Jaguar XJ (X350). Manual — part 751
TP sensors
ECT sensor
MAF sensor
Transmission malfunction
Traction control event
Air leakage
Breather system
disconnected/restricted
G45704->G99999 For transmission
information,
For intake system,
Intake Air Distribution and Filtering -
VIN Range: G45704->G99999 For
breather system information,
Engine Emission Control - VIN Range:
G45704->G99999
DTC Index
NOTE:
Generic scan tools may not read the codes listed, or may read only 5-digit codes. Match the 5
digits from the scan tool to the first 5 digits of the 7-digit code listed to identify the fault (the last
2 digits give extra information read by the manufacturer-approved diagnostic system).
NOTE:
For a full list of DTCs,
Electronic Engine Controls - VIN Range: G45704->G99999
DTC
Description
Possible causes
Action
P035100
Cylinder 1 ignition coil
primary/secondary
circuit
ECM to ignition module/coil
drive circuit: short circuit to
ground, high resistance
Ignition module/coil ground
circuit: high resistance
Ignition module/coil supply
circuit: open circuit
(including relay)
For ignition coil tests, GO to
Pinpoint Test G531326p1.
P035200
Cylinder 2 ignition coil
primary/secondary
circuit
ECM to ignition module/coil
drive circuit: short circuit to
ground, high resistance
Ignition module/coil ground
For ignition coil tests, GO to
Pinpoint Test G531326p1.
circuit: high resistance
Ignition module/coil supply
circuit: open circuit
(including relay)
P035300
Cylinder 3 ignition coil
primary/secondary
circuit
ECM to ignition module/coil
drive circuit: short circuit to
ground, high resistance
Ignition module/coil ground
circuit: high resistance
Ignition module/coil supply
circuit: open circuit
(including relay)
For ignition coil tests, GO to
Pinpoint Test G531326p1.
P035400
Cylinder 4 ignition coil
primary/secondary
circuit
ECM to ignition module/coil
drive circuit: short circuit to
ground, high resistance
Ignition module/coil ground
circuit: high resistance
Ignition module/coil supply
circuit: open circuit
(including relay)
For ignition coil tests, GO to
Pinpoint Test G531326p1.
P035500
Cylinder 5 ignition coil
primary/secondary
circuit
ECM to ignition module/coil
drive circuit: short circuit to
ground, high resistance
Ignition module/coil ground
circuit: high resistance
Ignition module/coil supply
circuit: open circuit
(including relay)
For ignition coil tests, GO to
Pinpoint Test G531326p1.
P035600
Cylinder 6 ignition coil
primary/secondary
circuit
ECM to ignition module/coil
drive circuit: short circuit to
ground, high resistance
Ignition module/coil ground
circuit: high resistance
Ignition module/coil supply
circuit: open circuit
(including relay)
For ignition coil tests, GO to
Pinpoint Test G531326p1.
P131500 Persistent misfire
Spark plug
failure/fouled/incorrect gap
ECM to ignition coil primary
For spark plug tests, GO to
Pinpoint Test G531326p2.
For ignition coil circuit tests,
GO to Pinpoint Test
www.
circuit fault (cylinder misfire
detected DTC also flagged)
Fuel delivery pressure low
Fuel injector circuit fault(s)
(injector DTCs also flagged)
Ignition coil failure
Cylinder compression low
G531326p1.
Check the fuel pressure,
Fuel Tank and Lines - 4.2L NA
V8 - AJV8/4.2L SC V8 -
AJV8/3.0L NA V6 - AJ27/3.5L
NA V8 - AJV8, VIN Range:
G45704->G99999 For injector
circuit tests,
Fuel Charging and Controls -
VIN Range: G45704->G99999
Check the cylinder
compressions,
Engine - 4.2L NA V8 -
AJV8/4.2L SC V8 - AJV8/3.0L
NA V6 - AJ27/3.5L NA V8 -
AJV8
P136700
Ignition amplifier
group A
Ignition monitoring circuit to
ECM: open circuit, short
circuit to ground, short
circuit to power
Ignition module/coils right hand
bank ground circuit fault
For ignition coil circuit tests,
GO to Pinpoint Test
G531326p1.
P136800
Ignition amplifier
group B
Ignition monitoring circuit to
ECM: open circuit, short
circuit to ground, short
circuit to power
Ignition module/coils left hand
bank ground circuit fault
For ignition coil circuit tests,
GO to Pinpoint Test
G531326p1.
Pinpoint Tests
CAUTION: When probing connectors to take measurements in the course of the pinpoint
tests, use the adaptor kit, part number 3548-1358-00.
NOTE:
When performing electrical voltage or resistance tests, always use a digital multimeter (DMM)
accurate to 3 decimal places, and with an up-to-date calibration certificate. When testing
resistance, always take the resistance of the DMM leads into account.
Check and rectify basic faults before beginning diagnostic routines involving pinpoint tests.
PINPOINT TEST G531326p1 : IGNITION
COIL CIRCUITS
G531326t2 : CHECK THE IGNITION COIL SUPPLY VOLTAGE CIRCUIT
1. Disconnect the relevant ignition coil electrical connector:
Ignition coil connector
Cylinder 1, PI02
Cylinder 2, PI06
Cylinder 3, PI03
Cylinder 4, PI07
Cylinder 5, PI04
Cylinder 6, PI08
2. Key on, engine off. 3. Make sure the ignition relay is energized. 4. Measure the voltage between:
Ignition coil connector, harness side
Battery
Pin 01
Negative terminal
Is the voltage less than 10.5 Volts?
-> Yes
REPAIR the relevant ignition coil supply circuit. This circuit includes fuse 15 of the front power
distribution box and the ignition relay. For additional information, refer to the wiring diagrams.
CLEAR the DTCs and test the system for normal operation.
-> No
GO to Pinpoint Test G531326t4.
NOTE:
www.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст