Range Rover. Manual — part 166
ZF AUTO
33
REPAIR
SEAL - VALVE BLOCK - SET
Service repair no - 44.20.13
Remove
1. Remove valve body assembly.
See this
section.
2. Remove circlips and springs from gearbox
casing noting location of long and short springs.
3. Remove and discard seals using LRT-44-005
from gearbox casing.
Refit
4. Clean gearbox casing, springs and circlips.
5. Fit new seals using LRT-44-005, ensure seals
are fully seated.
6. Position springs in their correct locations and
secure with circlips.
7. Fit valve body assembly.
See this section.
44
AUTOMATIC GEARBOX
NEW RANGE ROVER
34
REPAIR
PRESSURE REGULATOR
Service repair no - 44.40.22
Remove
1. Remove valve body assembly.
See this
section.
2. Release and remove clip securing pressure
regulator solenoid valve harness to valve body.
3. Disconnect multiplug from pressure regulator
solenoid valve.
4. Remove 5 Torx screws securing pressure
regulator to valve body and remove pressure
regulator.
Refit
5. Clean pressure regulator and mating face with a
lint free cloth.
6. Position pressure regulator to valve body, fit
Torx screws and tighten to
8 Nm (6lbf. ft).
7. Connect multiplug to pressure regulator solenoid
valve, fit clip and secure harness to valve body.
ZF AUTO
35
REPAIR
LOCK-UP SOLENOID VALVE (MV 3)
Service repair no - 44.15.35
Remove
1. Remove valve body assembly.
See this
section.
2. Disconnect multiplug from lock-up solenoid valve
and release harness from clip.
3. Remove Torx screw and retaining fork securing
solenoid valve to valve body.
4. Remove solenoid valve from valve body.
Refit
5. Clean lock-up solenoid valve with lint free cloth.
6. Position solenoid valve in valve body.
7. Position retaining fork, fit and tighten Torx screw
to
8 Nm (6lbf. ft).
8. Connect multiplug to lock-up solenoid valve and
secure harness in clip.
9. Fit valve body assembly.
See this section.
SOLENOIDS - SHIFT CONTROL VALVES (MV 1
and 2)
Service repair no - 44.15.45
Remove
1. Remove valve body assembly.
See this
section.
2. Remove 3 Torx screws securing lock-up
solenoid valve assembly to valve body and
move solenoid aside.
NOTE: This is to gain access to remove
Torx screw and MV2 shift control valve.
3. Note their fitted position and disconnect
multiplugs from shift control valves MV 1 and MV
2.
4. Remove Torx screw and retaining fork securing
MV2 shift control solenoid valve to valve body.
Note that the tag on the retaining fork faces
towards the valve body.
5. Remove shift control valve from valve body.
44
AUTOMATIC GEARBOX
NEW RANGE ROVER
36
REPAIR
Refit
6. Clean MV2 shift control solenoid valve with lint
free cloth.
7. Position MV2 shift control solenoid valve to valve
body.
8. Position retaining fork, fit Torx screw and tighten
to
8 Nm (6lbf. ft).
9. Connect multiplugs to both shift control solenoid
valves.
10. Clean lock-up solenoid valve assembly with a
lint-free cloth.
11. Position lock-up valve assembly, assembly,fit
and tighten Torx screws to
8 Nm (6lbf. ft).
12. Fit valve body assembly.
See this section.
HARNESS - SOLENOID VALVES
Service repair no - 44.15.52
Remove
1. Remove valve body assembly.
See this
section.
2. Release and remove clip securing pressure
regulator solenoid harness to valve body.
3. Disconnect multiplug from pressure regulator
solenoid valve.
4. Disconnect multiplugs from lock-up solenoid
valve, shift control solenoid valves MV 1 and MV
2.
5. Release harness from 5 clips on valve body and
remove harness.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст