Jaguar XK. Manual — part 22

91

Lighting

R

Refitting the headlamp unit

1. Reconnect the wiring multi-plug

connector.

2. Offer up the unit into position.

3. Ensure that the locating peg is fitted

into the in-board locating hole.

4. To secure the headlamp unit, first

secure the wheel arch screw, then
repeat the removal procedure in the
reverse order, ensuring that the
powerwash pipe is reconnected.

Note: After the replacement of any bulb
and the fitting of the headlamp unit, the
aim of the headlamps should be checked
by a Jaguar Dealer.

Front side marker lamp

1. Remove the headlamp unit.

2. Twist the bulb holder counter

clockwise and pull out the bulb
complete with the bulb holder.

3. Pull the bulb out of the bulb holder.

4. Insert the new bulb (WY5W) and

repeat the above procedure in
reverse order.

3

E91169

2

3

E91170

Lighting

92

L

Front direction indicator lamp

1. Remove the headlamp unit.

2. Twist the bulb holder counter

clockwise and pull out the bulb
complete with the electrical
connector.

3. Twist and pull the bulb out of the bulb

holder.

4. Insert the new bulb (3457AK) and

repeat the above procedure in
reverse order.

Front sidelamp

1. Remove the headlamp unit.

2. Twist and lift off the side domed cap.

3. Pull out the bulb complete with bulb

holder.

4. Pull the bulb out of the bulb holder.

5. Insert the new bulb (W5W) and repeat

the above procedure in the reverse
order. Ensure that the cover is fitted
correctly to retain the water tightness.

E93800

2

3

2

4

E91172

93

Lighting

R

High and low beam projector unit

1. Remove the headlamp unit.

2. Twist and lift off the rear domed cap.

3. Twist the bulb unit counter clockwise

to unlock it. Pull the bulb unit clear of
the headlight unit.

4. Press the electrical connector release

lever and disconnect the bulb unit.

5. Press the bulb unit adaptor ring catch

and remove the adaptor ring from the
bulb unit.

6. Secure the bulb unit adaptor ring onto

the new bulb (D1S35W) and repeat
the above procedure in the reverse
order. Ensure that the cover is fitted
correctly to retain the water tightness.

CAUTION

It is strongly advised that the High
Intensity Discharge (HID) Xenon
low and high beam project unit

(D1S35W) should be replaced by a
Jaguar Dealer.

3

2

4

5

E91173

Lighting

94

L

Cornering or static bending lamp

1. Remove the headlamp unit.

2. Twist and lift off the side domed cap.

3. Twist the bulb holder counter

clockwise to unlock, then pull out the
bulb complete with electrical
connector.

4. To release the bulb unit, lift the two

catches of the electrical connector,
then pull to remove the bulb unit.

5. Insert the new bulb unit (H8) and

repeat the above procedure in the
reverse order. Ensure that the cover is
fitted correctly to retain the water
tightness.

Rear fog, reverse and high level
brake lamps

These lamps are LED units and are
integral to the luggage compartment lid.
They should be replaced by a Jaguar
Dealer.

CAUTION

Halogen bulbs will be damaged if
touched by hand or contaminated
with oil or grease. It is important to

use clean gloves or lint free cloth when
handling a bulb which is to be used
again. A contaminated bulb may be
cleaned with methylated spirit before
refitting.

2

3

4

E91174

WARNING

LED lamp units operate at a high
temperature. If they have recently
been in use, allow sufficient time

for them to cool down before touching
them.