Jaguar XJ (X350). Manual — part 1288
Diagnosis and testing
Audio System
Principles of Operation
For a detailed description of the Audio system, refer to the relevant Description and Operation
sections in the workshop manual.
Audio System
Audio System - VIN Range: H18680->H99999
Audio System
Antenna
Speakers
Speakers
Inspection and Verification
1 . Verify the customer concern.
2 . Visually inspect for obvious signs of mechanical or electrical damage.
Visual Inspection Chart
Electrical
•
Fuses/Relays
•
Damaged, Loose or Corroded Connector(s)
•
Damage to Wiring Loom/Incorrect Location, Stretched or Taught
1 . If an obvious cause for an observed or reported concern is found, correct the cause (if possible)
before proceeding to the next step.
2 . If the cause is not visually evident, check for Diagnostic Trouble Codes (DTCs) and refer to the DTC
Index.
DTC Index
Gateway module
CAUTION: When probing connectors to take measurements in the course of the pinpoint
tests, use the adaptor kit, part number 3548-1358-00
If the control module/component is suspect and the vehicle remains under manufacturer
warranty, refer to the Warranty Policy and Procedures manual (section B1.2), or determine if
any prior approval program is in operation, prior to the installation of a new
module/component.
NOTE:
When performing voltage or resistance tests, always use a digital multi meter (DMM) accurate
to three decimal places and with a current calibration certificate. When testing resistance,
always take the resistance of the DMM leads into account.
NOTE:
Check and rectify basic faults before beginning diagnostic routines that involve pinpoint tests.
NOTE:
Inspect connectors for signs of water ingress, and pins for damage and/or corrosion.
NOTE:
If DTCs are recorded and, after performing the pinpoint tests, a fault is not present, an
intermittent concern may be the cause. Always check for loose connections and corroded
terminals.
DTC
Description
Possible Causes
Action
B11A4 DAB L Band Antenna
•
DAB (digital audio
broadcast) L band
antenna circuit to DAB
module - short to power,
ground or open circuit
Refer to electrical circuit diagrams,
notes and check DAB (digital audio
broadcast) L band antenna circuit
for short to power, ground or open
B11A5 DAB Band 3 Antenna
•
DAB (digital audio
broadcast) band 3
antenna circuit to DAB
module - short to power,
ground or open
Refer to electrical circuit diagrams,
notes and check DAB (digital audio
broadcast band 3) antenna circuit
for short to power, ground or open
B1238
Over Temperature
Fault
•
Gateway module - over
temperature
Check gateway module and
location for causes of excessive
NOTE:
www.
temperature, install a new gateway
module as required, refer to the
new module installation note at the
top of the DTC Index
B1342
ECU Internal failure
•
Gateway module -
internal failure
Internal failure, install a new
gateway module as required, refer
to the new module installation
note at the top of the DTC Index
B1A89 Satellite Antenna
•
Satellite radio module or
digital tuner antenna
circuit - short to power,
ground or open
Refer to electrical circuit diagrams,
notes and check satellite radio
module or digital tuner antenna
circuit for short to power, ground
or open
B2477
Module Configuration
Failure
•
Gateway module -
configuration failure
The module can be configured
using the new module procedure.
Check and configure as required
U0193
Lost Communication
with Digital Audio
Control
Module(SDARS)
•
Gateway module - lost
communication with
satellite radio module
Refer to electrical circuit diagrams,
notes and check gateway module
to satellite radio module power
and bus circuit to gateway module
on MOST ring
U0194
Lost Communication
with Digital Audio
Control Module
•
Gateway module - lost
communication with
digital audio broadcast
module
Refer to electrical circuit diagrams,
notes and check gateway module
to digital audio broadcast module
power and bus circuit to gateway
module on MOST ring
U0237
Lost Communication
with Digital Audio
Control Module
•
Gateway module - lost
communication with
(DACMC) Digital Audio
Control Module C
Refer to electrical circuit diagrams,
notes and check gateway module
to Digital Audio Control Module C
power and bus circuit to gateway
module on MOST ring
U1A15
Incomplete MOST
Ring Reported By
Gateway Module
•
Gateway module -
(MOST) ring break
Refer to electrical circuit diagrams,
notes and check (MOST) circuit for
ring break
U2601
(D2B)Wake-up Line
Short To Ground
•
Gateway module, wake-
up line circuit - short to
Refer to electrical circuit diagrams,
notes and check gateway module
(D2B) wake-up line circuit for short
ground
to ground
U2609
(D2B)Wake-up
Pulsewidth Out Of
Specification
•
Gateway module - wake-
up line circuit fault
(pulse< 50mS, pulse >
110mS)
Refer to electrical circuit diagrams,
notes and check gateway module
(D2B) wake-up line circuit for fault
U2610
(D2B) Slave ECU Fails
To Receive A Report
Position
•
Gateway module - during
initialization no position
status report is received
from one or more slave
modules
Refer to electrical circuit diagrams,
notes and check (D2B) slave
modules and circuit for fault,
replace as required, refer to the
new module installation note at the
top of the DTC Index
U2611
(D2B) Slave ECU fails
to receive an alarm
clear command
•
Gateway module - on
entering alarm state,
slave ECU has failed to
receive alarm clear
command
Refer to electrical circuit diagrams,
notes and check (D2B) slave
modules and circuit for fault,
replace as required, refer to the
new module installation note at the
top of the DTC Index
U3004 Digital Tuner State
•
Gateway module, digital
tuner MOST slave -
module is inoperative
Suspect digital tuner module
replace as required, refer to the
new module installation note at the
top of the DTC Index
U3098 Over Temperature
•
Gateway module, digital
tuner (Most slave) -
above temperature
threshold
Check digital tuner module and
location for causes of excessive
temperature, install a new module
as required, refer to the new
module installation note at the top
of the DTC Index
Audio Amplifier Module
CAUTION: When probing connectors to take measurements in the course of the pinpoint
tests, use the adaptor kit, part number 3548-1358-00
NOTE:
If the control module/component is suspect and the vehicle remains under manufacturer
warranty, refer to the Warranty Policy and Procedures manual (section B1.2), or determine if
any prior approval program is in operation, prior to the installation of a new
www.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст