Jaguar XJ (X350). Manual — part 982

to the warranty policy and

procedure manual if an ECM is

suspect.

P060D00

Internal control module

accelerator pedal position

performance

Pedal value not plausible

Cycle the ignition and allow

power latch. Clear the DTC and

retest. If the DTC resets, refer

to the warranty policy and

procedure manual if an ECM is

suspect.

P061000

Control module vehicle

options error

VID block fault

Configure the module using

the Jaguar approved diagnostic

system.

P061100

Fuel injection pump control

module requesting engine

stop

Internal control module

monitoring
performance

Cycle the ignition and allow

power latch. Clear the DTC and

retest. If the DTC resets, refer

to the warranty policy and

procedure manual if an ECM is

suspect.

P061700 Starter relay circuit high

Starter relay drive circuit:

short circuit to
power

Starter relay failure

For starter relay and circuit

tests, GO to Pinpoint Test

G549822p22.

P061A00

Internal control module

torque performance - signal

plausibility failure

Absolute engine torque

calculation failure

Cycle the ignition and allow

power latch. Clear the DTC and

retest. If the DTC resets, refer

to the warranty policy and

procedure manual if an ECM is

suspect.

P061C00

Internal control module

engine RPM performance

Processor monitoring

speed not plausable

Cycle the ignition and allow

power latch. Clear the DTC and

retest. If the DTC resets, refer

to the warranty policy and

procedure manual if an ECM is

suspect.

P061E00

Internal control module

brake signal performance

Cruise intervention not

plausible

Cycle the ignition and allow

power latch. Clear the DTC and

retest. If the DTC resets, refer

to the warranty policy and

procedure manual if an ECM is

suspect.

P062200

Generator monitor circuit

plausibility

PWM signal failure

For generator monitor circuit

tests,

Charging System - 2.7L V6 -

TdV6

P062500

Generator monitor circuit

low

Generator monitor

circuit: high
resistance

Generator monitor

circuit: short circuit
to ground

For generator monitor circuit

tests,

Charging System - 2.7L V6 -

TdV6

P062600

Generator monitor circuit

high

Generator monitor

circuit: short circuit
to power

For generator monitor circuit

tests,

Charging System - 2.7L V6 -

TdV6

P062700

Fuel pump module relay

control circuit high

Fuel pump module relay

control circuit: short
circuit to power

Fuel pump module relay

failure

For fuel pump module relay

and circuit tests,

Fuel Tank and Lines - 2.7L V6 -

TdV6

P062800

Fuel pump module relay

control circuit low

Fuel pump module relay

control circuit: high
resistance

Fuel pump module relay

control circuit: short
circuit to ground

Fuel pump module relay

failure

For fuel pump module relay

and circuit tests,

Fuel Tank and Lines - 2.7L V6 -

TdV6

P062900

Fuel pump module relay

control circuit/open

Fuel pump module relay

control circuit: high
resistance

Fuel pump module relay

failure

For fuel pump module relay

and circuit tests,

Fuel Tank and Lines - 2.7L V6 -

TdV6

P062B00

Internal control module -

fuel injector control

performance

Internal control module -

fuel injector control
performance

Cycle the ignition and allow

power latch. Clear the DTC and

retest. If the DTC resets, refer

to the warranty policy and

procedure manual if an ECM is

www.

suspect.

P062D00

Fuel injector driver circuit

performance (right hand

bank)

Injector(s) disconnected

Injector circuit(s): high

resistance, short
circuit to ground,
short circuit to
power

Injector failure

ECM failure

For injector circuit tests,

Fuel Charging and Controls

Refer to the warranty policy

and procedure manual if an

ECM is suspect.

P062E00

Fuel injector driver circuit

performance (left hand

bank)

Injector(s) disconnected

Injector circuit(s): high

resistance, short
circuit to ground,
short circuit to
power

Injector failure

ECM failure

For injector circuit tests,

Fuel Charging and Controls

Refer to the warranty policy

and procedure manual if an

ECM is suspect.

P063400

ECM internal temperature

too high

ECM internal

temperature too
high

Cycle the ignition and allow

power latch. Clear the DTC and

retest. If the DTC resets, refer

to the warranty policy and

procedure manual if an ECM is

suspect.

P064200

ECM internal 5 volt sensor

supply circuit A low

ECM power supply

circuit: high
resistance

ECM power supply

circuit: short circuit
to ground

ECM ground circuit: high

resistance

5 Volt supply

ECM relay malfunction

ECM failure

For ECM power supply tests,

GO to Pinpoint Test

G549822p23.

and GO to Pinpoint Test

G549822p20.

For ECM relay tests, GO to

Pinpoint Test G549822p26.

Refer to the circuit diagrams

for the 5 volt sensor supply.

Cycle the ignition and allow

power latch. Clear the DTC and

retest. If the DTC resets, refer

to the warranty policy and

procedure manual if an ECM is

suspect.

P064300

ECM internal 5 volt sensor

supply circuit A high

ECM power supply

circuit: short circuit
to power

ECM ground circuit:

short circuit to
power

5 Volt supply

ECM relay malfunction

ECM failure

For ECM power supply tests,

GO to Pinpoint Test

G549822p23.

and GO to Pinpoint Test

G549822p20.

For ECM relay tests, GO to

Pinpoint Test G549822p26.

Refer to the circuit diagrams

for the 5 volt sensor supply.

Cycle the ignition and allow

power latch. Clear the DTC and

retest. If the DTC resets, refer

to the warranty policy and

procedure manual if an ECM is

suspect.

P065200

ECM internal 5 volt sensor

supply circuit B low

ECM power supply

circuit: high
resistance

ECM power supply

circuit: short circuit
to ground

ECM ground circuit: high

resistance

5 Volt supply

ECM relay malfunction

ECM failure

For ECM power supply tests,

GO to Pinpoint Test

G549822p23.

and GO to Pinpoint Test

G549822p20.

For ECM relay tests, GO to

Pinpoint Test G549822p26.

Refer to the circuit diagrams

for the 5 volt sensor supply.

Cycle the ignition and allow

power latch. Clear the DTC and

retest. If the DTC resets, refer

to the warranty policy and

procedure manual if an ECM is

suspect.

P065300

ECM internal 5 volt sensor

supply circuit B high

ECM power supply

circuit: short circuit
to power

ECM ground circuit:

short circuit to
power

5 Volt supply

ECM relay malfunction

ECM failure

For ECM power supply tests,

GO to Pinpoint Test

G549822p23.

and GO to Pinpoint Test

G549822p20.

For ECM relay tests, GO to

Pinpoint Test G549822p26.

Refer to the circuit diagrams

for the 5 volt sensor supply.

Cycle the ignition and allow

power latch. Clear the DTC and

retest. If the DTC resets, refer

to the warranty policy and

www.