Jaguar X-Type Sedan and Estate (Wagon). Manual — part 690

3. Tighten to 9 Nm.

Published: 11-May-2011

Supplemental Restraint System - Side Impact Sensor

Removal and Installation

Removal

1. WARNINGS:

To avoid accidental deployment and possible personal injury, the

backup power supply must be depleted before repairing or replacing any air
bag supplemental restraints system (SRS) components. To deplete the
backup power supply energy, disconnect the battery ground cable and wait
one minute. Failure to follow this instruction may result in personal injury.

Never probe the electrical connectors of air bag modules or any

other SRS component. Failure to follow this instruction may result in
personal injury.

• NOTE: Repair is made by replacement only. If a part is replaced and the
new part does not correct the condition, install the original part and carry
out the diagnostic procedure again.

Disconnect the battery ground cable. For additional information, refer to
Section

414-01 Battery, Mounting and Cables

.

2. Position the seat fully forwards.

3. Remove the B-pillar lower trim panel. For additional information, refer

to Section

501-05 Interior Trim and Ornamentation

.

4. NOTE: Left-hand shown, right-hand similar.

Disconnect the side impact sensor electrical connector.

5. NOTE: Left-hand shown, right-hand similar.

Remove the side impact sensor.

Installation

1. WARNINGS:

To avoid accidental deployment and possible personal injury, the

backup power supply must be depleted before repairing or replacing any air
bag supplemental restraints system (SRS) components. To deplete the
backup power supply energy, disconnect the battery ground cable and wait
one minute. Failure to follow this instruction may result in personal injury.

Make sure the side impact sensor locating tangs are correctly

located into the B-pillar. Failure to follow this instruction may result in
personal injury.

Never probe the electrical connectors of air bag modules or any

other SRS component. Failure to follow this instruction may result in
personal injury.

To install, reverse the removal procedure.

Tighten to 12 Nm.

Published: 11-May-2011

Uni-Body, Subframe and Mounting System -

Lubricants, Fluids, Sealers and Adhesives

Specification

Bush installation lubrication

Shell gravex oil 973

Torque Specifications

Description

Nm

lb-ft

lb-in

Front subframe front mount retaining bolts

142

105

-

Front subframe rear mount retaining bolts

142

105

-

Front subframe reinforcement plate retaining bolts

35

26

-

Front stabilizer bar link arm retaining nuts

47

35

-

Steering gear heat shield retaining bolts

7

-

62

Steering gear to subframe retaining bolts

133

98

-

Steering gear cooling pipe retaining bolts

7

-

62

Engine roll restrictor retaining bolts

80

59

-

Front lower arm ball joint retaining nuts

83

61

-

Rear subframe mounting retaining bolts

126

93

-

Rear shock absorber to wheel knuckle retaining bolts

130

96

-

W heel knuckle mounting bracket to body retaining bolts

126

93

-

Rear brake caliper retaining bolts

32

24

-

Published: 11-May-2011

Uni-Body, Subframe and Mounting System - Frame Assembly

Description and Operation

FRONT SUB-FRAME ASSEMBLY

The front sub-frame is bolted to the body and aids in structural support. The front sub-frame provides the mounting surface for the steering
gear, the front suspension lower arm, the stabilizer bar and the engine roll restrictor support bracket.

On vehicles from 2009MY using the 2.2 Diesel engine and the AW F21 6 speed transmission, a dynamic damper is fitted to the front
sub-frame. The damper improves refinement in the 1500-1800 rpm range of the engine. The damper is attached to the rear

LH (left-hand)

corner of the sub-frame. An integral stud on the damper is located through a hole in the sub-frame and secured with a flanged nut.

REAR SUB-FRAME ASSEMBLY

The rear sub-frame is bolted to the body and aids in structural support. The rear sub-frame provides the mounting surface for the rear
suspension components, the exhaust hanger insulator and the rear drive differential.