Range Rover. Manual — part 70
EMISSION CONTROL
1
REPAIR
CATALYST HEAT SHIELDS
Service repair no - 17.50.05
Remove
1. Remove exhaust front pipe.
See MANIFOLD
AND EXHAUST SYSTEM, Repair.
2. Remove 5 retaining washers securing heat
shield to floor pan studs.
3. Remove heat shield. Discard retaining washers.
Refit
4. Reverse removal procedure.
EVAP CANISTER - PRE-ADVANCED EVAPS
Service repair no - 17.15.13
Remove
1. Disconnect fuel tank vapour and purge valve
hoses from canister.
2. Remove bolt and clamp plate securing canister
to mounting plate.
3. Remove EVAP canister.
Refit
4. Reverse removal procedure.
17
EMISSION CONTROL
NEW RANGE ROVER
2
REPAIR
EVAP CANISTER - ADVANCED EVAPS (up to
99MY)
Service repair no - 17.15.13
Remove
1. Disconnect battery earth lead.
2. Remove 2 screws securing cruise control
actuator bracket to suspension control box.
3. Position cruise control actuator assembly aside.
4. Release clip securing vent solenoid hose to
cannister and disconnect hose.
5. Release vent and purge quickfit connectors from
canister.
6. Remove bolt securing canister to mounting
bracket and collect clamp plate.
7. Remove canister.
Refit
8. Position canister to mounting bracket.
9. Position clamp plate and secure canister to
bracket with bolt.
10. Connect purge and vent hoses to cannister,
ensuring that quickfit connectors correctly
engage.
11. Connect vent solenoid hose to canister and
secure clip.
12. Align cruise control actuator bracket to
suspension control box and secure with screws.
13. Connect battery earth lead.
EMISSION CONTROL
3
REPAIR
EVAP CANISTER - from 99MY
Service repair no - 17.15.13
Remove
1. Release fixings and remove battery cover.
2. Disconnect battery earth lead.
3. Raise vehicle on lift.
4. Release clip and disconnect air hose from
canister.
5. Release and remove purge and tank pipes from
canister.
6. Remove 2 nuts and 2 bolts securing EVAP
canister to chassis.
7. Remove EVAP canister.
8. Remove bolt securing bracket to canister and
remove canister.
CAUTION: Plug the connections.
Refit
9. Fit bracket to canister and secure with bolt.
10. Fit canister to chassis and secure with nuts and
bolts.
11. Ensure all connections are clean.
12. Connect purge and tank pipes to canister.
13. Connect air hose to canister and secure hose
with clip.
14. Lower vehicle.
15. Connect battery earth lead.
16. Fit battery cover and secure with fixings.
17
EMISSION CONTROL
NEW RANGE ROVER
4
REPAIR
EVAP CANISTER - LEVS
Service repair no - 17.15.13
Remove
1. Raise vehicle on 4 post ramp.
2. Remove 3 bolts securing air suspension
reservoir to mounting brackets.
3. Release air suspension reservoir and carefully
move aside.
4. Remove 2 bolts securing EVAP canister
mounting bracket to body.
5. Remove 2 nuts securing EVAP canister
mounting bracket to body.
6. Remove bolt securing EVAP canister to
mounting bracket. Collect nut and mounting
bracket.
7. Remove mounting bracket.
8. Position cloth to absorb any fuel spillage.
9. Release purge and tank vent pipes from EVAP
canister.
10. Remove clip securing CVS valve pipe to EVAP
canister.
11. Release pipe from EVAP canister and remove
canister.
CAUTION: Plug the connections.
Refit
12. Remove plugs and ensure all connections are
clean.
13. Connect CVS valve pipe to EVAP canister and
secure with clip.
14. Connect purge and tank vent pipes to EVAP
canister.
15. Position mounting bracket to EVAP canister and
secure with bolt.
16. Position mounting bracket to body and secure
with nuts.
17. Fit and tighten bolts securing mounting bracket
to body.
18. Lower vehicle.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст