Discovery 2. Manual — part 346

HARNESSES

REPAIRS

86-7-7

Refit

1. With assistance, position harness to air

conditioning ducting and secure with cable ties.

2. Secure harness to sunroof harness with cable

clips.

3. Connect multiplug to RF receiver.
4. Feed harness to LH and RH upper 'E' posts.
5. Feed harness through 'E' post to tail lamp and

rear bumper and secure with grommet.

6. Connect multiplug to fuel flap solenoid and

alarm sounder.

7. Position alarm sounder to rear quarter and

secure with nut to 9 Nm (7 lbf.ft).

8. Position both RH earth header to 'E' post and

tighten nut to 10 Nm (7 lbf.ft).

9. Feed tail door harness through 'E' post and

secure with grommet.

10. Position harness sleeve to outer edge of door

and pull harness through door.

11. Secure harness to tail door with clips.
12. Connect washer tube to rear of wiper arm.
13. Remove tape from draw string and secure to

CHMSL harness.

14. Draw harness through tail door and connect

Lucars to CHMSL.

15. Fit CHMSL cover and secure with screws.
16. Connect multiplug to door lock switch.
17. Connect Lucars to HRW.
18. Connect multiplug to rear wiper motor.
19. Connect multiplug to door latch.
20. Fit plastic sheet to tail door, ensuring it aligns

with witness marks.

21. Fit tail door trim casing.

+

DOORS, REPAIRS, Trim casing - tail

door.

22. Connect Lucar to radio aerial RH amplifier.
23. Secure harness to RH side of body with clips

and retainers.

24. Position both LH earth header to 'E' post and

tighten nut to 10 Nm (7 lbf.ft).

25. Connect multiplugs to both tail/flasher lamps

and secure harness to bumper with clips.

26. Fit both rear tail lamps.

+

LIGHTING, REPAIRS, Lamp - tail.

27. Secure harness to rear LH side of body with 6

cable clips.

28. Connect 2 Lucars to rear air conditioning unit.
29. Fit both luggage compartment trim casings.

+

INTERIOR TRIM COMPONENTS,

REPAIRS, Trim casing - side - loadspace.

30. Feed harness into position for rear interior light.
31. Connect Lucar to radio aerial LH amplifier.
32. Secure harness to body with cable ties clips

and retainers.

33. Secure air conditioning ducting to body with

rivets.

34. Feed harness to LH lower 'A' post.

35. Secure harness to LH side of body with cable

tie clips and retainers.

36. Connect and secure multiplugs to lower LH 'A'

post.

37. Feed harness through roof to centre.
38. Secure harness behind bonnet release cable.
39. Connect rear washer pipe at lower 'A' post and

secure with clip.

40. Secure harness to roof with clips.
41. Connect multiplug to interior mirror, ARC

accelerometer.

42. Position sound deadening panels and secure

with clips.

43. Fit headlining.

+

INTERIOR TRIM COMPONENTS,

REPAIRS, Headlining.

44. Fit fascia panel.

+

INTERIOR TRIM COMPONENTS,

REPAIRS, Fascia.

HARNESSES

86-7-8

REPAIRS

Harness - engine - V8

$% 86.70.17

Remove

1. Remove upper inlet manifold.

+

MANIFOLDS AND EXHAUST

SYSTEMS - V8, REPAIRS, Gasket - inlet
manifold - upper - Without Secondary Air
Injection.

2. Disconnect injector multiplugs, release harness

from fuel rail.

3. Disconnect ignition coil multiplugs.

4. Release and disconnect both HS

2

O sensor

multiplugs.

5. Disconnect CKP sensor multiplug.

HARNESSES

REPAIRS

86-7-9

6. Disconnect air conditioning compressor

multiplug.

7. Remove 2 nuts securing alternator cables and

release cables.

8. Disconnect coolant temperature sensor

multiplug.

9. Release 2 harness clips from coolant rail.

10. Remove nut securing engine harness positive

lead to battery, release lead and position
aside.

HARNESSES

86-7-10 REPAIRS

11. Release clips and remove fuse box cover.
12. Remove bolt securing starter lead to fuse box,

release lead and position aside.

13. Disconnect 2 engine harness multiplugs from

fuse box.

14. Disconnect EVAP solenoid multiplug.

15. Remove nut securing engine harness earth to

body and disconnect engine harness to main
harness multiplug.

16. Remove trim fixings securing toe board and

remove toe board.

17. Disconnect 5 multiplugs connecting engine

harness to ECM.

18. Release engine harness, pull into engine bay.
19. Raise front of vehicle.

WARNING: Do not work on or under a
vehicle supported only by a jack. Always
support the vehicle on safety stands.