Subaru Outback (2022 year). Manual in english — page 13
(199,1)
Inside warning
chime
Outside warning
chime
Operation indica-
tor on push-button
ignition switch
Status
Action
Ding
—
—
The battery of the access key fob is low.
Replace the battery of the access key fob.
Ding
—
Flashes in green
(15 seconds max.)
Steering lock warning:
The engine start procedure is performed, but
the steering is still locked.
While turning the steering wheel right and left
lightly, depress the brake pedal and press the
push-button ignition switch.
Ding
—
Flashes in orange
System malfunction warning:
A malfunction is detected in the power
system or steering lock.
Contact a SUBARU dealer immediately and
have the vehicle inspected.
– CONTINUED –
Warning and Indicator Lights
197
3
Instruments
and
Controls
(200,1)
&
Security Indicator Light
This indicator light shows the status of the
alarm system. It also indicates operation of
the immobilizer system.
!
Alarm system
It blinks to show the driver the operational
status of the alarm system. For detailed
information, refer to “Alarm System”
!
Immobilizer system
The security indicator light starts blinking
in the following conditions.
For models with “keyless access with
push-button start system”:
.
Immediately after the push-button igni-
tion switch is turned to the “OFF” position.
.
Immediately after the driver’s door is
opened or closed when all of the following
conditions are met.
– The push-button ignition switch is in
the “ON” or “ACC” position.
– The engine is not running.
In the event that an unauthorized key is
used (for example, the key is unregistered
or the ID code does not match), the power
is not switched to “ON” and the security
indicator light continues blinking.
For models without “keyless access
with push-button start system”:
.
Approximately 60 seconds after the
ignition switch is turned from the “ON”
position to the “ACC” or “LOCK” position.
.
Immediately after the key is pulled out.
If the indicator light does not blink in the
above conditions, it may indicate that
immobilizer system may be malfunction-
ing. Contact your nearest SUBARU dealer
immediately.
In the event that an unauthorized key (for
example, an unauthorized duplicate) is
used, the security indicator light illumi-
nates. For details about the immobilizer
system, refer to “Immobilizer”
NOTE
.
The security indicator light remains
off in the following conditions. It means
that the matching of the ID code is
completed and the immobilizer system
is deactivated, and it does not indicate
a malfunction.
Models with “keyless access with
push-button start system”:
– While the engine is running
– The push-button ignition switch
has been turned to the “ON” or
“ACC” position and the driver’s
door has not been opened or closed
Models without “keyless access
with push-button start system”:
– While the engine is running
– For approximately 60 seconds
after the ignition switch is turned
from the “ON” position to the “ACC”
or “LOCK” position
– When the ignition switch is in the
“ON” position
.
Even if a malfunction occurs, such
as the security indicator light flashes
irregularly, it will not affect the func-
tionality of the immobilizer system.
Warning and Indicator Lights
198
(201,1)
&
SI-DRIVE Indicator Light (If
Equipped)
SI-DRIVE indicator light
1)
Intelligent (I) mode
2)
Sport Sharp (S#) mode
This light indicates the current SI-DRIVE
mode.
For details of SI-DRIVE mode, refer to
“SI-DRIVE”
&
Select Lever/Gear Position
Indicator
1)
Upshift indicator
2)
Downshift indicator
3)
Select lever/gear position indicator
The select lever position is displayed on
the indicator.
!
Upshift/downshift indicator
When the manual mode is selected, the
gear position indicator (which shows the
current gear selection) and the available
upshift/downshift indicator light up. Refer
to “Selection of Manual Mode”
&
Turn Signal Indicator
Lights
These lights show the operation of the turn
signal or lane change signal.
If the indicator lights do not blink or blink
rapidly, the turn signal bulb may be burned
out. Replace the bulb as soon as possible.
Refer to “Replacing Bulbs”
&
High Beam Indicator
Light
This light shows that the headlights are in
the high beam mode.
This indicator light also illuminates when
operating the headlight flasher.
&
High Beam Assist Indi-
cator
This indicator appears when the high
beam assist function is activated. For
details about the high beam assist func-
tion, refer to “High Beam Assist Function”
– CONTINUED –
Warning and Indicator Lights
199
3
Instruments
and
Controls
(202,1)
&
Automatic Headlight
Beam Leveler Warning
Light
This light illuminates when the automatic
headlight beam leveler does not operate
normally.
If this light illuminates while driving or does
not turn off approximately 3 seconds after
turning the ignition switch to the “ON”
position, have your vehicle inspected at
your SUBARU dealer.
&
LED Headlight Warning
Light
This light illuminates if the LED headlights
malfunction. Have your vehicle inspected
at a SUBARU dealer as soon as possible.
&
Steering Responsive
Headlight OFF Indicator
Light
This light illuminates when the Steering
Responsive Headlight function is off. For
details about the on/off setting, refer to
“Car settings”
&
Steering Responsive
Headlight Warning
Light
The light flashes when a malfunction
occurs in the Steering Responsive Head-
light. Refer to “Steering Responsive Head-
light (SRH)”
&
Headlight Indicator
Light
This indicator light illuminates under the
following conditions.
.
The light switch is turned to the “
” or
“
” position.
.
The light switch is in the “AUTO”
position and the headlights illuminate
automatically.
&
Front Fog Light Indica-
tor Light (If Equipped)
This indicator light illuminates while the
front fog lights are illuminated.
&
Auto Start Stop Warn-
ing Light (Yellow)
CAUTION
If the Auto Start Stop warning light is
illuminated in yellow, there may be a
malfunction in the Auto Start Stop
system. When starting the engine
again after the Auto Start Stop
warning light illuminates, if it is still
illuminating, have your vehicle in-
spected at a SUBARU dealer as soon
as possible.
The Auto Start Stop warning light will
illuminate in yellow if you open the engine
hood when the engine has been tempora-
rily stopped by the Auto Start Stop system.
In this case, to ensure safety, the engine
will not be automatically restarted, even if
you release the brake pedal. Use normal
operation to restart the engine.
&
Auto Start Stop OFF
Indicator Light
This light will illuminate when “Auto Start
Stop” is touched to prevent the Auto Start
Stop system from operating. It will turn off
when “Auto Start Stop” is touched once
more to enable operation of the Auto Start
Stop system. For details about the setting,
refer to “Auto Start Stop ON/OFF icon”
P216 (11.6-inch display models) or
(dual 7.0-inch display models).
Warning and Indicator Lights
200
(203,1)
CAUTION
If the Auto Start Stop OFF indicator
light does not illuminate when “Auto
Start Stop” is touched, contact a
SUBARU dealer for an inspection as
soon as possible.
&
Auto Start Stop Indica-
tor Light (Green)
This indicator light illuminates when the
engine has been temporarily stopped by
the Auto Start Stop system. It will turn off
when the engine is restarted.
&
Auto Start Stop No
Activity Detected Indi-
cator Light
When a vehicle is stopped, the indicator
light illuminates when the operating con-
ditions of idling stop are not met. The light
will turn off when the vehicle starts driving.
Refer to “Non-operational conditions”
&
X-MODE Indicator (Outback/
Subaru Outback Wilderness)
X-MODE indicator (models with 1 mode)
1)
X-MODE indicator
X-MODE indicator (models with 2 modes)
1)
DEEP SNOW/MUD mode indicator
2)
SNOW/DIRT mode indicator
This indicator appears while X-MODE is
activated. It will disappear when X-MODE
is deactivated. Refer to “To Activate/
Deactivate X-MODE”
&
Hill Descent Control
Indicator (Outback/
Subaru Outback
Wilderness)
This indicator appears while the hill des-
cent control function is in standby. It will
flash while the hill descent control function
is operating. It will disappear when the hill
descent control function is not available.
– CONTINUED –
Warning and Indicator Lights
201
3
Instruments
and
Controls
(204,1)
&
BSD/RCTA Warning In-
dicator (If Equipped)
This warning indicator appears on the
combination meter display (color LCD)
when the BSD (Blind Spot Detection) or
RCTA (Rear Cross Traffic Alert) is mal-
functioning for any reason. For further
details, refer to “BSD/RCTA Warning In-
dicator”
P394. If this indicator remains
displayed, have your vehicle inspected by
your SUBARU dealer as soon as possible.
&
BSD/RCTA OFF Indica-
tor (If Equipped)
This indicator appears on the combination
meter display (color LCD) when “BSD/
RCTA” is touched to deactivate the BSD
(Blind Spot Detection) and RCTA (Rear
Cross Traffic Alert), or when the BSD/
RCTA is suspended temporarily. For de-
tails, refer to “BSD/RCTA OFF Indicator”
&
Icy Road Surface
Warning Indicator
When the outside temperature is 37
8
F
(3
8
C) or less, the icy road surface warning
indicator will illuminate to inform the driver
that the road surface may be frozen.
NOTE
.
The outside temperature indicator
shows the temperature in the area
around the sensor. However, the tem-
perature may not be indicated correctly
or the update may be delayed in the
following conditions.
– While parking or driving at low
speeds
– When the outside temperature
changes suddenly (example: when
going in and out of an underground
parking area or when passing
through a tunnel)
– When starting the engine after
being parked for a certain period of
time
.
The icy road surface warning indi-
cator should be treated only as a guide.
Be sure to check the condition of the
road surface before driving.
.
Once the icy road surface warning
indicator appears, it will not disappear
unless the outside temperature has
increased to 41
8
F (5
8
C) or higher.
&
RAB Warning Indi-
cator (If Equipped)
This indicator illuminates if the Reverse
Automatic Braking (RAB) system malfunc-
tions. Refer to “Reverse Automatic Brak-
&
RAB OFF Indicator (If
Equipped)
This indicator illuminates when the Re-
verse Automatic Braking (RAB) system is
turned OFF, or when the Reverse Auto-
matic Braking (RAB) system is suspended
temporarily. Refer to “Reverse Automatic
Braking (RAB) System”
&
Driver Monitoring Sys-
tem Operation Indicator
Light (Green) (If
Equipped)
This indicator illuminates when the Driver
Monitoring System is activated. Refer to
“Driver Monitoring System operation in-
dicator light (green)”
&
Driver Monitoring Sys-
tem Warning Light (Yel-
low) (If Equipped)
This warning light illuminates if the Driver
Monitoring System malfunctions. Have
your vehicle inspected at a SUBARU
dealer as soon as possible. Refer to
“Driver Monitoring System operation in-
dicator light (green)”
Warning and Indicator Lights
202
(205,1)
&
Driver Monitoring Sys-
tem OFF Indicator Light
(If Equipped)
This indicator illuminates when “Driver
Monitoring System” is touched to deacti-
vate Driver Monitoring System. Refer to
“Driver Monitoring System OFF indicator
light”
&
Driver Monitoring Sys-
tem Temporary Stop In-
dicator Light (If
Equipped)
This indicator illuminates when the Driver
Monitoring System is temporarily stopped.
Refer to “Driver Monitoring System tem-
porary stop indicator light”
NOTE
The Driver Monitoring System stops
temporarily in the following circum-
stances.
.
The temperature of the Driver Mon-
itoring System unit is high.
&
Sonar Audible Alarm
OFF Indicator (If
Equipped)
This indicator illuminates when the sonar
audible alarm is turned OFF. For the
setting procedure, refer to “Car settings”
3-7. Combination Meter Dis-
play (Color LCD)
WARNING
Always pay adequate attention to
safe driving when operating the
combination meter display (color
LCD) while the vehicle is in motion.
When operation of the combination
meter display (color LCD) interferes
with your ability to concentrate on
driving, stop the vehicle before
performing operations on the
screen. Also, do not concentrate on
the display while driving. Doing so
may cause you to look away from the
road and could result in an accident.
Various information will be shown on the
combination meter display (color LCD).
Also, a warning message will appear on
the display if a malfunction is detected. In
addition, several settings for the displayed
content can be performed.
– CONTINUED –
Combination Meter Display (Color LCD)
203
3
Instruments
and
Controls
(206,1)
Combination meter display (color LCD)
1)
Meter information screen (Refer to “Me-
ter Information Screen”
2)
Warning screen (Refer to “Warning
Screen”
P205.)/Basic screen (Refer to
3)
EyeSight screen*
4)
Digital speed screen (Refer to “Digital
Speed Screen”
5)
Telltale screen (Refer to “Telltale Screen”
6)
Select lever/gear position indicator (Re-
fer to “Select Lever/Gear Position Indi-
cator”
7)
X-MODE indicator (Outback/Subaru
Outback Wilderness) (Refer to
“X-MODE Indicator (Outback/Subaru
Outback Wilderness)”
SI-DRIVE indicator (if equipped) (Refer
to “SI-DRIVE Indicator Light”
8)
O d o m e t e r ( R e f e r t o “ O d o m e t e r ”
P175.)/Double trip meter (Refer to
*: For details, refer to the separate EyeSight
Owner’s Manual.
&
Basic Operation
Control switches
1)
2)
3)
By operating
or
of the control
switches, the screens can be changed.
If there are some useful messages, such
as vehicle information, warning informa-
tion, etc., they will interrupt the current
screen, and appear on the display accom-
panied by a beep. If such a screen is
displayed, take proper action according to
the message shown on the screen.
The warning screen will return to the
original screen after a few seconds. While
the
information reminder is shown on
the display, it may be possible to display
Combination Meter Display (Color LCD)
204
(207,1)
the warning screen again. To recall the
message marked with
on the display,
pull the
switch on the steering wheel
toward you.
&
Welcome Screen (Opening
Animation) and Good-Bye
(Ending Animation) Screen
Welcome screen and Good-bye screen
are motion graphic displayed on the
combination meter display and center
information display upon entering and
exiting the vehicle.
When the driver’s door is opened and
closed after unlocking the door, the wel-
come screen (opening animation) will
appear on the combination meter display
(color LCD) for approximately 20 seconds.
When the ignition switch is turned to the
“LOCK”/“OFF” position, the combination
meter display (color LCD) gradually turns
off by showing good-bye screen (ending
animation).
NOTE
.
The welcome screen and the good-
bye screen may differ in the actual
words and appearance.
.
The basic screen will be shown
when the ignition switch is turned to
the “ON” position while the welcome
screen is displayed.
.
Once the welcome screen appears, it
takes a certain period of time to display
it again.
.
If the ignition switch is operated
after unlocking the driver’s door, the
welcome screen will not appear even
when the driver’s door is opened and
closed.
.
The welcome screen will disappear
when you lock the driver’s door by
using the remote keyless entry system
(all models) or the keyless access
function (if equipped) while the wel-
come screen is displayed.
.
The welcome screen including the
audio/navigation unit can be set to on
or off.
.
The welcome screen can be set to on
or off. For details, refer to “General
settings”
P219 (11.6-inch display
models) or “General settings”
(dual 7.0-inch display models).
.
The good-bye screen can be set to
on or off. For details, refer to “General
settings”
P219 (11.6-inch display
models) or “General settings”
(dual 7.0-inch display models).
&
Warning Screen
Example of warning
If there is a warning message or a
maintenance notification, it will appear on
combination meter display (color LCD).
Take the appropriate actions based on the
messages indicated.
&
Meter Information Screen
The meter information screen can be
changed. For details, refer to “General
settings”
P219 (11.6-inch display mod-
els) or “General settings”
P237 (dual
7.0-inch display models).
– CONTINUED –
Combination Meter Display (Color LCD)
205
3
Instruments
and
Controls
(208,1)
!
ECO gauge
The ECO gauge shows the difference
between the average rate of fuel con-
sumption since the trip meter was last
reset and the current rate of fuel consump-
tion.
The ECO gauge indicates the current fuel
efficiency as shown in the following chart.
Displayed unit
Needle position
“+” side
“−” side
MPG
Better
Poorer
l/100km
Poorer
Better
NOTE
.
The ECO gauge shows only an
approximate indication.
.
After resetting the trip meter, the
average rate of fuel consumption is not
shown until driving 0.6 miles (1 km).
Until that time, the ECO gauge does not
operate.
!
Clock and temperature
This screen displays the clock and outside
temperature.
For details about clock setting, refer to
“Clock”
!
Compass (if equipped)
The direction of the vehicle is displayed.
!
Driving range on remaining fuel
Combination Meter Display (Color LCD)
206
(209,1)
NOTE
The driving range on the remaining fuel
is only a guide. The indicated value may
differ from the actual driving range on
the remaining fuel, so you must im-
mediately fill the tank when the low fuel
warning light illuminates.
&
Telltale Screen
1)
Telltale screen
When the corresponding situation occurs,
the following telltales will be displayed on
the telltale screen.
NOTE
.
When there is warning information
to display, it will be displayed in five
warning indicators, starting on the left
in ascending order of severity.
.
If there are 6 or more warning
messages to display, the indicators will
be displayed in sequential order.
Mark
Name
Page
Door open indicator
light
Engine hood open
warning light
AT OIL TEMP warning
light
All-Wheel Drive warn-
ing light
LED headlight warning
light
High beam assist indi-
cator light
Steering Responsive
Headlight OFF indicator
light
Steering Responsive
Headlight warning light
Engine low oil level
warning indicator
RAB warning light (if
equipped)
Mark
Name
Page
RAB OFF indicator (if
equipped)
BSD/RCTA warning in-
dicator (if equipped)
BSD/RCTA OFF indi-
cator (if equipped)
Auto Start Stop warning
light (yellow)
Auto Start Stop OFF
indicator light
Auto Start Stop indica-
tor light (green)
Auto Start Stop No Ac-
tivity Detected indicator
light
Automatic headlight
beam leveler warning
light
Windshield washer fluid
warning light
Hill descent control in-
dicator light (Outback/
Subaru Outback
Wilderness)
– CONTINUED –
Combination Meter Display (Color LCD)
207
3
Instruments
and
Controls
(210,1)
Mark
Name
Page
Driver Monitoring Sys-
tem operation indicator
light (green) (if
equipped)
Driver Monitoring Sys-
tem warning light (yel-
low) (if equipped)
Driver Monitoring Sys-
tem OFF indicator light
(if equipped)
Driver Monitoring Sys-
tem temporary stop in-
dicator light (if
equipped)
Icy road surface warn-
ing light
&
Basic Screens
By operating the
or
switch on the
steering wheel, you can change the screen
that is always displayed.
Average fuel consumption screen:
AVG: Average fuel consumption
: Driving range on remaining fuel
This screen displays the average rate of
fuel consumption since the trip meter was
last reset.
NOTE
The driving range on the remaining fuel
is only a guide. The indicated value may
differ from the actual driving range on
the remaining fuel, so you must im-
mediately fill the tank when the low fuel
warning light illuminates.
Current fuel consumption screen:
: Current fuel consumption
: Driving range on remaining fuel
NOTE
The driving range on the remaining fuel
is only a guide. The indicated value may
differ from the actual driving range on
the remaining fuel, so you must im-
mediately fill the tank when the low fuel
warning light illuminates.
Combination Meter Display (Color LCD)
208
(211,1)
Driving information screen:
: Journey time
: Journey distance
This screen displays the journey time (the
time that has elapsed since the ignition
switch was turned to the “ON” position)
and journey distance (the distance that
has been driven since the ignition switch
was turned to the “ON” position).
Auto Start Stop screen:
: The total amount of time that the engine
was stopped by means of the Auto Start
Stop system
: The total amount of fuel saved due to the
engine being stopped by the Auto Start
Stop system
The indicated values are calculated from
the most recent reset of the currently
displayed trip meter to the current time.
The indication ranges are as follows.
.
Total amount of time: from 00
’
00
@
to
9999h59
’
59
@
.
Total amount of fuel saved: from 0 gal to
9999.999 gal
NOTE
.
When the trip meter is reset, the
corresponding accumulated time and
the amount of fuel saving are also reset.
.
The time spent with the engine
stopped by means of the Auto Start
Stop system is also added to the
journey time.
TPMS screen (U.S.-spec. models):
This screen displays each tire pressure.
When a tire is deflated, the deflated tire
and the tire pressure will be displayed on
the screen in yellow.
NOTE
.
The tire pressure values are dis-
played several minutes after driving.
.
You can set the tire pressure units.
For details about setting the units, refer
to “General settings”
P219 (11.6-inch
display models) or “General settings”
P237 (dual 7.0-inch display models).
– CONTINUED –
Combination Meter Display (Color LCD)
209
3
Instruments
and
Controls
(212,1)
.
Once the tire pressure monitoring
system detects the low tire pressure,
the tire pressure values will display in
yellow until the system detects the
normal tire pressure.
.
Immediately adjust the tire pressure
when the warning light illuminates.
When the tire pressure monitoring
system detects the adjusted tire pres-
sure, the warning light will turn off and
the tire pressure values will turn to
white.
.
For information about the specified
value of the air pressure, refer to
“Tires”
Compass screen (if equipped):
The direction of the vehicle is displayed.
Navigation screen (if equipped):
When the route guidance is set in the
navigation system, this item shows the
navigation route information. For details
about the navigation system, refer to the
separate navigation/audio Owner’s Man-
ual.
Audio screen:
The audio screen shows the status of
audio information. For details about the
audio system, refer to the separate navi-
gation/audio Owner’s Manual.
Combination Meter Display (Color LCD)
210
(213,1)
Clock and outside temperature screen:
This screen displays the clock and outside
temperature.
For details about clock setting, refer to
“Clock”
&
Digital Speed Screen
1)
Speed limit indicator (if equipped)
2)
Vehicle speed
This screen displays the current vehicle
speed.
3-8. Center Information Dis-
play (CID)
WARNING
Always pay attention to safe driving
when operating the center informa-
tion display while the vehicle is in
motion. When operation of the cen-
ter information display is disturbing
your awareness and ability to con-
centrate on driving, stop the vehicle
in a safe place before performing
operations on the display. Also, do
not concentrate on the display while
driving. Doing so could result in an
accident.
&
Features
All information is displayed on the center
information display, including vehicle set-
tings, vehicle status, navigation system (if
equipped) operation, audio operation, and
air conditioning operation.
– CONTINUED –
Center Information Display (CID)
211
3
Instruments
and
Controls
(214,1)
Items
Page for
11.6-inch
display
models
Page for
dual 7.0-
inch display
models
Interruption
screen
Vehicle status and
maintenance in-
formation
Vehicle settings
Climate control
operations
Front View Moni-
tor (if equipped)/
Rear view camera
Navigation system
Refer to the navigation/
audio Owner’s Manual.
Audio/telephone
Refer to the navigation/
audio Owner’s Manual.
EyeSight
Refer to the Owner’s
Manual supplement for
the EyeSight system.
The center information display can also be
used to set and initialize the center
information display itself.
NOTE
.
When the vehicle is in motion,
certain functions and selections may
not be available.
.
The language and units for both the
center information display and the
combination meter display (color LCD)
can be changed. For details about
language settings, refer to “General
settings”
P219 (11.6- inch display
models) or “General settings”
(dual 7.0-inch display models). For de-
tails about unit settings, refer to “Car
settings”
P223 (11.6-inch display
models) or “Vehicle setting icons”
P242 (dual 7.0-inch display models).
.
The images displayed in this Own-
er’s Manual are sample images. The
actual image may vary depending on
the region and vehicle specifications.
&
Welcome Screen
Welcome screen and Good-bye screen
are motion graphic displayed on the
combination meter display and center
information display upon entering and
exiting the vehicle.
When the driver’s door is opened and
closed, the welcome screen will appear for
a short time.
NOTE
.
The welcome screen will disappear
when the ignition switch is turned to the
“ON” position while the welcome
screen is shown.
.
The welcome screen can be turned
on or off. For details, refer to “General
P219 (11.6-inch display
models) or “General settings”
(dual 7.0-inch display models).
.
For a certain period of time after the
welcome screen has once appeared, it
may not appear again even when the
driver’s door is opened and closed.
This does not indicate a malfunction.
&
Good-Bye Screen
The good-bye screen will be displayed
under the following conditions.
.
The driver’s door is opened after the
ignition switch is put in the “OFF” position.
.
3 minutes have passed after the ignition
switch is put in the “OFF” position with the
driver’s door closed.
.
10 minutes have passed when the
hands-free phone is used after the ignition
switch is put in the “OFF” position.
.
The battery voltage is low when the
ignition switch is put in the “OFF” position.
&
Interruption Screen
Useful messages, such as reminders,
weather information (if equipped) and
traffic information (if equipped) may inter-
rupt the current screen and appear on the
display accompanied by a beep. Take the
proper action according to the message.
Center Information Display (CID)
212
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст