Range Rover. Manual — part 109
LAND ROVER V8
37
REPAIR
THROTTLE CABLE - up to 99MY
Service repair no - 19.20.06
Remove
1. Remove split pin and clevis pin securing cable to
throttle linkage.
2. Release cable adjuster from abutment bracket.
3. Release cable from 3 clips along bulkhead and
single clip on brake booster bracket.
4. Remove driver’s side fascia closing panel.
See
CHASSIS AND BODY, Repair.
5. Remove 3 scrivet fasteners securing lower
closing panel.
6. Release panel for access to blower motor
ducting.
19
FUEL SYSTEM
NEW RANGE ROVER
38
REPAIR
7. Release ducting from blower motor housing and
heater. Remove blower motor ducting.
8. Release cable from throttle pedal.
9. Release cable outer from bulkhead location.
Remove throttle cable assembly.
Refit
10. Lubricate bulkhead end of outer cable with liquid
soap to aid fitment.
11. Fully engage cable outer into bulkhead location.
Connect cable to throttle pedal.
12. Position blower ducting. Engage onto heater and
blower motor housing locations.
13. Position lower closing panel. Secure with scrivet
fasteners.
14. Fit driver’s side fascia closing panel.
See
CHASSIS AND BODY, Repair.
15. Route cable along bulkhead. Secure to clips
16. Engage cable adjuster to abutment bracket.
17. Align cable trunnion to throttle linkage. Secure
with clevis pin and split pin.
18. Check and adjust throttle cable free-play.
See
Adjustment.
THROTTLE CABLE - from 99MY
Service repair no - 19.20.06
1. Remove closing panel from fascia.
See
CHASSIS AND BODY, Repair.
2. Remove screw and remove heater outlet duct.
3. Remove 4 scrivets and remove access panel
from fascia.
4. Release and remove heater air duct for access
to throttle pedal lever.
LAND ROVER V8
39
REPAIR
5. Disconnect inner cable from throttle cam.
6. Release cable gaiter.
7. Loosen locknuts and disconnect throttle cable
from abutment bracket.
8. Release throttle cable from 3 clips.
9. Release and disconnect inner cable from throttle
lever.
10. Release throttle cable from bulkhead and
remove from vehicle.
Refit
11. Apply liquid soap to bulkhead end of outer cable.
12. Fit throttle cable to bulkhead, connect and
secure inner cable to pedal lever.
13. Fit throttle cable to abutment bracket and
connect inner cable to throttle cam.
14. Fit throttle cable to clips.
15. Adjust throttle cable.
See Adjustment.
16. Secure gaiter to outer cable.
17. Refit heater air duct.
18. Fit closing panel and secure with scrivets.
19. Fit heater outlet duct and secure with screw.
20. Fit closing panel to fascia.
See CHASSIS AND
BODY, Repair.
19
FUEL SYSTEM
NEW RANGE ROVER
40
REPAIR
FILLER NECK ASSEMBLY - PRE-ADVANCED
EVAPS
Service repair no - 19.55.07
WARNING: If fuel tank is full, fuel level will
be above filler neck aperture in the tank. If
gauge indicates over 75%, drain a
minimum of 10 litres of fuel from tank.
Remove
1. Disconnect battery negative lead.
2. Remove rear wheel arch liner.
See CHASSIS
AND BODY, Repair.
3. Remove fuel filler cap.
4. Slacken clips securing hoses to filler neck.
5. Release fill breather hose from filler neck.
6. Petrol Models Only: Disconnect fuel tank and
charcoal canister hoses from vapour separator.
7. Diesel Models Only: Release cap from quick
release connector. Disconnect breather hose.
8. Remove nut securing filler neck to wheel arch.
9. Release filler neck from fuel tank hose and
grommet in body aperture.
10. Remove filler neck assembly.
Refit
11. Apply liquid soap to grommet and mating surface
of filler neck.
12. Reverse removal procedure.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст