Subaru BRZ (2012 year). Manual — part 16

PI-11

Pre-delivery Inspection

PRE-DELIVERY INSPECTION

NOTE:

• The hazard lights flash twice and the buzzer

sounds twice when unlocking.

• The hazard lights flash once and the buzzer

sounds once when locking.

• While carrying the access key, check that the

trunk unlocks when you press the trunk opener but-

ton.

• Close all doors, and while carrying the access

key, check that all doors are locked automatically

30 seconds after grasping the front door knob

(touching the touch sensor) to unlock doors.

• Check the mechanical key attached to the ac-

cess key can be used for locking/unlocking.

• With the access key in the vehicle, check that

warning buzzer sounds and locking does not occur

when you touch the door touch sensor.
CAUTION:

Remove the mechanical key from the access

key and hold the mechanical key.

• With the front door locked and the access key in

the trunk (with trunk closed), check that the warning

buzzer sounds and the trunk unlocks when you

press the trunk opener button.

22.SECURITY SYSTEM

• Model with keyless access function
Check that the security system operates as indicat-

ed below.

1) Turn on the security system.

2) Fully open all the door windows.

3) Remove the key from ignition switch, and then

close all doors.

4) Press the access key “LOCK” button once.

5) When all doors are locked, the security indicator

light illuminates to indicate that the alarm system is

in the monitoring prepared condition.

6) The security indicator light flashes once for two

seconds 30 seconds after the condition of step 5) is

reached, and the system enters the monitoring

condition.

(A) Lock-touch sensor

(A) Trunk opener button

(A) Mechanical key

PI-00785

(A)

PI-00771

(A)

PI-00786

(A)

(1) Security indicator light

PI-00813

PI-00773

(1)

PI-12

Pre-delivery Inspection

PRE-DELIVERY INSPECTION

7) Press the access key “UNLOCK” button once.

8) The driver’s door unlocks and the alarm system

is in the non-monitoring condition.

9) Check that the alarm does not sound when any

of the doors are opened.

10) Press the access key “LOCK” button once with

one door open.

11) Check that the buzzer sounds to warn that the

door is not fully closed.

12) Close all doors.

13) Illuminates to indicate monitoring prepared

condition (indicator light illuminates).

14) The security indicator light flashes once for two

seconds 30 seconds after the condition of step 13)

is reached, and the system enters the monitoring

condition.

15) Press the “UNLOCK” button on the access key

once to turn the system into non-monitoring condi-

tion.

16) Momentarily press the “LOCK” button of the

power door lock switch with any one door open.

• Driver’s side

• Passenger’s side

17) Close all doors.

18) When all doors are locked, the indicator light il-

luminates to indicate that the alarm system is in the

monitoring prepared condition.

19) The security indicator light flashes once for two

seconds 30 seconds after the condition of step 18)

is reached, and the system enters the monitoring

condition.

20) When the alarm system is in the monitoring

condition, use the inner lock knob or the key to un-

lock the door.

21) Check that the alarm condition occurs (horn

sounds continuously, hazard light flashes, security

indicator illuminates).

22) Check that the condition described in 21) con-

tinues for 60 seconds or more, or until the access

key “UNLOCK” button is pressed, or until the posi-

tion switch is turned ON with the correct access

key.

23) When none of above is applicable, perform

troubleshooting for the security system.

24) Turn off the security system.

PI-00814

PI-00813

PI-00814

PI-00776

PI-00779

PI-13

Pre-delivery Inspection

PRE-DELIVERY INSPECTION

23.SEAT

1) Check that each seat provides full functionality in

sliding and reclining. Check all available functions

of the rear seat such as the backrest tilt knob.

2) Check the passenger’s seat occupant detection

system.

(1) Empty the passenger’s seat and turn the ig-

nition switch to ON.

(2) Check that the passenger airbag ON/OFF

indicator lights both turn on simultaneously for

approximately six seconds, and after turning off

for two seconds, only the OFF light illuminates.

3) Have an adult passenger sit in the passenger’s

seat, and check whether the ON light of the pas-

senger side airbag ON/OFF indicator illuminates.

4) Have the passenger get out of the passenger’s

seat, and check whether the OFF light of the pas-

senger side airbag ON/OFF indicator illuminates.

24.SEAT BELT

1) Pull out the seat belt and then release it. Check

that the belt retracts smoothly.

2) Check seat belt warning function

(1) Turn the ignition switch to ON with the driv-

er’s and passenger’s seat belt detached.

(2) Check the driver’s and passenger’s seat belt

warning light blink for approx. 6 seconds and

the buzzer sounds intermittently.

(3) Afterwards, check that the seat belt warning

lights illuminate. (If no passenger is on the pas-

senger’s seat, the seat belt warning light on

passenger’s seat does not operate.)

25.TPMS (U.S. MODEL)

1) Turn the ignition switch to ON, and check that

the TPMS warning light is in a normal operation

condition.

• Normal operation (IG ON (Light check))

2) If the TPMS warning light display does not oper-

ate normally, check and repair the system.

26.GROMMET INSTALLATION

Install the grommet contained in the glove box to

the tie-down hole.
CAUTION:

Securely install the grommet to ensure that the

tie-down hole is blocked up by the grommet.

Dust or foul odors could pass into the side seal

through the tie-down hole and enter the interior

directly from the rear quarter.

27.HORN

Check if the horn sounds.

28.HAZARD LIGHT

Check that the hazard lights illuminate.

29.MAP LIGHT

After installing the fuse, check that the map light il-

luminates/turns off normally.

PI-00787

(1) Grommet

2s

IGN ON

ON

OFF

PI-00376

(1)

PI-00801

PI-14

Pre-delivery Inspection

PRE-DELIVERY INSPECTION

30.DELIVERY MODE CONNECTOR

Connect the delivery mode connector of the driv-

er's side A pillar lower area. After connection,

check that the key interlock system functions.

31.IMMOBILIZER SYSTEM

1) Check that the engine starts with all keys that are

equipped on vehicle. Also, when starting the en-

gine, check that the security indicator light goes off.

2) Check that the security indicator light flashes im-

mediately after removing the key. (model without

keyless access function)

3) Check that the security indicator light flashes im-

mediately after turning the ignition switch from ON

to ACC or OFF, or when the doors are opened/

closed with the ignition switch at ON or ACC. (mod-

el with keyless access function)
NOTE:

If malfunctions occur, refer to “IMMOBILIZER (DI-

AGNOSIS)”.

32.STARTING CONDITION

Start the engine and check that the engine starts

smoothly. If the battery voltage is low, recharge or

replace the battery. If any noises are observed, im-

mediately stop the engine and check and repair the

abnormal components.

33.EXHAUST

Listen to the exhaust noise to see if no noises are

observed. Check that no leaks are found.

34.INDICATOR AND WARNING LIGHTS

Check that all indicator lights and warning lights are

operating correctly.

35.HEATER & VENTILATION

Operate the heater & ventilation system to check

for normal airflow outlet control, air inlet control, air-

flow capacity and heating performance.

36.AIR CONDITIONER

Operate the air conditioner. Check that the A/C

compressor operates normally and enough cooling

is provided.

NOTE:

To prevent the insufficient lubrication of the air con-

ditioner, operate the air conditioner for five minutes

at idling.

37.CLOCK

Check that the clock operates normally.

38.AUDIO

1) Check if the AM/FM radio broadcasting can be

heard.

2) Check that all the radio functions work properly

and the noise level is normal.

3) Check the CD and AUX for normal operation.

4) Check that the AUX is installed into the console

without looseness.

39.NAVIGATION SYSTEM

1) Check all display functions for normal operation.

(Refer to the operation manual.)

2) Check that the navigation system operates nor-

mally.

3) Check the radio, CD player and AUX for normal

operation.

4) Check that the AUX is installed into the console

without looseness.

40.ACCESSORY POWER SUPPLY SOCKET

1) Check operation of the accessory power supply

socket in console box.

2) Check operation of the accessory power supply

socket in the glove box.

41.LIGHTING

1) Check the headlight operations. When pulling

out the key, check if the headlight illuminates by

turning the headlight switch from OFF to ON.

2) Check the stop light operation.

3) Check other lights for normal operations.

42.VSC

• With the engine running, operate the VSC

SPORT switch, and check that the “VSC SPORT”

and “VSC OFF” indicator lights illuminate and that

they turn off when the switch is operated again.

• With the engine running, press the VSC OFF

switch for a short period (approx. 1 sec. or less),

and check that the “TRC OFF” indicator light illumi-

nates and that it turns off when the switch is oper-

ated again.

• With the engine running, press the VSC OFF

switch for a long period (approx. 3 sec. or more),

and check that the “TRC OFF” and “VSC OFF” in-

dicator lights illuminate and that they turn off when

the switch is pressed again for a short period.

(A) Delivery mode connector

(A)

PI-00795