Range Rover BORG WARNER 44-62 TRANSFER BOX. Manual — part 6
TRANSFER BOX
10
OVERHAUL
REDUCTION HUB
Service repair no - 41.20.70/01
Remove
1. Remove viscous coupling assembly.
See this
section.
2. Remove 17 bolts securing halves of transfer
gearbox casing.
3. Carefully break RTV seal and remove front
transfer box casing from rear casing.
4. Remove selector fork assembly, interlock spool
shaft and reduction hub from rear casing.
Collect tube spacer.
5. Remove reduction hub from selector fork.
TRANSFER BOX
OVERHAUL
11
Refit
1. Clean RTV sealant from front and rear casing
mating surfaces.
CAUTION: Do not use a metal scraper as
this may damage sealing surfaces.
2. Fit reduction hub to selector fork with hub
splines towards the shorter end of shift rail.
3. Fit tube spacer to interlock spool shaft.
4. Engage selector fork cam follower to interlock
spool cam track.
5. Fit reduction hub to intermediate shaft and
engage interlock spool shaft and shift rail to
holes in rear casing.
6. Rotate interlock spool shaft to position
reduction hub and selector fork to low ratio
position, nearest rear casing half. Ensure tube
spacer is in position and selector fork cam
follower is correctly engaged to interlock spool.
7. If removed, fit 2 dowels to front casing.
8. Apply a continuous 2 mm bead of RTV sealant
to rear casing mating face. Path to be around
inside of bolt holes.
9. Fit front casing to rear casing, ensure bolt
holes and dowels are aligned before disturbing
RTV sealant.
10. Fit bolts securing front casing to rear casing
and progressively tighten to 35 Nm. (26 lbf.ft)
11. Check freedom of rotation of input shaft and
that rear output shaft rotates.
12. Fit viscous coupling assembly.
See this
section.
TRANSFER BOX
12
OVERHAUL
INTERLOCK SPOOL
Service repair no - 41.20.74/01
Remove
1. Remove viscous coupling assembly.
See this
section.
2. Remove 17 bolts securing halves of transfer
box casing.
3. Carefully break RTV seal and remove front
transfer box casing from rear casing.
4. Remove selector fork assembly, interlock spool
shaft and reduction hub from rear casing.
Collect tube spacer.
5. Collect interlock spool.
TRANSFER BOX
OVERHAUL
13
Refit
1. Clean RTV sealant from front and rear casing
mating surfaces.
CAUTION: Do not use a metal scraper as
this may damage sealing surfaces.
2. Fit tube spacer to interlock spool shaft.
3. Engage selector fork cam follower to interlock
spool cam track.
4. Fit reduction hub to intermediate shaft and
engage interlock spool shaft and shift rail to
holes in rear casing.
5. Rotate interlock spool shaft to position
reduction hub and selector fork to low ratio
position, nearest rear casing half. Ensure tube
spacer is in position and selector fork cam
follower is correctly engaged in interlock spool.
6. If removed, fit 2 dowels into front casing.
7. Apply a continuous 2 mm bead of RTV sealant
to rear casing mating face. Path to be around
inside of bolt holes.
8. Fit front casing to rear casing, ensure bolt
holes and dowels are aligned before disturbing
RTV sealant.
9. Fit bolts securing front casing to rear casing
and progressively tighten to 35 Nm. (26 lbf.ft)
10. Check freedom of rotation of input shaft and
that rear output shaft rotates.
11. Fit viscous coupling assembly.
See this
section.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст