Jaguar XJ (X350). Manual — part 1125
2. Rear electronic control module (REM) connector, CR04
Circuit
Pin
Critical fuel level switch - signal 13
3. Rear electronic control module (REM) connector, CR11
Circuit
Pin
Critical fuel level switch - signal return 23
4. Key off. 5. Disconnect the fuel pump module connector, FP13. 6. Measure the resistance between:
FP13, component side FP13, component side
Pin 05
Pin 06
Is the resistance between 425 and 440 ohms?
-> Yes
GO to Pinpoint Test G552807t25.
-> No
INSTALL a new fuel pump module.
Fuel Pump Module - 2.7L V6 - TdV6 (19.45.08) Report the findings in an electronic product quality
report (EPQR).
G552807t25 : CHECK THE CRITICAL FUEL LEVEL SWITCH RESISTANCE
(EMPTY)
1. Remove and drain the fuel pump module. 2. Measure the resistance between:
FP13, component side FP13, component side
Pin 05
Pin 06
Is the resistance between 100 and 105 ohms?
-> Yes
GO to Pinpoint Test G552807t4.
-> No
INSTALL a new fuel pump module.
Fuel Pump Module - 2.7L V6 - TdV6 (19.45.08) Report the findings in an electronic product quality
report (EPQR).
G552807t4 : CHECK THE CRITICAL FUEL LEVEL SWITCH SIGNAL CIRCUIT
FOR SHORT CIRCUIT TO GROUND
1. Measure the resistance between:
FP13, harness side
Battery
Pin 06
Negative terminal
Is the resistance greater than 100 Kohms?
-> Yes
GO to Pinpoint Test G552807t5.
-> No
REPAIR the short circuit. For additional information, refer to the wiring diagrams. Clear any DTCs, test
the system for normal operation.
G552807t5 : CHECK THE CRITICAL FUEL LEVEL SWITCH SIGNAL CIRCUIT
FOR SHORT CIRCUIT TO POWER
1. Measure the resistance between:
FP13, harness side
Battery
Pin 06
Positive terminal
Is the resistance greater than 100 Kohms?
-> Yes
GO to Pinpoint Test G552807t45.
-> No
www.
REPAIR the short circuit. For additional information, refer to the wiring diagrams. Clear any DTCs, test
the system for normal operation.
G552807t45 : CHECK THE CRITICAL FUEL LEVEL SWITCH SIGNAL RETURN
CIRCUIT FOR SHORT CIRCUIT TO POWER
1. Measure the resistance between:
FP13, harness side
Battery
Pin 05
Positive terminal
Is the resistance greater than 100 Kohms?
-> Yes
GO to Pinpoint Test G552807t1.
-> No
REPAIR the short circuit. For additional information, refer to the wiring diagrams. Clear any DTCs, test
the system for normal operation.
G552807t1 : CHECK THE CRITICAL FUEL LEVEL SWITCH SIGNAL CIRCUIT
FOR HIGH RESISTANCE
1. Disconnect the REM electrical connector, CR04. 2. Measure the resistance between:
FP13, harness side CR04, harness side
Pin 06
Pin 13
Is the resistance less than 10 ohms?
-> Yes
GO to Pinpoint Test G552807t47.
-> No
REPAIR the high resistance circuit. For additional information, refer to the wiring diagrams. Clear any
DTCs, test the system for normal operation.
G552807t47 : CHECK THE CRITICAL FUEL LEVEL SWITCH SIGNAL RETURN
CIRCUIT FOR HIGH RESISTANCE
1. Disconnect the REM electrical connector, CR11. 2. Measure the resistance between:
FP13, harness side CR11, harness side
Pin 05
Pin 23
Is the resistance less than 10 ohms?
-> Yes
Check the fuel pump module relay, GO to Pinpoint Test G552807p4.
-> No
REPAIR the high resistance circuit. For additional information, refer to the wiring diagrams. Clear any
DTCs, test the system for normal operation.
PINPOINT TEST G552807p3 : RIGHT
HAND FUEL LEVEL SENDER
G552807t6 : CHECK THE RIGHT HAND FUEL LEVEL SENDER SIGNAL CIRCUIT
FOR SHORT CIRCUIT TO GROUND
1. Fuel pump module connector, FP13
Circuit
Pin
Fuel level sender - signal
02
Fuel level sender - signal return 01
2. Rear electronic control module (REM) connector, CR04
Circuit
Pin
Fuel level sender - signal 15
3. Rear electronic control module (REM) connector, CR11
Circuit
Pin
Fuel level sender - signal return 23
www.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст