Jaguar X-Type Sedan and Estate (Wagon). Manual — part 425
23. Attach the gearshift cables to the transaxle.
24. NOTE: Remove the transaxle plug.
Using the special tool, install a new right-hand halfshaft seal.
25. Install a new right-hand halfshaft snap ring.
26.
CAUTION: Make sure the halfshaft constant velocity (CV) joints
do not over articulate. Failure to follow this instruction may result in
damage to the CV joints.
Detach the right-hand halfshaft.
27. Detach the power steering fluid pipe.
28. CAUTIONS:
Make sure the halfshaft CV joints do not over articulate. Failure to
follow this instruction may result in damage to the CV joints.
Make sure the halfshaft seal is not damaged. Failure to follow this
instruction may result in an transaxle fluid leak.
Attach the right-hand halfshaft to the transaxle.
Make sure the halfshaft snap ring is correctly seated.
29. NOTE: Remove the transaxle plug.
Using the special tool, install a new left-hand halfshaft seal.
30.
CAUTION: Make sure the halfshaft CV joints do not over
articulate. Failure to follow this instruction may result in damage to the CV
joints.
Attach the left-hand halfshaft.
Engage the left-hand halfshaft to the transaxle.
Tighten to 25 Nm.
31. Attach the coolant pipe to the engine.
Tighten to 40 Nm.
32. Install the vacuum solenoids and vacuum reservoir mount bracket
assembly.
Tighten to 23 Nm.
33. Attach the wiring harness to the vacuum solenoids and vacuum
reservoir mount bracket.
34. Connect the vacuum solenoid valves electrical connectors.
35. Connect the vacuum pipes to the vacuum solenoid valves and the
vacuum reservoir.
36. Install the front subframe.
For additional information, refer to:
Front Subframe - 2.0L Duratorq-
TDCi/2.2L Duratorq-TDCi (110kW /150PS) - Puma
(502-00 Uni-Body,
Subframe and Mounting System, Removal and Installation).
37. NOTE: Left-hand shown, right-hand similar.
Tighten the shock absorber and spring assembly securing nuts.
Tighten to 25 Nm.
38. Install the air cleaner.
For additional information, refer to:
Air Cleaner
(303-12B Intake Air
Distribution and Filtering - 2.0L Duratorq-TDCi/2.2L Duratorq-TDCi
(110kW/150PS) - Puma, Removal and Installation).
39. Install the battery tray.
For additional information, refer to:
Battery Tray
(414-01 Battery,
Mounting and Cables, Removal and Installation).
40. Fill the manual transaxle to the correct oil level.
For additional information, refer to:
Transaxle Draining and Filling -
Vehicles W ith: 6-Speed Manual Transaxle - MMT6
(308-03 Manual
Transmission/Transaxle, General Procedures).
Published: 11-May-2011
Manual Transmission/Transaxle - Transaxle2.2L Duratorq-TDCi (110kW/150PS) -
Puma
Installation
Special Tool(s)
Halfshaft oil seal installer
205-115
Powertrain assembly jack
HTJ1200-2
Engine support bracket
303-021
Installation
1. Using the special tool, install the transaxle.
Using the special tool raise the transaxle assembly.
Align the transaxle to the clutch plate.
2. NOTE: Shown with the special tool removed for clarity.
Install the transaxle retaining bolts.
Tighten to 48 Nm.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст