Discovery 2. Manual — part 174

STEERING

REPAIRS

57-31

12. Remove bolt securing PAS pipe bracket to

steering box, release pipes and discard 'O'
rings.

CAUTION: Always fit plugs to open
connections to prevent contamination.

13. Release 5 clips securing hoses to coolant rail

and disconnect hoses.

14. Models with ACE: Remove bolt securing ACE

pipes to chassis to gain access to coolant rail
bolt.

15. Remove bolt securing coolant rail.

16. Release 2 clips securing coolant rails and

remove coolant rail from vehicle.

STEERING

57-32

REPAIRS

17. Remove securing nut and bolt and release

Panhard rod.

18. Remove nut securing drag link to drop arm.

Using LRT-57-036, break taper joint and
release drag link.

19. Models with ACE: Remove nut securing anti-

roll bar link lower ball joint and release joint.

20. With assistance, remove 2 nuts and bolts

securing LH engine mounting to chassis.

STEERING

REPAIRS

57-33

21. With assistance remove 2 nuts and bolts

securing RH engine mounting to chassis.

22. Support the engine weight on a jack.

CAUTION: To prevent damage to
components, cushion the jack pad with a
block of wood or hard rubber.

23. Raise the engine sufficiently to allow the

steering box to clear the sump.

24. Models with ACE: Position ACE control arms

to access steering box bolts.

25. With assistance remove 4 bolts securing

steering box and remove steering box.

26. Remove centralising bolt from steering box.

Refit

1. Fit centralising bolt to steering box.
2. With assistance, position steering box, fit bolts

and tighten to 90 Nm (66 lbf.ft).

3. Lower the engine onto its mountings. Fit engine

mounting bolts and tighten to 85 Nm (63 lbf.ft).

4. Models with ACE: Ensure washer is in place

on lower ball joint of anti-roll bar link, then
connect lower ball joint to axle. Tighten nut to
100 Nm (74 lbf.ft).

5. Position drag link, fit nut and tighten to 80 Nm

(59 lbf.ft).

6. Position Panhard rod, fit bolt and nut and

tighten to 230 Nm (170 lbf.ft).

7. Position coolant rail and secure with clips and

bolt.

8. Fit coolant hoses and secure with clips.
9. Models with ACE: Fit and tighten bolt

securing ACE pipes to chassis.

10. Clean PAS pipe ends and 'O' ring recess.
11. Lubricate new 'O' rings for PAS pipes with clean

PAS fluid.

12. Fit 'O' rings to PAS pipes and position pipes in

steering box. Fit PAS pipe bracket and tighten
bolt to 22 Nm (16 lbf.ft).

13. Ensure steering wheel is centralised. Fit

universal joint between steering box and
intermediate shaft and tighten bolts to 25 Nm
(18 lbf.ft).

14. Remove centralising bolt from steering box.
15. Fit intercooler to turbo hose and secure with

clips.

16. Fit road wheel(s) and tighten nuts to 140 Nm

(103 lbf.ft).

17. Remove stand(s) and lower vehicle.
18. Connect battery earth lead.
19. Fit battery cover.
20. Refill cooling system.

+

COOLING SYSTEM - Td5,

ADJUSTMENTS, Drain and refill.

21. Bleed PAS system.

+

STEERING, ADJUSTMENTS,

Hydraulic system - bleed.

22. Centralise steering linkage

+

STEERING, ADJUSTMENTS,

Steering linkage - centralise.

STEERING

57-34

REPAIRS

Steering box - RHD - diesel

$% 57.10.01

Remove

1. Remove battery cover.
2. Disconnect battery earth lead.
3. Drain cooling system.

+

COOLING SYSTEM - Td5,

ADJUSTMENTS, Drain and refill.

4. Raise front of vehicle.

WARNING: Do not work on or under a
vehicle supported only by a jack. Always
support the vehicle on safety stands.

5. Remove RH front road wheel.
6. Ensure steering wheel is centralised, remove

key from steering lock and engage column lock.

7. Fit centralising bolt to steering box.

8. Remove 3 bolts securing intermediate shaft

and universal joint.

9. Push intermediate shaft upwards, release and

remove universal joint.

CAUTION: Do not turn the steering wheel
with the intermediate shaft or universal joint
disconnected as damage to the rotary
coupler and the steering wheel switches
may occur.

10. Position container below PAS pipes to catch

fluid spillage.