Subaru Legacy (2020 year). Manual — part 18

(255,1)

北米Model "A2570BE-A" EDITED: 2019/ 5/ 24

!

Windshield washer

To wash the windshield, pull the wiper
control lever toward you. The washer fluid
sprays until you release the lever. The
wipers operate while you pull the lever.

Windshield washer fluid warning light

NOTE

The windshield washer fluid warning
light appears when the washer fluid
level in the tank has dropped to the
lower limit. If the warning light appears,
refill the tank with fluid. For the tank
refilling method, refer to “Windshield
Washer Fluid” FP500.

&

Rear Window Wiper and
Washer Switch (Outback)

: Washer (accompanied by wiper op-

eration)

: Continuous

: Intermittent

: Off

: Washer (accompanied by wiper op-

eration)

!

Rear wiper

To turn the rear wiper on, turn the knob
switch upward.
To turn the wiper off, return the knob switch
to the “ ” position.

With the switch turned to the “

” position,

the rear wiper will operate intermittently at

– CONTINUED –

Wiper and Washer

253

3

Instruments

and

Controls

(256,1)

北米Model "A2570BE-A" EDITED: 2019/ 5/ 24

intervals corresponding to the vehicle
speed. In this position, when you move
the select lever to the “R” position, the rear
wiper will switch to continuous operation.
When you move the select lever from the
“R” (reverse) position to another position,
the rear wiper will return to intermittent
operation.

Reverse gear interlocked rear wiper:
Even if the rear wiper switch is in the off
“ ” position, if the front windshield wiper is
operating continuously, the rear wiper will
operate intermittently when you move the
select lever to the “R” (reverse) position.

The factory setting (default setting) of the
reverse gear interlocked rear wiper is as
follows.
.

U.S.-spec. models: Non-operational

.

Other models: Operational

This setting can be changed by a SUBARU
dealer. Consult your SUBARU dealer for
details.

CAUTION

Do not attach anything that disturbs
the rear wiper operation on the rear
gate. Doing so may damage the rear
wiper when it operates.

!

Washer

To wash the rear window, turn the knob to
the “

” position. The washer fluid sprays

and the wiper operates until you release
the knob.

Windshield washer fluid warning light

NOTE

The windshield washer fluid warning
light appears when the washer fluid
level in the tank has dropped to the
lower limit. If the warning light appears,
refill the tank with fluid. For the tank
refilling method, refer to “Windshield
Washer Fluid” FP500.

3-16. Defogger and Deicer

1)

Rear window defogger

2)

Outside mirror defogger (if equipped)

3)

Windshield wiper deicer (if equipped)

The defogger and deicer system is acti-

Defogger and Deicer

254

(257,1)

北米Model "A2570BE-A" EDITED: 2019/ 5/ 24

vated only when the ignition switch is in the
“ON” position.

Rear window and outside mirror (if
equipped) defogger button (dual 7.0-inch
display models)

Rear window and outside mirror defogger
button (11.6-inch display models)

To activate the defogger and deicer sys-
tem, press the rear window and outside
mirror defogger button. The rear window
defogger, outside mirror defogger and
windshield wiper deicer are activated
simultaneously. The indicator light on the
button illuminates while the defogger and
deicer system is activated.
To turn them off, press the button again.
They also turn off when the ignition switch
is turned to the “ACC” or “LOCK”/“OFF”
position.

The defogger and deicer system will
automatically shut off after approximately
15 minutes. If the rear window and outside
mirrors have been cleared and the wind-
shield wiper blade rubbers have been
deiced completely before that time, press
the button to turn them off. If defrosting,
defogging or deicing is not complete, you
have to press the button to turn them on
again.

It is possible to set the defogger and deicer
system for the continuous operation mode
by operating the center information dis-
play. For details, refer to “Car settings”
FP215 (11.6-inch display models) or
“Vehicle setting icons” FP233 (dual 7.0-
inch display models).

CAUTION

.

To prevent the battery from being

discharged, do not operate the
defogger and deicer system con-
tinuously for any longer than
necessary.

.

Do not use sharp instruments or

window cleaner containing abra-
sives to clean the inner surface of
the rear window. They may da-
mage the conductors printed on
the window.

NOTE

.

Turn on the defogger and deicer

system if the wipers are frozen to the
windshield.
.

If the windshield is covered with

snow, remove the snow so that the
windshield wiper deicer works effec-
tively.
.

While the defogger and deicer sys-

tem is in the continuous operation
mode:

– If the vehicle speed remains at 9
mph (15 km/h) or lower for 15
minutes, the windshield wiper dei-
cer system automatically stops op-
erating. However, the rear window
defogger system and outside mirror

– CONTINUED –

Defogger and Deicer

255

3

Instruments

and

Controls

(258,1)

北米Model "A2570BE-A" EDITED: 2019/ 5/ 24

defogger system maintain continu-
ous operation in this condition.
– If the vehicle battery voltage
drops below the permissible level,
continuous operation of the defog-
ger system and deicer system is
canceled and the system stops
operating.

3-17. Mirrors

Always check that the inside and outside
mirrors are properly adjusted before you
start driving.

&

Inside Mirror (without Auto-
Dimming Function) (If
Equipped)

1)

Normal position

2)

Anti-glare position

Push the tab on the mirror for normal use.
To reduce glare from the headlights of the
vehicle behind you, pull the tab to the anti-
glare position.

&

Auto-Dimming Mirror/Com-
pass with HomeLink

®

(If

Equipped)

1)

Display

2)

HomeLink

®

buttons

3)

Switch

During nighttime driving, the auto-dimming
feature senses distracting glare from
vehicle headlights behind you and auto-
matically dims to eliminate the glare and
help preserve your vision.

!

To Operate the Auto-Dimming Fea-
ture

Press the “

” switch to turn the auto-

dimming feature on/off. The auto-dimming
feature is enabled when the switch’s green
LED indicator is on. The auto-dimming
feature will default to on with each ignition

Mirrors

256

(259,1)

北米Model "A2570BE-A" EDITED: 2019/ 5/ 24

cycle.

!

To Operate the Compass Feature (if
equipped)

1. To turn the compass feature on/off,
press and hold the “

” switch for more

than 3 seconds or until the display turns
on/off. The compass feature will default to
on with each ignition cycle.
2. If the display reads “C”, slowly drive the
vehicle in circles until compass is cali-
brated.

Compass calibration zones

3. To adjust for compass zone variance:

(1) Find your current location and
zone number on the map.
(2) Press and hold the “

” switch for

more than 6 seconds or until a zone
number appears in the display.

(3) Once the zone number appears in
the display, toggle the “

” switch

again until your current location zone
number appears. After you stop press-
ing the switch, your new zone number
will be saved. Within a few seconds,
the display will show a compass direc-
tion.

4. If the vehicle’s magnetics have chan-
ged or if the compass appears inaccurate,
recalibrate the compass. Press and hold
the “

” switch for more than 9 seconds or

until a “C” appears in the display. Once a
“C” appears in the display, slowly drive the
vehicle in circles until compass is cali-
brated.

!

HomeLink

®

Wireless Control Sys-

tem

The HomeLink

®

Wireless Control System

provides a convenient way to replace up to
three hand-held radio frequency remotes
used to activate devices such as gate
operators, garage door openers, entry
door locks, security systems, even home
lighting. The below steps are generic
programming instructions; for Genie and
Sommer garage door openers please go
directly to the HomeLink

®

website. Addi-

tional information and programming vi-
deos can be found at www.HomeLink.
com and www.youtube.com/HomeLink-

Gentex.

CAUTION

.

Before programming HomeLink

®

to a garage door opener or gate
operator, make sure that people
and objects are out of the way of
the device to prevent potential
harm or damage.

.

When programming a garage

door opener, it is advised to park
outside of the garage.

.

Do not use HomeLink

®

with any

garage door opener that lacks
safety stop and reverse features
as required by U.S. federal safety
standards (this includes any gar-
age door opener model manufac-
tured before April 1, 1982). A
garage door that cannot detect
an object signaling the door to
stop and reverse does not meet
current U.S. federal safety stan-
dards.

.

It is also recommended that a new

battery be placed in the hand-
held remote (garage door opener
remote) of the device for quicker
and more accurate training.

.

Turn the ignition switch to the

“ON” or “ACC” position before

– CONTINUED –

Mirrors

257

3

Instruments

and

Controls

(260,1)

北米Model "A2570BE-A" EDITED: 2019/ 5/ 24

programming and/or operating
HomeLink

®

.

.

Keep the hand-held remote (gar-

age door opener remote) of the
device you are programming for
use in other vehicles as well as
for future HomeLink

®

program-

ming. It is also suggested that
upon the sale of the vehicle, the
programmed HomeLink

®

buttons

be erased for security purposes.
Refer to “Erasing HomeLink

®

but-

tons” FP260.

!

Programming a New HomeLink

®

button

1)

Indicator Light

2)

HomeLink

®

buttons

1. Press and release the HomeLink

®

button that you would like to program.
The HomeLink

®

indicator light will flash

orange slowly (if not, refer to “Erasing
HomeLink

®

buttons” FP260).

1)

Garage door opener remote

2. Position the hand-held remote (garage
door opener remote) 1 to 3 inches (2 to 8
cm) away from the HomeLink

®

button that

you would like to program.

NOTE

Some hand-held remotes (garage door
opener remotes) may actually train
better at a distance of 6 to 12 inches
(15 to 30 cm). Keep this in mind if you
have difficulty with the programming
process.

3. While the HomeLink

®

indicator light is

flashing orange, press and hold the hand-
held remote button. Continue pressing the
hand-held remote button until the
HomeLink

®

indicator light changes from

orange to green. You may now release the
hand-held remote button.

NOTE

Some devices may require you to re-
place this “Programming a New
HomeLink

®

button” step 3 with proce-

dures noted in the “Gate Operator /
Canadian Programming” section. Refer
to “Gate Operator/Canadian Program-
ming” FP260.

Mirrors

258

(261,1)

北米Model "A2570BE-A" EDITED: 2019/ 5/ 24

1)

Indicator Light

4. Press the HomeLink

®

button that you

would like to program and observe the
indicator light.

.

If the indicator light remains constant

green, your device should operate
when the HomeLink

®

button is

pressed. At this point, if your device
operates, programming is complete.
.

If the indicator light rapidly flashes

green, firmly press, hold for two sec-
onds and release the HomeLink

®

but-

ton up to three times to complete the
programming process. At this point if
your device operates, programming is
complete. If the device does not
operate, continue with the next step
of the programming instructions.

1)

“Learn” button

5. At the garage door opener motor,
(security gate motor, etc.) locate the
“Learn”, “Smart”, or “Program” button. This
can usually be found where the hanging
antenna wire is attached to the motor-head
unit (see the device’s manual to identify
this button). The name and color of the
button may vary by manufacturer.

NOTE

A ladder and/or second person may
simplify the following steps.

6. Firmly press and release the “Learn”,
“Smart”, or “Program” button. You now
have 30 seconds in which to complete step
7.

7. Return to the vehicle and firmly press,
hold for 2 seconds and release the
HomeLink

®

button up to three times. At

this point programming is complete and
your device should operate when the
HomeLink

®

button is pressed and re-

leased.

– CONTINUED –

Mirrors

259

3

Instruments

and

Controls

(262,1)

北米Model "A2570BE-A" EDITED: 2019/ 5/ 24

1)

Status Indicators

8. If status indicator arrows appear next
to the indicator light, please refer to
“Garage Door Two-Way Communication”
FP261.

In the event that there are still program-
ming difficulties or questions, additional
HomeLink

®

information and programming

videos can be found at
www.HomeLink.com and
www.youtube.com/HomeLinkGentex. For
Genie and Sommer garage door openers
please go directly to the HomeLink

®

website.

!

Gate Operator/Canadian Pro-
gramming

Canadian radio-frequency laws require
transmitter remote signals to “time-out”
(or quit) after several seconds of transmis-
sion, which may not be long enough for
HomeLink

®

to pick up the signal during

programming. Similar to this Canadian
law, some U.S. gate operators are de-
signed to “time-out” in the same manner.
The indicator LED on the hand-held
remote will go off when the device times
out, indicating that it has finished transmit-
ting.

If you live in Canada or you are having
difficulties programming a gate operator or
garage door opener by using the program-
ming procedures, replace “Programming a
New HomeLink

®

button” step 3 with the

following:

While the HomeLink

®

indicator light is

flashing orange, press and release (“cy-
cle”) your device’s hand-held remote every
two seconds until the HomeLink

®

indicator

light changes from orange to green. You
may now release the hand-held remote
button.

NOTE

If programming a garage door opener
or gate operator, it is advised to unplug

the device during the “cycling” process
to prevent possible overheating.

Proceed with “Programming a New
HomeLink

®

button” step 4 to complete.

!

Using HomeLink

®

To operate, simply press and release the
programmed HomeLink

®

button. Activa-

tion will now occur for the trained device
(i.e. garage door opener, gate operator,
security system, entry door lock, home/
office lighting, etc.). For convenience, the
hand-held remote of the device may also
be used at any time.

!

Erasing HomeLink

®

buttons

To erase programming from the three
buttons (individual buttons cannot be
erased but can be “reprogrammed” as
outlined below), follow the step noted:

Press and hold the two outer HomeLink

®

buttons for at least 10 seconds. The LED
indicator will change from continuously lit
to rapidly flashing. Release both buttons.
Do not hold for longer than 20 seconds.
HomeLink

®

is now ready to be pro-

grammed at any time beginning with
“Programming a New HomeLink

®

button”

- step 1.

Mirrors

260

(263,1)

北米Model "A2570BE-A" EDITED: 2019/ 5/ 24

!

R e p r o g r a m m i n g a S i n g l e
HomeLink

®

button

To program a previously trained button,
follow these steps:
1. Press and hold the desired HomeLink

®

button. DO NOT release the button.
2. The indicator light will begin to slowly
flash orange after 20 seconds. The
HomeLink

®

button can be released at this

point. Proceed with “Programming a New
HomeLink

®

button” - step 3.

3. If you do not complete the program-
ming of a new device to the button, it will
revert to the previously stored program-
ming.

!

Garage Door Two-Way Commu-
nication

HomeLink

®

has the capability of commu-

nicating with your garage door opener.
HomeLink

®

can receive and display “clos-

ing” or “opening” status messages from
compatible garage door opener systems.
At any time, HomeLink

®

can also recall and

display the last recorded status commu-
nicated by the garage door opener to
indicate your garage door being “closed”
or “opened”.

HomeLink

®

has the capability of receiving

this communication from the garage door
opener at a range up to 820 feet (250 m).

Range may be reduced by obstacles such
as houses or trees. You may have to slow
your vehicle speed to successfully receive
the garage door opener communication.

!

Programming Two-Way Commu-
nication

1)

Status Indicators

Within 5 seconds after programming a new
HomeLink

®

button, both of HomeLink’s

garage door status indicators will flash
rapidly green indicating that the garage
door two-way communication has been
enabled. If your garage door status in-
dicators flashed, two-way communication
programming is complete.

If the garage door status indicators do not
flash, additional HomeLink

®

information

and programming videos can be found

online at www.HomeLink.com and
www.youtube.com/HomeLinkGentex.

!

Using Two-Way Communication

1)

Status Indicator

Recall and display (at any time) the last
recorded garage door status message
communicated to HomeLink

®

by simulta-

neously pressing HomeLink

®

buttons 1

and 2 for 2 seconds. HomeLink

®

will

display the last recorded status for 3
seconds.
If two-way communication programming is
successful, HomeLink

®

will display the

status of your garage door opener with
arrow indicators (see below).

– CONTINUED –

Mirrors

261

3

Instruments

and

Controls

(264,1)

北米Model "A2570BE-A" EDITED: 2019/ 5/ 24

1)

Garage Door Opener CLOSING (Blinking
Orange)

2)

Garage Door Opener CLOSED (Solid
Green)

3)

Garage Door Opener OPENING (Blink-
ing Orange)

4)

Garage Door Opener OPENED (Solid
Green)

!

Certification

In the event that there are still program-
ming difficulties or questions, additional
HomeLink

®

information and programming

videos can be found at
www.HomeLink.com,
www.youtube.com/HomeLinkGentex, or
by calling the toll-free HomeLink-hotline
at 1-800-355-3515.

.

U.S.-spec. models

CAUTION

FCC WARNING

Changes or modifications not ex-
pressly approved by the party re-
sponsible for compliance could void
the user’s authority to operate the
equipment.

Mirrors

262

(265,1)

北米Model "A2570BE-A" EDITED: 2019/ 5/ 24

.

Canada-spec. models

HomeLink

®

and the HomeLink

®

house are

registered trademarks of Gentex Corpora-
tion.

WARNING

.

W h e n

p r o g r a m m i n g

t h e

HomeLink

®

Wireless Control Sys-

tem, you may be operating a
garage door opener or other
device. Make sure that people
and objects are out of the way of
the garage door or other device
to prevent potential harm or da-
mage.

.

Do not use the HomeLink

®

Wire-

less Control System with a gar-
age door opener that lacks the
safety stop and reverse feature
as required by applicable safety
standards. A garage door opener
which cannot detect an object,
signaling the door to stop and
reverse, does not meet these
safety standards. Using a garage
door opener without these fea-
tures increases risk of serious
injury or death. For more infor-
mation, consult the HomeLink

®

website at www.homelink.com or
call 1-800-355-3515.

– CONTINUED –

Mirrors

263

3

Instruments

and

Controls

(266,1)

北米Model "A2570BE-A" EDITED: 2019/ 5/ 24

&

Outside Mirrors

!

Convex mirror (passenger side)

WARNING

Objects look smaller in a convex
mirror and farther away than when
viewed in a flat mirror. Do not use the
convex mirror to judge the distance
of vehicles behind you when chan-
ging lanes. Use the inside mirror (or
glance backwards) to determine the
actual size and distance of objects
that you view in convex mirror.

CAUTION

Make sure to adjust the mirrors
before driving.

!

Remote control mirror switch

: Select side to adjust
: Direction control

The remote control mirrors operate when
the ignition switch is in the “ON” or “ACC”
position.
1. Turn the control switch to the side that
you want to adjust. “L” is for the left mirror,
“R” is for the right mirror.
2. Move the control switch in the direction
you want to move the mirror.
3. Return the control switch to the neutral
position to prevent unintentional opera-
tion.

NOTE

.

The mirrors can also be adjusted

manually.

For models with memory function:
.

The outside mirror can be adjusted

for approximately 45 seconds after the
following conditions are met.

– The ignition switch is turned to
the “OFF” position.
– The door is unlocked using the
access key fob.

.

The outside mirror angle can be

registered with button “1”, “2” or each
of the key fobs. For details, refer to
“Power driver’s seat with synchronized
outside mirrors memory function”
FP33.

!

Reverse tilt-down feature (if
equipped)

When backing the vehicle up, the right
and/or left outside mirrors will turn down-
ward automatically to provide better rear
visibility.
1.

Push the ignition switch to the ON

position.
2. Move the select lever to the R (Re-
verse) position.
3. The outside mirror surface moves
downward.

The outside mirror surface will return to its
original position when the following condi-
tion are met.
.

Approximately 9 seconds after the

Mirrors

264

(267,1)

北米Model "A2570BE-A" EDITED: 2019/ 5/ 24

select lever is moved to any position other
than R (Reverse).
.

The ignition switch is turned to the

“OFF” position.
.

The vehicle is running.

NOTE

.

The reverse tilt-down mirror angle

can be registered with button “1”, “2”
or each of the key fobs. For details,
refer to “Power driver’s seat with
synchronized outside mirrors memory
function” FP33.
.

The operational/non-operational

setting can be changed by operating
the center information display. For de-
tails, refer to “Car settings” FP215.
.

The factory setting (default setting)

for this function is set as the front
passenger’s side mirror. The setting of
driver’s side mirror operation can be
changed by a SUBARU dealer. Contact
your SUBARU dealer for details.

CAUTION

Depress the brake pedal during the
reverse tilt-down mirror angle ad-
justment.

To adjust the reverse tilt-down mirror
angle, adjust the outside mirror using the

remote control mirror switch while the
reverse tilt-down operates. For details
about how to adjust the outside mirror
angle, refer to “Remote control mirror
switch” FP264.
Memory function:
The angle of the reverse tilt-down mirror
can be registered. Register the position
with button “1”, “2” or each of the access
key fobs and retrieve the position.
For details about registration or retrieval of
a position, refer to “Power driver’s seat
with synchronized outside mirrors memory
function” FP33.

NOTE

If the seat is moved forward or back-
ward 1.18 in (30 mm) or more, the
reverse tilt-down will move to the
factory default position or the last
position hold.

Hold last position function:
The angle of the reverse tilt-down mirror
can be set to the latest adjusted angle.
The hold last position function operates
when the following condition are met.
.

The memory function is not used.

.

The seat is moved forward or backward

1.18 in (30 mm) or more.

NOTE

.

The factory setting (default setting)

for this function is set as “non-opera-
tional”. This setting can be changed to
“operational” at SUBARU dealers. For
more details, contact a SUBARU dealer.
.

If the hold last position function

setting is “non-operation”, the reverse
tilt-down will move to the factory de-
fault position.

!

Power folding mirror switch (if
equipped)

The power folding mirror switch operates
when the ignition switch is in the “ON” or
“ACC” position.
To fold the outside mirrors, press the
power folding mirror switch. To unfold the
mirrors, press the switch again.

– CONTINUED –

Mirrors

265

3

Instruments

and

Controls

(268,1)

北米Model "A2570BE-A" EDITED: 2019/ 5/ 24

NOTE

.

If the outside mirrors have been

operated (folded or unfolded) manually,
when you turn the ignition switch from
the “LOCK”/“OFF” position to the
“ACC” or “ON” position, the outside
mirrors may be adjusted automatically
depending on the status of the power
folding mirror switch.
.

If the outside mirrors have been

manually folded slightly forward of the
regularly unfolded position, when you
turn the ignition switch from the
“LOCK”/“OFF” position to the “ACC”
or “ON” position, the outside mirrors
may automatically fold further forward
depending on the status of the power
folding mirror switch. When this hap-
pens, press the power folding mirror
switch. By doing so, the outside mir-
rors which have been folded to the
furthest forward position will extend to
the regularly unfolded position and
then fold rearward in the usual way. In
order to unfold the outside mirrors,
press the switch again.
.

When you fold the outside mirrors

manually, the mirrors may not unfold
when the switch is pressed, even
though the motor operating sound is
heard. When this happens, operate the
power folding mirror switch again.

.

When you unfold the outside mirrors

manually, the mirrors may become
wobbly. Be sure to unfold the mirrors
by operating the switch. If the outside
mirrors are still wobbly, fold the mirrors
again and then unfold them by operat-
ing the switch again.
.

When the temperature is low, the

outside mirrors may stop during opera-
tion. Push the switch again. When the
outside mirrors do not work by operat-
ing the switch, move the outside mir-
rors several times manually. This
makes it possible to operate them by
switch operation.
.

When you operate the power folding

mirror switch continuously, it may not
work. This is not a malfunction. Operate
after waiting for a short period of time.
.

The outside mirrors can be operated

(folded or unfolded) manually for ap-
proximately 45 seconds after the fol-
lowing conditions are met.

– The ignition switch is turned to
the “OFF” position.
– The door is unlocked using the
access key fob.

!

Power folding door mirror func-
tion

The mirrors are automatically folded when
the power folding mirror switch is in the

mirror unfolding position, the ignition
switch is turned OFF, and the doors are
locked.
The mirrors are automatically unfolded
when the power folding mirror switch is in
the mirror unfolding position and the doors
are unlocked.

NOTE

.

The power folding door mirror func-

tion does not operate when the power
folding mirror switch is in the mirror
unfolding position.
.

The setting of the Power folding

door mirrors function can be changed
by your SUBARU dealer. Contact your
SUBARU dealer for details. Also, the
setting of the Power folding door
mirrors operation can be changed by
operating the center information dis-
play. For details, refer to “Car settings”
FP215.

Mirrors

266

(269,1)

北米Model "A2570BE-A" EDITED: 2019/ 5/ 24

3-18. Tilt/Telescopic Steering
Wheel

WARNING

.

Do not adjust the steering wheel

tilt/telescopic position while driv-
ing. This may cause loss of
vehicle control and result in per-
sonal injury.

.

If the lever cannot be raised to the

fixed position, adjust the steering
wheel again. It is dangerous to
drive without locking the steering
wheel. This may cause loss of
vehicle control and result in per-
sonal injury.

1)

Tilt adjustment

2)

Telescopic adjustment

1. Adjust the seat position. Refer to “Front
Seats” FP28.
2. Pull the tilt/telescopic lock lever down.
3. Move the steering wheel to the desired
level.
4. Pull the lever up to lock the steering
wheel in place.
5. Make sure that the steering wheel is
securely locked by moving it up and down,
and forward and backward.

3-19. Heated Steering Wheel
System (If Equipped)

The Heated Steering Wheel system
warms the steering wheel at a constant
temperature.

1)

Heated Steering Wheel switch

2)

Indicator light

3)

Heated area

To turn on the Heated Steering Wheel
system, pull the Heated Steering Wheel
switch when the ignition switch is in the
“ACC” or “ON” position. Then the steering
wheel will be warmed and the indicator
light on the switch will illuminate. To turn off
the Heated Steering Wheel system, pull
the switch again. Then the indicator light
will turn off.

– CONTINUED –

Tilt/Telescopic Steering Wheel

267

3

Instruments

and

Controls

(270,1)

北米Model "A2570BE-A" EDITED: 2019/ 5/ 24

CAUTION

.

Use the Heated Steering Wheel

system with the engine running.
Otherwise, the battery voltage
may drop below the permissible
level and it may not be possible to
start the engine.

.

There is a possibility that people

with delicate skin may suffer
slight burns even at low tempera-
tures if they use the Heated
Steering Wheel for a long period
of time. When using the Heated
Steering Wheel, always be sure to
warn the persons concerned.

.

Do not cover the Heated Steering

Wheel with an object such as a
steering wheel cover. Doing so
may cause the Heated Steering
Wheel to overheat.

NOTE

.

If the surface temperature of the

steering wheel is approximately above
1048F (408C) when the Heated Steering
Wheel system is turned on, the system
will not heat the steering wheel. Then,
the indicator light will continue to
illuminate.
.

The Heated Steering Wheel system

will automatically turn off approxi-
mately 30 minutes after the system
has been turned on.

3-20. Horn

To sound the horn, push the horn pad.

Horn

268