Range Rover. Manual — part 271
SEATS
11
REPAIR
7. Remove cable ties securing harnesses to seat
base and disconnect multiplugs from outstation.
8. Release airbag harness 2 way connector from
bracket.
9. Remove 2 screw covers.
10. Remove 2 screws securing outer side finisher.
11. Release switch harness and remove side
finisher.
12. Remove 2 clips securing squab cover to cushion
frame and release squab cover retainer.
13. Remove 4 Torx screws securing squab
assembly to cushion assembly.
14. Remove cushion assembly from squab
assembly.
15. Remove 10 clips securing cushion cover to
frame.
78
SEATS
NEW RANGE ROVER
12
REPAIR
16. Release 2 retainers securing cover to frame.
17. Remove 2 studs securing cover to frame.
18. Remove cover and foam assembly from frame.
Do not carry out further dismantling if cover
and foam is removed for access only.
19. Remove 15 hog rings securing cover to foam.
Remove cover.
20. Remove retention wires from pockets in cover.
21. Remove side finisher retaining wire from cushion
cover retainer.
Refit
22. Fit side finisher retaining wire and retention wires
to cover.
23. Position cover to foam align retention wires and
fit hog rings.
24. Fit cover and foam assembly to frame.
25. Fit studs securing cover and secure retainers.
26. Fit clips securing cover.
27. Using assistance, position cushion assembly to
squab assembly.
28. Fit Torx screws securing cushion assembly to
squab assembly and tighten to
30 Nm
(22 lbf. ft).
29. Secure squab retainer and fit clips.
30. Position outer side finisher and feed harness
through, locate finisher and fit screws and
covers. Connect multiplugs to outstation.
31. Fit outer side finisher, fit screws and screw
covers.
32. Secure airbag harness connector to bracket.
33. Align harnesses and secure with cable ties.
34. Position seat belt stalk, fit bolt and tighten to
35 Nm (26 lbf.ft).
35. Fit seat.
See this section.
SEATS
13
REPAIR
COVER - SQUAB - FRONT SEAT - from 99MY
Service repair no - 78.90.08/81
Remove
WARNING: The squab cover is
constructed specifically for use on a seat
with a side airbag fitted and must not in
any way be repaired. Covers designed to be used
in conjunction with side airbags can be identified
by an ’AIRBAG’ label sewn into the cover seam
adjacent to the airbag location and an ’AIRBAG
PASS’ label with date of manufacture, sewn inside
the cover.
WARNING: For effective airbag
performance, when fitting the cover,
ensure retention wires, shock cords and
hog rings are correctly located and secure.
1. Remove front seat.
See this section.
2. Remove headrest.
3.
Power headrest: Remove 2 finisher caps.
Manual headrest: Turn retainers through 90
°
and
remove retainers.
4. Remove armrest retaining screw cover.
5. Remove screw securing armrest, collect
anti-rattle washer.
6. Remove armrest and escutcheon.
78
SEATS
NEW RANGE ROVER
14
REPAIR
7. Remove 2 clips and release retainer securing
rear section of cover to frame.
8. Remove 2 clips and release retainer securing
front section of cover to frame.
9. Remove cable ties securing harnesses to
cushion spring. Release heating element
harness and SRS harness 2 way connector.
10.
Seats with memory function: Disconnect
multiplug from seat outstation.
11. Release harness from opening in squab cover.
12. Release shock cords from frame.
13. Raise squab cover.
14. Remove 4 hog rings securing rear of cover for
map pocket.
15. Remove 2 studs securing map pocket strap.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст