Discovery 2. Manual — part 131
TRANSFER BOX - LT230SE
REPAIRS
41-27
19. 03 Model Year onwards - if fitted: Release
and disconnect both differential lock warning
lamp switch multiplugs from main harness.
20. Remove cable tie and multi plug from bracket
on transfer box.
21. Release transfer box breather pipe from
bulkhead clip.
22. Remove 4 bolts from transfer box bottom plate,
position support plate LRT-99-010 to transfer
box and tighten bolts.
23. Position gearbox support jack and secure
support plate to jack using 4 bolts.
24. Remove 3 bolts securing transfer box to
gearbox.
25. Fit 3 guide studs LRT-41-009 through
transfer box bolt holes to support it during
removal.
26. Remove 2 bolts and nut securing transfer box
to gearbox.
CAUTION: If securing stud is removed
during this operation, it must be discarded
and a new stud fitted.
27. Position a jack to support gearbox and engine.
TRANSFER BOX - LT230SE
41-28
REPAIRS
28. Remove 4 bolts and nut, remove gearbox RH
mounting.
29. With assistance, remove transfer box from
gearbox.
30. Remove input shaft oil seal.
REPAIRS, Oil seal - input shaft.
Refit
1. Fit new input shaft oil seal.
REPAIRS, Oil seal - input shaft.
2. Clean transfer box to gearbox mating faces.
3. Raise transfer box on jack and align to guide
studs LRT-41-009.
4. Clean transfer box to gearbox bolt threads.
5. Apply sealant, Part No. STC 50552 to bolt and
stud threads.
6. Fit and lightly tighten 2 bolts and nut securing
transfer box to gearbox. If new stud is to be
fitted, apply sealant, Part No. STC 50552 to
stud threads and tighten to 45 Nm (33 lbf.ft).
7. Remove guide studs, fit and lightly tighten
remaining 3 bolts.
8. Tighten bolts and nut by diagonal selection to
45 Nm (33 lbf.ft).
9. Position gearbox RH mounting and tighten
bolts to 85 Nm (63 lbf.ft).
10. Tighten gearbox RH mounting nut to 48 Nm
(35 lbf.ft).
11. Remove 4 bolts securing support plate to
gearbox jack.
12. Remove 4 bolts securing support plate LRT-99-
010 to transfer box and remove plate.
13. Clean bottom plate bolt threads.
14. Apply sealant, Part No. STC 50552 to threads
of 4 bottom plate bolts.
15. Fit 4 bolts securing bottom plate to transfer box
and tighten to 25 Nm (18 lbf.ft).
16. Position breather pipe and secure to bulkhead
clip.
17. Connect multiplug to reverse light switch.
18. Up to 03 Model Year - if fitted : Connect
Lucars to differential lock switch and multiplugs
to high/low ratio switch and neutral sensor.
19. 03 Model Year onwards - if fitted: Connect
differential lock warning lamp multiplugs,
secure harness.
20. Position high/low ratio selector cable and
secure with clevis pin and 'C' clip.
21. Position differential lock selector cable to
differential lock selector cable abutment
bracket and tighten locknuts sufficiently to
retain cable.
22. If fitted: Fit differential lock selector cable to
transfer gearbox and secure with clevis pin.
23. If fitted: Adjust differential lock selector cable.
ADJUSTMENTS, Cable - selector -
differential lock - adjust.
24. Models fitted with high/low shift interlock
solenoid: Position interlock solenoid harness
to high/low shift cable, fit sleeve around cable
and harness; secure sleeve.
25. Models fitted with high/low shift interlock
solenoid: Connect solenoid multiplug to main
harness and secure multiplug to bracket.
26. Clean handbrake and mating face.
27. Position handbrake back plate and tighten
bolts to 75 Nm (55 lbf.ft).
28. Clean handbrake drum.
29. Fit handbrake drum and tighten retaining
screw.
30. Fit front propeller shaft.
31. Fit rear propeller shaft.
32. Clean exhaust silencer and mating face.
33. Position silencer, fit new gasket , connect
mounting rubbers and tighten nuts to 40 Nm
(30 lbf.ft).
34. Refill transfer box with oil.
35. Fit front exhaust pipe.
TRANSFER BOX - LT230SE
REPAIRS
41-29
Transfer box - V8
$% 41.20.25.99
Remove
1. Remove front exhaust pipe.
SYSTEMS - V8, REPAIRS, Front pipe.
2. Drain transfer box oil.
3. Remove 8 bolts securing rear cross member
and remove cross member.
4. Remove 3 nuts securing intermediate silencer
to tail pipe.
5. Release silencer from mounting rubbers,
remove silencer and discard gasket.
6. Remove front propeller shaft.
7. Remove rear propeller shaft.
8. Remove handbrake drum retaining screw and
remove handbrake drum.
9. Remove 4 bolts from handbrake back plate,
release back plate and tie aside.
10. Models fitted with high/low shift interlock
solenoid: Release interlock solenoid multiplug
and disconnect multiplug from main harness.
11. Models fitted with high/low shift interlock
solenoid: Remove sleeve retaining rings and
remove sleeve from high/low selector cable.
TRANSFER BOX - LT230SE
41-30
REPAIRS
12. If fitted: Release and remove clevis pin
securing differential lock selector cable to
transfer gearbox.
13. If fitted: Loosen locknuts securing differential
lock selector cable to differential lock selector
cable abutment bracket.
14. If fitted: Release and remove differential lock
selector cable from differential lock selector
cable abutment bracket.
15. Remove clevis pin and 'C' clip securing high/
low ratio selector cable to selector lever and
release cable from abutment bracket.
16. Remove 2 cable ties securing cable to fuel
pipes.
17. If fitted: Disconnect 2 Lucars from oil
temperature sensor and disconnect reverse
lamp switch multiplug.
18. Remove banjo bolt securing breather pipe and
discard washers.
19. Up to 03 Model Year - if fitted: Disconnect 2
Lucars from differential lock switch and
multiplugs from high/low ratio switch and
neutral sensor.
20. Disconnect multiplug from reverse light switch.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст