Discovery 2. Manual — part 330
ALARM SYSTEM AND HORN
REPAIR 86-4-25
REPAIR
Switch - central door locking
$% 86.26.30
Remove
1. Carefully remove clock assembly from louvre
panel.
2. Disconnect multiplug from door lock switch.
3. Remove door lock switch from clock.
Refit
1. Fit door lock switch to clock assembly.
2. Connect multiplug to door lock switch.
3. Position clock assembly and push to secure in
position.
Switches - horn
$% 86.30.01
Remove
WARNING: It is imperative that before any
work is undertaken on the SRS system the
appropriate information is read thoroughly.
1. Disconnect both battery leads, negative lead
first, and wait 10 minutes.
2. Remove driver's airbag module.
3. Release horn switch multiplugs and leads from
steering wheel base.
4. Disconnect horn switch multiplugs from
harness.
5. Disconnect horn switch multiplug from rotary
coupler harness.
6. Remove screw securing earth leads to steering
wheel.
7. Using a broad round edged tool, carefully prise
horn switches from steering wheel.
Refit
1. Fit to steering wheel and connect multiplugs.
2. Fit earth leads and secure with screw.
3. Secure leads and multiplugs to base of steering
wheel.
4. Fit driver's airbag module.
ALARM SYSTEM AND HORN
86-4-26 REPAIR
Vehicle horn
$% 86.30.10
Remove
1. Remove front grille.
2. Disconnect multiplug from horn.
3. Remove nut securing horn to body and remove
horn.
Refit
1. Fit horn to body and tighten nut to 13 Nm (10
lbf.ft).
2. Connect multiplug to horn.
3. Fit front grille.
Sounder - alarm
$% 86.77.10
Remove
1. Remove nut securing sounder to mounting
bracket.
2. Release sounder from mounting bracket,
disconnect multiplug and remove sounder.
Refit
1. Position sounder and connect multiplug.
2. Fit sounder to bracket and secure with nut.
ALARM SYSTEM AND HORN
REPAIR 86-4-27
Sounder - battery backed-up (BBUS)
$% 86.77.13
Remove
1. Remove rear quarter lower casing.
REPAIRS, Trim casing - side - loadspace.
2. Remove nut securing BBUS to RH rear body
panel.
3. Disconnect multiplug and remove BBUS.
Refit
1. Position BBUS, connect multiplug and tighten
securing nut.
2. Fit rear quarter lower casing.
REPAIRS, Trim casing - side - loadspace.
Switch - bonnet
$% 86.77.20
Remove
1. Remove rubber cover from bonnet switch.
2. Disconnect multiplug, release switch retainers
and remove switch.
Refit
1. Position switch and connect multiplug.
2. Fit rubber cover to switch,
ALARM SYSTEM AND HORN
86-4-28 REPAIR
Receiver - alarm system - models with
sunroof
$% 86.77.31
Remove
1. Remove trim seal from rear sunroof.
2. Release sunroof switch and remove screw
securing headlining.
3. Remove 2 nuts securing receiver to roof panel,
disconnect multiplug and remove receiver.
Refit
1. Connect multiplug to receiver, fit to roof panel,
tighten nuts to 10 Nm (7 lbf.ft).
2. Fit and tighten screw securing headlining.
3. Fit sunroof switch
4. Fit sunroof trim seal.
5. Connect multiplug to receiver, fit to roof panel
and secure with nuts tighten to 10 Nm (7 lbf.ft).
Receiver - alarm system - models
without sunroof
$% 86.77.31
Remove
1. Remove rear headrest. Repeat operation on
SEATS, REPAIRS, Head restraint -
2. Remove 'D' post trim casing. Repeat operation
REPAIRS, Trim casing - 'D' post.
3. Remove rear interior light.
LIGHTING, REPAIRS, Lamp - interior
4. Release 2 studs securing rear headlining,
carefully lower lining.
5. Remove 2 studs securing alarm receiver.
6. Disconnect multiplug from alarm receiver and
remove receiver.
Refit
1. Connect multiplug to receiver.
2. Position receiver and secure with studs.
3. Position rear end of headlining, secure with
studs.
4. Fit rear interior light.
LIGHTING, REPAIRS, Lamp - interior
5. Fit both 'D' post trim casings. Repeat operation
REPAIRS, Trim casing - 'D' post.
6. Fit rear headrests. Repeat operation on
SEATS, REPAIRS, Head restraint -
M86 5632
M86 5761
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст