Jaguar X-Type Sedan and Estate (Wagon). Manual — part 467
5. NOTE: Federal market vehicles only.
Remove the fuel level sender and harness.
Installation
• W ARNINGS:
Do not smoke or carry lighted tobacco or an open flame of any type when working on or near any fuel related components. Highly
flammable vapors are always present and may ignite. Failure to follow these instructions may result in personal injury.
Do not carry or operate cellular phones when working on or near any fuel related components. Highly flammable vapors are always
present and may ignite. Failure to follow these instructions may result in personal injury.
This procedure involves fuel handling. Be prepared for fuel spillage at all times and always observe fuel handling precautions. Failure
to follow these instructions may result in personal injury.
1. To install, reverse the removal procedure.
Published: 11-May-2011
Fuel Tank and Lines - Fuel Level Sender RH2.5L NA V6 - AJV6/3.0L NA V6 - AJ27
Removal and Installation
Removal
• W ARNINGS:
Do not smoke or carry lighted tobacco or an open flame of any type when working on or near any fuel related components. Highly
flammable vapors are always present and may ignite. Failure to follow these instructions may result in personal injury.
Do not carry or operate cellular phones when working on or near any fuel related components. Highly flammable vapors are always
present and may ignite. Failure to follow these instructions may result in personal injury.
This procedure involves fuel handling. Be prepared for fuel spillage at all times and always observe fuel handling precautions. Failure
to follow these instructions may result in personal injury.
1. Remove the fuel pump module.
For additional information, refer to:
Fuel Pump Module - 2.5L NA V6 -
AJV6/3.0L NA V6 - AJ27
(310-01 Fuel Tank and Lines, Removal and
Installation).
2. Disconnect the fuel level sender electrical connector.
3. Remove the fuel level sender.
Installation
• W ARNINGS:
Do not smoke or carry lighted tobacco or an open flame of any type when working on or near any fuel related components. Highly
flammable vapors are always present and may ignite. Failure to follow these instructions may result in personal injury.
Do not carry or operate cellular phones when working on or near any fuel related components. Highly flammable vapors are always
present and may ignite. Failure to follow these instructions may result in personal injury.
This procedure involves fuel handling. Be prepared for fuel spillage at all times and always observe fuel handling precautions. Failure
to follow these instructions may result in personal injury.
1. To install, reverse the removal procedure.
Published: 11-May-2011
Fuel Tank and Lines - Fuel Level Sensor2.0L Duratorq-TDCi/2.2L Duratorq-TDCi
(110kW/150PS) - Puma
Removal and Installation
Special Tool(s)
Remove/Install fuel pump/transfer pump locking
ring
310-127
Removal
• W ARNINGS:
Do not smoke or carry lighted tobacco or an open flame of any type when working on or near any fuel related components. Highly
flammable vapors are always present and may ignite. Failure to follow these instructions may result in personal injury.
Do not carry or operate cellular phones when working on or near any fuel related components. Highly flammable vapors are always
present and may ignite. Failure to follow these instructions may result in personal injury.
This procedure involves fuel handling. Be prepared for fuel spillage at all times and always observe fuel handling precautions. Failure
to follow these instructions may result in personal injury.
1. Remove the fuel tank.
For additional information, refer to:
Fuel Tank - 2.0L Duratorq-TDCi/2.2L
Duratorq-TDCi (110kW /150PS) - Puma
(310-01 Fuel Tank and Lines,
Removal and Installation).
2. Disconnect the fuel lines.
For additional information, refer to:
Quick Release Coupling - Push
Connect
(310-00 Fuel System - General Information, General
Procedures).
3. NOTE: Note the orientation of the fuel level sensor before removal.
Using the special tool, remove the locking ring.
4. Detach the top of the fuel level sensor.
5.
CAUTION: Make sure the float or arm are not damaged while
removing the fuel level sensor.
Remove the fuel level sensor.
1. Rotate the lower part of the fuel level sensor.
2. Remove the fuel level sensor.
Remove and discard the seal.
Installation
1. WARNINGS:
Do not smoke or carry lighted tobacco or an open flame of any type
when working on or near any fuel related components. Highly flammable
vapors are always present and may ignite. Failure to follow these
instructions may result in personal injury.
Do not carry or operate cellular phones when working on or near any
fuel related components. Highly flammable vapors are always present and
may ignite. Failure to follow these instructions may result in personal
injury.
This procedure involves fuel handling. Be prepared for fuel spillage
at all times and always observe fuel handling precautions. Failure to follow
these instructions may result in personal injury.
CAUTION: Make sure the float or arm are not damaged while
installing the fuel level sensor.
• NOTE: Install a new seal.
• NOTE: Make sure the fuel level sensor is correctly orientated.
To install, reverse the removal procedure.
Tighten to 85 Nm.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст