Subaru Outback (2022 year). Manual in english — page 10
(150,1)
.
Passenger ’s side power window
switches:
Each passenger’s window can be con-
trolled by the power window switch located
on the door.
The switch illuminates when operated.
!
Operating the window
With one-touch auto up and down feature
1)
Automatically close*
2)
Close
3)
Open
4)
Automatically open*
*: To stop the window halfway, operate the
switch to the opposite side.
Without one-touch auto up and down
feature
1)
Close
2)
Open
NOTE
Avoid the following.
.
Continuously operating a switch in
the same direction after the window is
fully closed or fully opened.
.
Continuously operating three or
more switches all at once in the same
direction after the windows are fully
closed or fully opened.
Either of the operations described
above may cause the power window
breaker to operate making it impossible
to open or close the window. Be sure to
initialize the power windows. Refer to
Windows
148
(151,1)
“Initialization of Power Window (Win-
dows with One-Touch Auto up and
down Function)”
!
Anti-entrapment function (windows
with one-touch auto up and down
function)
While closing the window automatically, if
the window senses a substantial enough
object trapped between the window and
the window frame, it automatically moves
down slightly and stops.
If a foreign object is caught while window is
opening automatically, the window will
stop.
CAUTION
.
Never attempt to test the power
window operation using body
parts.
.
If an object is caught just before
the window fully closes, the sys-
tem may not operate properly.
NOTE
.
If a window detects an impact similar
to that caused by trapping an object (for
example, when the vehicle encounters
a deep pothole), the anti-entrapment
function may operate.
.
You cannot close the window for a
few seconds after the anti-entrapment
function operates.
!
Off delay function (windows with
one-touch auto up and down func-
tion)
The windows can be operated for approxi-
mately 40 seconds even after the ignition
switch is turned to the “ACC” or “OFF”
position. If a front door is opened within 40
seconds, the off delay function is can-
celed.
!
Locking the passengers’ windows
1)
Lock
2)
Unlock
When the lock switch is in the lock position,
the rear passenger’s window switches on
the driver side door and the passengers’
window switches cannot be operated.
When the indicator on the window
switches does not illuminate, the window
switch cannot be operated.
&
Initialization of Power Win-
dow (Windows with One-
Touch Auto up and down
Function)
If the one-touch auto up and down function
or off delay function does not operate
properly, operate each window according
to the following procedure in order to
initialize the power window system.
1. Close the door.
2. Turn the ignition switch to the “ON”
position.
3. Open the window completely and then
press and hold down the power window
switch for approximately 1 second.
4. Close the window completely and then
pull and hold the power window switch for
approximately 1 second.
Windows
149
2
Keys
and
Doors
(152,1)
2-9. Trunk Lid (Legacy)
WARNING
.
To prevent dangerous exhaust
gas from entering the vehicle,
always keep the trunk lid closed
while the engine is running.
.
Check that the trunk is comple-
tely closed before driving. If it is
not, it may suddenly open, which
could lead to an accident.
.
Help prevent children, adults or
animals from locking themselves
in the trunk. On hot or sunny
days, the temperature in the trunk
could quickly become high en-
ough to cause death or serious
heat-related injuries including
brain damage to anyone locked
inside, particularly for small chil-
dren.
.
When leaving the vehicle, close
all windows and lock all doors.
Also make certain that the trunk
is closed.
CAUTION
.
Be extremely careful not to catch
fingers or other objects when
closing the trunk lid.
.
Before opening and closing the
trunk, carefully check your sur-
roundings to make sure it will not
strike any people or objects.
.
When loading and unloading car-
go, be careful not to come in
contact with the hot engine ex-
haust gas or the exhaust pipe,
because they could burn you.
.
Be careful when opening the
trunk in a strong wind. The trunk
lid could open or close suddenly
and cause injuries.
.
Make sure that the trunk is com-
pletely open when using it. If it is
not, the trunk lid may suddenly
drop and cause serious injury.
.
Remove snow and ice from the
trunk lid before opening it. Not
doing so could cause the trunk
lid to fall after it is opened.
.
Do not push the trunk lid forcibly
to close it. It could deform the
metal.
.
Under the following conditions,
the trunk lid may close unexpect-
edly, striking people or objects in
its path:
– Parking on a slope, with the
rear of the vehicle lower than
its front. In this case, make
sure the trunk lid is fully open
and secure before loading or
unloading cargo.
– Installing parts or accessories
that place excess weight on
the trunk lid. Install only gen-
uine SUBARU parts and ac-
cessories.
– Loading baggage or other
heavy items by throwing or
otherwise forcefully loading
them into the trunk. Always
load cargo with care.
&
To Open and Close the Trunk
Lid from Outside
The trunk lid can be opened using the
keyless access function or remote keyless
entry system. For details, refer to the
following section.
.
For models with “keyless access with
push-button start system”, refer to “Open-
ing trunk (Legacy)”
Trunk Lid (Legacy)
150
(153,1)
.
For models without “keyless access
with push-button start system”, refer to
“Opening the Trunk Lid (Legacy)”
To close the trunk lid, lightly press the trunk
lid down until the latch engages.
NOTE
.
Do not leave your valuables in the
trunk when you leave your vehicle.
.
Under the following conditions, the
trunk can be opened without the access
key fob.
– The trunk lock/unlock setting is
set to on.
– All doors are unlocked.
The trunk lock/unlock setting can be
changed by a SUBARU dealer. Contact
your SUBARU dealer to change the
setting.
&
To Open the Trunk Lid from
Inside
Press and hold the trunk lid opener button
for more than 1 second.
&
Internal Trunk Lid Release
Handle
The internal trunk lid release handle is a
device designed to open the trunk lid from
inside the trunk. In the event children or
adults become locked inside the trunk, the
handle allows them to open the lid. The
handle is located on the inside of the trunk
lid.
To open the trunk lid from inside the trunk,
pull the yellow handle as indicated by the
arrow on the handle. This operation
unlocks the trunk lid. Then, push up the lid.
The handle is made of material that
remains luminescent for approximately
an hour in the dark trunk space after it is
exposed to ambient light even for a short
time.
– CONTINUED –
Trunk Lid (Legacy)
151
2
Keys
and
Doors
(154,1)
WARNING
Never allow any child to get in the
trunk and play with the release
handle. If the driver starts the vehi-
cle without knowing that a child is
inside the trunk and the child opens
the lid using the release handle, the
child could fall out and be killed or
seriously injured.
CAUTION
.
Do not close the lid while gripping
the release handle. The handle
may be damaged.
.
Do not use the handle as a hook
to fasten straps or ropes to
secure your cargo in the trunk.
Such use may result in damage of
the handle.
.
Load the trunk so that cargo
cannot strike the release handle.
If the cargo hits the handle while
the vehicle is being driven, the
handle may be pulled and the
trunk lid may open. That may
cause cargo to fall out of the
trunk, which could create a traffic
safety hazard.
!
Inspection
Perform the following steps at least twice a
year to check the release handle for
correct operation.
1. Open the trunk lid.
2. To lock it, press the latch with the
screwdriver shaft until it clicks.
This places the latch in the locked position.
3. Move the release handle, from outside
the vehicle, in the direction of the arrow to
check if the latch is released.
Trunk Lid (Legacy)
152
(155,1)
If the latch is not released, contact your
SUBARU dealer.
In that case, use the key to release the
latch, then close the trunk lid.
Also, if the movement of the release
handle feels restricted or not entirely
smooth during operation, or the handle
and/or handle base is cracked, contact
your SUBARU dealer.
2-10. Rear Gate (Outback/
Subaru Outback Wilderness)
CAUTION
When loading and unloading cargo,
be careful not to come in contact
with the hot engine exhaust gas or
the exhaust pipe, because they
could burn you.
&
Manual Rear Gate
The rear gate can be locked and unlocked
using any of the following systems.
.
Power door locking switch: Refer to
“Locking and Unlocking from the Inside”
.
Keyless access with the push-button
start system (if equipped): Refer to “Key-
less Access with Push-Button Start Sys-
tem”
.
Remote keyless entry system: Refer to
To open:
Rear gate opener button
1. Unlock the rear gate.
2. Press and hold the rear gate opener
button. The rear gate will open slightly.
3. Hold the rear gate and lift it up slowly.
NOTE
If the rear gate cannot be opened due to
a discharged vehicle battery, a mal-
function in the door locking/unlocking
system or other causes, you can unlock
it by manually operating the rear gate
lock release lever. For the procedure,
refer to “Rear Gate (Outback/Subaru
Outback Wilderness) – If the Rear Gate
Cannot Be Opened”
– CONTINUED –
Rear Gate (Outback/Subaru Outback Wilderness)
153
2
Keys
and
Doors
(156,1)
To close:
Lower the rear gate slowly and push down
firmly until the latch engages.
The rear gate can be lowered easily if you
pull it down holding the convenient grip.
WARNING
.
To prevent dangerous exhaust
gas from entering the vehicle,
always keep the rear gate closed
while the engine is running.
.
Do not attempt to shut the rear
gate while holding the recessed
grip. Also do not close the rear
gate by pulling the grip from
inside the cargo space. There is
a danger of your hand being
caught and injured.
CAUTION
.
Do not jam a plastic bag in or
place cellophane tape on the rear
gate stays or scratch the stays
while loading or unloading cargo.
That could cause leakage of gas
from the stays, which may result
in their inability to hold the rear
gate open.
.
Be careful not to hit your head or
face on the rear gate when open-
ing or closing the rear gate and
when loading or unloading cargo.
&
Power Rear Gate (If
Equipped)
WARNING
.
When operating the power rear
gate, observe the following pre-
cautions. Ignoring the precau-
tions may result in an injury (e.g.,
anyone’s body is hit against the
rear gate or is caught in the rear
gate, etc.)
– Make sure there are no people
around the rear gate.
– Never let anyone get close to
the rear gate.
.
When closing the rear gate, be
extremely careful to prevent any-
one’s fingers, arms, neck, head
or other objects from being
caught in the rear gate. Other-
wise, serious personal injury may
be caused by entrapment.
.
After opening the rear gate on a
slope by using the power rear
gate feature, the rear gate may
close. Make sure that the rear
gate has stopped completely
after opening it.
.
When leaving the vehicle, always
carry the key for safety and never
allow an unattended child to
remain in the vehicle. Failure to
follow this procedure could re-
sult in injury to a child operating
the power rear gate.
.
The driver should be aware of and
pay careful attention to his/her
responsibilities.
Rear Gate (Outback/Subaru Outback Wilderness)
154
(157,1)
.
Use the power rear gate only
when the area around the rear
gate is clearly visible and when
you have checked that there is no
danger of people being caught in
the gate.
CAUTION
.
When closing the rear gate after
opening it, make sure to use the
power rear gate. If you close the
rear gate manually with extra
force, the power rear gate may
be damaged.
.
Do not install any accessories
other than genuine SUBARU
parts on the rear gate. If the
weight of rear gate increases
excessively, the rear gate stay
cannot support the rear gate
sufficiently when opening the
rear gate. Also, the power rear
gate may not function properly or
may malfunction.
The power rear gate operates only when
all of the following conditions are satisfied.
.
The vehicle is stopped completely.
.
The outside temperature is within a
range from −22
8
F to 140
8
F (from −30
8
C to
60
8
C).
.
The ignition switch is in the “OFF” or
“ACC” position. Or, the ignition switch is in
the “ON” position and the select lever is in
the “P” position.
We recommend using the power rear gate
function in most circumstances instead of
manual operation.
NOTE
.
The rear gate may not move
smoothly when the battery power be-
comes low.
.
Do not press the power rear gate
button repeatedly while the power rear
gate is operating. Otherwise, the sys-
tem may ignore the button operation in
order to avoid being damaged.
.
If the vehicle starts to move while the
power rear gate is operating, the sys-
tem sounds a buzzer and closes the
rear gate automatically. At this time, if
the system detects jamming, it will
deactivate the power rear gate and the
rear gate will not be closed. If this
occurs, close the rear gate manually.
For details, refer to “Manual Rear Gate”
.
If you try to open the rear gate using
the power rear gate function immedi-
ately after closing the rear gate using
the power rear gate function, an elec-
tronic chirp will sound and the rear gate
will not open. Wait for a while before
trying to open the rear gate via the
power rear gate function.
.
If either of the operating conditions
has not been satisfied while operating
the power rear gate, an electronic chirp
will sound and the power rear gate will
be deactivated. In this case, the rear
gate may stop opening or closing
suddenly.
!
Operation
NOTE
.
The rear gate will remain unlocked
even after closing it. Always lock the
rear gate when leaving the vehicle.
.
If you cannot open/close the rear
gate by performing the operation de-
scribed here, a short electronic chirp
will sound three times (beep, beep,
beep). In this case, perform the initiali-
zation of the power rear gate. Refer to
“Initialization of power rear gate”
– CONTINUED –
Rear Gate (Outback/Subaru Outback Wilderness)
155
2
Keys
and
Doors
(158,1)
!
By the power rear gate button
(other than the buttons on the
rear gate)
Power rear gate button on the instrument
panel
Power rear gate button on the access key
fob
To open the rear gate:
Press and hold the power rear gate button
when the rear gate is closed. The rear gate
will open automatically. Then an electronic
chirp and the hazard warning flashers will
operate as follows:
.
When operating the power rear gate
button on the instrument panel: sounds
and flashes twice.
.
When operating the power rear gate
button on the access key fob: sounds and
flashes four times.
NOTE
.
If you cannot open the rear gate by
operating the power rear gate button on
the instrument panel, then it may be
locked by using the keyless access
function or the remote keyless entry
system. Unlock the doors using the
keyless access function or the remote
keyless entry system before pressing
the power rear gate button again.
.
The factory setting (default setting)
of the operation for the “
” button on
the access key fob or the transmitter is
pressing and holding. This setting can
be changed to non-operation or press-
ing twice at SUBARU dealers. For more
details, contact a SUBARU dealer.
To pause the opening rear gate:
Briefly press the power rear gate button
while the rear gate is being opened. Then
an electronic chirp will sound twice and the
hazard warning flashers will flash twice.
If you press the power rear gate button
again, the rear gate will close.
You can open the rear gate by pressing the
power rear gate button briefly while the
rear gate is being closed.
Rear Gate (Outback/Subaru Outback Wilderness)
156
(159,1)
NOTE
The rear gate cannot be paused when it
is in the approximately 2 in (5 cm) range
from the fully closed position. The
system will ignore any button operation
and the rear gate will continue to open.
To close the rear gate:
Press and hold the power rear gate button.
Then an electronic chirp will sound twice
and the hazard warning flashers will flash
twice. If you briefly press the power rear
gate button again, the rear gate will open.
!
By the buttons on the rear gate
NOTE
After performing the following proce-
dures, an electronic chirp will sound
twice and the hazard warning flashers
will flash twice.
Rear gate opener button
Power rear gate button on the inside edge
of the rear gate
1)
Power rear gate lock button
2)
Power rear gate button
To open the rear gate:
1. For models with “keyless access with
push-button start system”, carry the ac-
cess key fob. For models without “keyless
access with push-button start system”,
unlock the rear gate.
2. Briefly press the rear gate opener
button when the rear gate is closed.
The rear gate will open automatically.
To pause the opening rear gate:
Briefly press either of the following buttons
while the rear gate is being opened.
.
Rear gate opener button
– CONTINUED –
Rear Gate (Outback/Subaru Outback Wilderness)
157
2
Keys
and
Doors
(160,1)
.
Power rear gate button on the inside
edge of the rear gate
If you press the power rear gate button
again, the rear gate will close. You can
open the rear gate by pressing the power
rear gate button briefly while the rear gate
is being closed.
NOTE
The rear gate cannot be paused when it
is in the approximately 2 in (5 cm) range
from the fully closed position. The
system will ignore any button operation
and the rear gate will continue to open.
To close the rear gate:
Briefly press either of the following but-
tons.
.
Rear gate opener button
.
Power rear gate button on the inside
edge of the rear gate
If you press the power rear gate button
again, the rear gate will open.
To Lock the doors using the power rear
gate lock button:
Carry the access key fob, and press the
power rear gate lock button. All doors, the
rear gate and the fuel filler lid are locked,
and the rear gate will be closed. Also, the
hazard warning flashers will flash once,
and an electronic chirp will sound once.
NOTE
.
By pushing the power rear gate lock
button for more than 2 seconds, all
doors are locked, however, the auto
closing function of the rear gate will be
canceled.
.
If any of the doors is not fully closed,
the electronic chirp sounds five times
to alert you that the doors are not
properly closed.
!
By manual operation
To open the rear gate:
Lift up the rear gate, when the rear gate is
at the midway position. The rear gate will
open automatically.
To close the rear gate:
Pull down the rear gate when the rear gate
is opened. The rear gate will close auto-
matically.
NOTE
.
If the rear gate is moved slowly, it
may not operate automatically open or
close.
.
When leaving the vehicle, make sure
that all doors and the rear gate are
completely locked.
!
Memory function
The preferred rear gate height can be
registered.
!
Registration of the rear gate
height
To register the rear gate height, perform
the following procedures.
1. Open the rear gate and stop it at the
preferable height.
Rear Gate (Outback/Subaru Outback Wilderness)
158
(161,1)
1)
Power rear gate button
2. Press and hold the power rear gate
button to register the height. An electronic
chirp sounds and the hazard warning
flashes for confirmation.
The rear gate will stop at the registered
position when the memory function is on.
NOTE
.
Register the rear gate height to turn
on the “Power Rear Gate Memory”
automatically. For details, refer to “Car
settings”
.
To change the registered height,
perform the registering procedure
again.
.
It is possible to register the height
from approximately 2 in (5 cm) or more
from the completely closed position.
!
Deactivation of the memory func-
tion
Deactivate the memory function to open
the rear gate fully. Perform either of the
following operation to deactivate the mem-
ory function.
– Deactivate the “Power Rear Gate
Memory” function on the center informa-
tion display (CID). Refer to “Car settings”
– Register the position of the rear gate at
the fully open position.
!
Utilizing the memorized rear gate
height
To open the rear gate and stop it at the
registered height, perform the following
procedure.
1. Check that “Power Rear Gate Memory”
is on. Refer to “Car settings”
2. Press and hold any of the power rear
gate button.
NOTE
The rear gate will open to the position
that is stored in the memory function
even if the rear gate is opened by the
reverse function.
!
Reverse function
WARNING
.
Do not let parts of your body get
caught when operating the re-
verse function. If the reverse
function does not operate for
some reason, this may lead to
serious injury or accidents.
.
The reverse function may not
operate if foreign objects are
caught in the rear gate just before
it closes completely. Be careful
not to catch your fingers and
other body parts.
.
The reverse function may not
operate depending on the object
shape and the manner in which it
was caught. Be careful not to
catch your fingers and other
body parts.
CAUTION
.
If the reverse function is operated
3 times consecutively, automatic
opening and closing of the power
rear gate function will be can-
celed and the rear gate will stop
opening or closing suddenly.
– CONTINUED –
Rear Gate (Outback/Subaru Outback Wilderness)
159
2
Keys
and
Doors
(162,1)
However, the rear gate may open
or close depending on the rear
gate height when automatic op-
eration is ceased. Be careful that
the rear gate does not hit any-
one’s head or face, etc. and that
fingers and baggage, etc. are not
caught in it.
.
Take care not to damage the
touch sensors. Otherwise, the
reverse function may cease to
operate.
If, while opening or closing using power
rear gate, the rear gate catches persons or
baggage or hits an obstacle, an electronic
chirp will sound 3 times and the rear gate
will operate as follows.
When opening the rear gate:
The rear
gate will automatically close.
When closing the rear gate:
The rear
gate will automatically open.
1)
Touch sensor
Touch sensors are attached on the left and
right edges of the rear gate. If the touch
sensors detect fingers, baggage, etc.
while closing by the power rear gate
function, an electronic chirp will sounds 3
times and the rear gate will open auto-
matically.
NOTE
When the rear gate is opened using the
reverse function, it will be opened fully
or to the height registered in the
memory function.
!
Rear gate drop prevention function
If, while fully opened via the power rear
gate function, the rear gate is lowered by
the weight of snow and such, an electronic
chirp will sound and the rear gate drop
prevention function will apply braking to
the rear gate so that it prevents a rapid
closure of the rear gate.
NOTE
.
If there is snow on the rear gate, only
use the power rear gate function after
removing the snow.
.
If you close the rear gate manually
just after the rear gate is fully opened
using the power rear gate function, the
rear gate drop prevention function will
detect a rapid closure of the rear gate
and apply braking to the rear gate. In
this case, this is not a malfunction.
!
Selecting audible signal operation
Using an electronic chirp, the power rear
gate will give you an audible signal before
starting its operation. If desired, the audi-
ble signal can be turned off by a SUBARU
dealer. Consult your SUBARU dealer for
details.
For models with “keyless access with
push-button start system”, you can also
turn the audible signal off by operating the
center information display. For details,
refer to “Car settings”
The ON/OFF setting of the audible signal
also works as the audible signal settings
Rear Gate (Outback/Subaru Outback Wilderness)
160
(163,1)
for the “remote keyless entry system” and
the “keyless access with push-button start
system”. However, for the electronic chirp
such as that caused by “Reverse function”
P159 or “Rear gate drop prevention
P160, it cannot be set as non-
operational.
!
Initialization of power rear gate
If the power rear gate detects some
abnormality while operating, an electronic
chirp will sound and the power rear gate
operation will be automatically stopped in
either opening or closing position. In this
case, the system needs to be initialized in
the following order to restart the function
properly.
!
If the power rear gate is closed
1. Keep pressing the rear gate opener
button until it is unlocked (for approxi-
mately 5 seconds) and lift up the rear gate.
2. Pull down the rear gate until it starts to
close automatically. The system will be
initialized once the gate is fully closed.
3. Operate the power rear gate and check
that the function operates properly.
!
If the power rear gate is opened
1. Pull down the rear gate until it starts to
close automatically. The system will be
initialized once the gate is fully closed.
If the rear gate will not close completely,
keep pressing the rear gate opener button
for approximately 5 seconds and pull down
the rear gate.
2. Operate the power rear gate and check
that the function operates properly.
CAUTION
If the power rear gate function does
not operate properly, have your
vehicle checked by a SUBARU deal-
er.
!
Hands-free Power Rear Gate func-
tion
The Hands-free Power Rear Gate function
enables the rear gate to be opened
automatically by holding a hand over the
rear emblem.
This function can be deactivated using the
Hands-free Power Rear Gate off switch.
Refer to “Hands-free Power Rear Gate off
switch”
CAUTION
Do not remove the rear emblem or
decorate it or the area around it.
Doing so could lead to a malfunction
of the Hands-free Power Rear Gate
function.
To open the rear gate via the function,
perform the following steps.
1. When the ignition switch is in the OFF
position, carry the access key fob.
– CONTINUED –
Rear Gate (Outback/Subaru Outback Wilderness)
161
2
Keys
and
Doors
(164,1)
2. Move your hand slowly toward the rear
emblem and hold it there until a electronic
chirp sounds.
3. Immediately after the electronic chirp
sounds, move your hand away.
4. The rear gate will open automatically.
NOTE
.
It is possible to open the rear gate by
moving close to the rear emblem.
.
The Hands-free Power Rear Gate
function will not operate when the rear
gate has already been opened.
.
If any of the following are performed
before automatically opening the
power rear gate, the operation will be
canceled.
– Moving your hand or arm away
from the rear emblem before the
electronic chirp starts to sound.
– Not moving your hand or arm
away from the rear emblem even
after the electronic chirp starts to
sound.
– Touching the rear emblem
.
The rear gate may suddenly open
under the following circumstances if
someone is holding the access key fob
near the vehicle.
– Washing the vehicle by hand and/
or machine.
– There is an object rearward of the
vehicle in a narrow space.
– Attaching a carrier on the back-
side of the vehicle
– Attaching a trailer
– Removing snow
Take the access key fob out of the
operation range or turn off the function
when you do not want to activate the
Hands-free Power Rear Gate function.
Refer to “Hands-free Power Rear Gate
off switch”
.
The Hands-free Power Rear Gate
function may not operate properly in
the following conditions.
– In heavy rain
– The rear gate is very dirty.
– The vehicle is covering by snow.
– Hands and arms may not be
detected because of clothing.
– The system of the vehicle cannot
detect the access key fob.
In those cases, push the rear gate
opener button to open.
.
Touching the rear emblem or holding
your hand over the rear emblem during
automatic opening does not stop the
automatic opening.
!
Hands-free Power Rear Gate off
switch
Rear Gate (Outback/Subaru Outback Wilderness)
162
(165,1)
Hands-free Power Rear Gate off switch
status
1)
Inactive
2)
Active
Pressing the Hands-free Power Rear Gate
off switch deactivates the Hands-free
Power Rear Gate function.
2-11. Moonroof (If Equipped)
WARNING
Never let anyone’s hands, arms,
head or any objects protrude from
the moonroof. A person could be
seriously injured if the vehicle stops
suddenly or turns sharply or if the
vehicle is involved in an accident.
To avoid serious personal injury
caused by entrapment, you must
conform to the following instruc-
tions without exception.
.
Before closing the moonroof,
make sure that no one’s hands,
arms, head or other objects will
be accidentally caught in the
moonroof.
.
Before leaving the vehicle, al-
ways remove the key from the
ignition switch for safety (models
without “keyless access with
push-button start system”) and
never allow an unattended child
to remain in the vehicle. Failure to
follow this procedure could re-
sult in injury to a child operating
the moonroof.
.
Never try to check the anti-en-
trapment function by deliberately
placing part of your body in the
moonroof.
CAUTION
.
Do not sit on the edge of the open
moonroof.
.
Do not operate the moonroof if
falling snow or extremely cold
conditions have caused it to
freeze shut.
.
The anti-entrapment function
does not operate when the moon-
roof is being tilted down. Be sure
to confirm that it is safe to do so
before tilting the moonroof down.
.
If the moonroof does not close,
have the system checked by a
SUBARU dealer.
The moonroof has both tilting and sliding
functions.
The moonroof operates only when the
ignition switch is in the “ON” position.
– CONTINUED –
Moonroof
163
2
Keys
and
Doors
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст