator
(CVT models)”
7)
SI-DRIVE indicator light (if equipped)
(Refer to “SI-DRIVE”
8)
Odometer (Refer to “Odometer”
Double trip meter (Refer to “Double trip
meter”
9)
Fuel gauge (Refer to “Fuel gauge”
A:
· Models without the EyeSight system
· Models with the EyeSight system:
when the EyeSight system is deacti-
vated.
B:
Models with the EyeSight system:
when the EyeSight system is activated.
*: For models with the EyeSight system, the
cruise control information display will not be
shown when the EyeSight system is deac-
tivated.
– CONTINUED –
Instruments and controls/Combination meter display (color LCD)
3-33
3
(182,1)
&
Basic operation
Control switch
1)
(Up)
2)
/SET (Enter)
3)
(Down)
By operating “
” or “
” of the control
switch, the screens and selection items
can be switched. When the “
/SET”
switch is pulled toward you, the item can
be selected and set.
If there are some useful messages, such
as vehicle information, warning informa-
tion, etc., they will interrupt the current
screen, and appear on the display accom-
panied by a beep. If such a screen is
displayed, take proper action according to
the message shown on the screen.
The warning screen will return to the
original screen after a few seconds. While
the “
” information reminder is shown on
the display, it may be possible to display
the warning screen again. To recall the
message marked with “
” on the display,
pull the “ /SET” switch on the steering
wheel toward you.
NOTE
When the multi-function display (color
LCD) is set to the setting screen, the
combination meter display (color LCD)
cannot be controlled pulling on the
“
”, “
” and “
/SET” on the control
switch.
&
Welcome screen (opening
animation) and Good-bye
screen (ending animation)
When the driver’s door is opened and
closed after unlocking the door, the wel-
come screen (opening animation) will
appear on the combination meter display
(color LCD) for approximately 20 seconds.
When the ignition switch is turned to the
“LOCK”/“OFF” position, the combination
meter display (color LCD) gradually turns
off with showing the Good-bye screen
(ending animation).
NOTE
.
The welcome screen and the good-
bye screen may differ in the actual
words and appearance.
.
Once the welcome screen appears, it
takes a certain period of time to display
it again.
.
If the ignition switch is operated
after unlocking the driver’s door, the
welcome screen will not appear even
when the driver’s door is opened and
closed.
.
The welcome screen will disappear
when you lock the driver’s door by
using the remote keyless entry system
(all models) or the keyless access
function (if equipped) while the wel-
come screen is displayed.
.
The welcome screen including the
multi-function display (color LCD) (if
equipped) and the audio/navigation
unit can be set to on or off. For details,
refer to “Welcome Screen”
Instruments and controls/Combination meter display (color LCD)
3-34
(183,1)
&
Warning screen
Example of warning
If there is a warning message or a
maintenance notification, it will appear on
this screen. Take the appropriate actions
based on the messages indicated.
&
Telltale screen
1)
Telltale screen
When the corresponding situation occurs,
the following telltales will be displayed on
the telltale screen.
NOTE
When there is warning information to
display, it will be displayed in five
warning indicators, starting on the left
in ascending order of severity. If there
are six or more warning information
displayed, pull the “
/SET” switch and
check the item.
Mark
Name
Page
Door open warning light
LED headlight warning
indicator (models with
LED headlights)
High beam assist indi-
cator light (if equipped)
Steering Responsive
Headlight warning light
(if equipped)
Engine low oil level
warning light
RAB warning indicator
(if equipped)
RAB OFF indicator (if
equipped)
BSD/RCTA warning in-
dicator (if equipped)
BSD/RCTA OFF indi-
cator (if equipped)
Automatic headlight
beam leveler warning
light (models with LED
headlights)
– CONTINUED –
Instruments and controls/Combination meter display (color LCD)
3-35
3
(184,1)
Mark
Name
Page
Windshield washer fluid
warning light
Icy road surface warn-
ing indicator (if
equipped)
&
Basic screens
By operating the “
” or “
” switch on the
steering wheel, you can change the screen
that is always displayed.
Average fuel consumption screen:
: Average fuel consumption
: Driving range on remaining fuel
This screen displays the average rate of
fuel consumption since the trip meter was
last reset.
NOTE
The driving range on remaining fuel is
only a guide. The indicated value may
differ from the actual driving range on
remaining fuel, so you must immedi-
ately fill the tank when the low fuel
warning light illuminates.
Current fuel consumption screen:
: Current fuel consumption
: Driving range on remaining fuel
This screen displays the rate of fuel
consumption at the present moment.
NOTE
The driving range on remaining fuel is
only a guide. The indicated value may
differ from the actual driving range on
remaining fuel, so you must immedi-
ately fill the tank when the low fuel
warning light illuminates.
Instruments and controls/Combination meter display (color LCD)
3-36
(185,1)
Driving information screen:
: Journey time
: Journey distance
This screen displays the journey time (the
time that has elapsed since the ignition
switch was turned to the “ON” position)
and journey distance (the distance that
has been driven since the ignition switch
was turned to the “ON” position).
Digital speed screen:
1)
Speed limit (if equipped)
2)
Vehicle speed
This screen displays the current vehicle
speed.
SI-DRIVE mode screen (if equipped):
This screen indicates the current
SI-DRIVE mode with its throttle angle.
TPMS screen (U.S.-spec. models):
This screen displays each tire pressure.
– CONTINUED –
Instruments and controls/Combination meter display (color LCD)
3-37
3
(186,1)
When a tire is deflated, the deflated tire
and the tire pressure will be displayed on
the screen in yellow.
NOTE
.
The tire pressure values are dis-
played several minutes after driving.
.
You can set the tire pressure units.
For details about setting the units, refer
to “Tire Pressure Units”
.
Once the tire pressure monitoring
system detects the low tire pressure,
the tire pressure values will display in
yellow until the system detects the
normal tire pressure.
.
Immediately adjust the tire pressure
when the warning light illuminates.
When the tire pressure monitoring
system detects the adjusted tire pres-
sure, the warning light will turn off and
the tire pressure values will turn to
white.
.
For information about the specified
value of the air pressure, refer to
“Tires”
Menu screen entering screen:
While this screen is selected, pull and hold
the “
/SET” switch to enter the menu
screen.
&
Menu screens
Pull and hold the “
/SET” switch to enter
the menu screens when all of the following
conditions are satisfied.
.
The menu screen entering screen is
selected.
.
The “
” information reminder is off.
NOTE
.
While driving, the setting items
available on the combination meter
display (color LCD) are limited.
.
For function settings and adjust-
ments on the combination meter dis-
play, refer to “Function settings and
adjustments on the combination meter
display (color LCD)”
By operating the “
” or “
” switch on the
steering wheel, you can select the menu.
Pull the “
/SET” switch to enter the
selected menu.
NOTE
If you enter the “Go Back” menu, the
system will return to the previous
screen.
!
Screen Settings
After entering the “Screen Settings” menu,
select one of the following menus.
!
Welcome Screen
The combination meter display (color
LCD), multi-function display (color LCD),
and audio/navigation unit of welcome
screen can be activated or deactivated.
!
Good-bye Screen
The good-bye screen can be activated or
deactivated.
!
Gauge Initial Movement
The movement of the meter needles and
gauge needles that occurs when the
ignition switch is turned to the “ON”
position can be activated or deactivated.
Instruments and controls/Combination meter display (color LCD)
3-38
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст