Discovery 2. Manual — part 123
MANUAL GEARBOX - R380
OVERHAUL
37-49
5. Remove 2 bolts securing spool retainer to
gearbox case. Remove retainer, remove and
discard 'O' ring - if fitted.
6. Remove interlock spool from selector shaft.
7. Remove filter from gearbox case.
8. Align selector shaft pin with slot in centre plate
and using wooden blocks and hide mallet,
release centre plate and collect lower detent
ball and spring.
9. Press out reverse idler shaft using a suitable
press.
10. Remove idler gear, needle roller bearing and
spacer.
MANUAL GEARBOX - R380
37-50
OVERHAUL
Reassembly
1. Clean centre plate and reverse gear
components.
2. Lubricate gearbox components with clean gear
oil.
3. Position idler gear, bearing and spacer to idler
shaft.
4. Using a suitable press fit idler shaft to centre
plate.
5. Using feeler gauges, check clearance between
reverse idler and shaft flange; fit a thicker or
thinner spacer if necessary in order to achieve
correct clearance:
l
New clearance = 0.04 - 0.38 mm (0.002 -
0.015 in)
l
Service limit = 0.38 mm (0.015 in)
6. Apply sealant, Part No. STC 4404 to gearbox
casing.
7. Fit lower spring and detent ball into centre
plate, retain using a dummy shaft.
8. Align selector shaft pin with slot in centre plate.
9. Fit centre plate and fit 2 off 8x35 mm slave bolts
to retain centre plate in position on gearbox
case; recover dummy shaft.
10. Fit filter to gearbox case.
11. Fit interlock spool to selector shaft.
12. Using new 'O' ring, fit spool retainer and tighten
bolts to 8 Nm (6 lbf.ft).
13. Clean threads of detent plug.
14. Apply sealant, Part No. STC 50552 to threads
of detent plug, fit upper detent ball and spring.
15. Fit detent plug and tighten to 25 Nm (18 lbf.ft).
16. Position reverse gear to layshaft.
17. Position reverse gear complete with bearing,
collar and selective spacer to output shaft.
18. Fit 5th / reverse gear synchroniser.
OVERHAUL, Synchronizer assembly - 5th/
reverse.
Housing - gear selector mechanism
$% 37.16.37.01
Disassembly
1. Remove 4 bolts and remove gear selector
housing.
Reassembly
1. Clean mating faces on selector housing and
gearbox.
2. Apply sealant, STC 4404 to selector housing.
3. Clean selector housing bolt threads.
4. Apply sealant, Part No. STC 50552 to threads
of selector housing bolts, position selector
housing and tighten bolts to 25 Nm (18 lbf.ft)
5. Adjust gear lever bias springs.
MANUAL GEARBOX - R380
OVERHAUL
37-51
Lever - gear change
$% 37.16.04
Disassembly
1. Remove gear selector housing.
OVERHAUL, Housing - gear selector
mechanism.
2. Restrain right hand bias spring using a suitable
pair of grips.
3. Remove 2 bolts securing right hand side of bias
spring adjustment plate.
4. Repeat operations for left hand bias spring.
5. Remove bias springs and adjustment plate.
6. Remove lower gear lever.
7. Remove and discard Railko bush.
8. Remove and discard oil seal from housing.
MANUAL GEARBOX - R380
37-52
OVERHAUL
Reassembly
1. Clean components.
2. Apply multi-purpose grease to ball and cross
pins.
3. Apply multi-purpose to new Railko bush and fit
to housing ensuring that slots are correctly
aligned.
4. Lubricate a new seal with gearbox oil and fit, lip
side towards housing using a suitable mandrel.
5. Position lower gear lever to selector housing
ensuring cross pins are located in Railko bush.
6. Position bias spring adjustment plate to
selector housing.
7. Clean threads of bias spring adjustment plate
bolts and apply sealant, Part No. STC 50552 to
threads.
8. Fit 2 short bolts to secure front of adjustment
plate and tighten to 25 Nm (18 lbf.ft).
9. Position right hand bias spring to pillar ensuring
longest end of spring is against gear lever.
10. Restrain bias spring using a suitable pair of
grips, ensure shortest end of spring is on
outside edge of bolt hole.
11. Fit longest bolt and washer ensuring end of
bias spring is under washer, tighten bolt to 25
Nm (18 lbf.ft).
12. Repeat above procedures for remaining bias
spring.
13. Fit gear selector housing.
OVERHAUL, Housing - gear selector
mechanism.
14. Adjust gear lever bias springs.
ADJUSTMENTS, Spring - gear lever bias.
Housing - clutch
$% 37.12.07
Disassembly
1. Remove clutch release bearing and operating
lever.
2. Remove 6 bolts and remove clutch housing.
Reassembly
1. Clean clutch housing and gearbox mating face.
2. Position clutch housing and tighten bolts to 75
Nm (55 lbf.ft).
3. Fit clutch operating lever and release bearing.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст