Range Rover. Manual — part 100
LAND ROVER V8
1
REPAIR
AIR CLEANER ASSEMBLY - up to 97MY
Service repair no - 19.10.01
Remove
1. Release 2 clips securing air flow meter to air
cleaner.
2. Release air flow meter. Remove ’O’ ring and
discard.
3. Disconnect intake air temperature sensor.
4. Remove bolt securing air suspension dryer to air
cleaner.
5. Release dryer pipes from 2 clips. Position dryer
aside.
6. Remove 2 bolts securing air cleaner to valance.
7. Release air cleaner lug from valance grommet.
Remove air cleaner.
8. If necessary, remove intake air temperature
sensor.
9. Remove seal.
Refit
10. If removed, refit intake air temperature sensor
with seal to air cleaner. Tighten to
8 Nm (6
lbf.ft)
11. Position air cleaner assembly. Engage lug to
valance grommet. Secure with bolts.
12. Position air suspension dryer to air cleaner.
Secure with bolt. Tighten to
8 Nm (6 lbf.ft)
13. Engage dryer pipes to clips.
14. Connect multiplug to intake air temperature
sensor.
15. Fit new ’O’ ring to air flow meter.
16. Secure air flow meter to air cleaner with clips.
19
FUEL SYSTEM
NEW RANGE ROVER
2
REPAIR
AIR CLEANER ASSEMBLY - from 97MY
Service repair no - 19.10.01
Remove
1. Release 2 clips securing mass air flow (MAF)
meter to air cleaner.
2. Release MAF meter from air cleaner. Remove
and discard ’O’ ring from MAF sensor.
3. Disconnect multiplug from air temperature
sensor.
4. Remove bolt securing air suspension air dryer to
air cleaner.
5. Release air dryer from air cleaner and position
aside.
6. Release air cleaner from 2 valance grommets.
7. Remove air cleaner from inner wing grommet.
Do not carry out further dismantling if
component is removed for access only.
8. Remove air temperature sensor from air cleaner.
9. Remove and discard air temperature sensor
seal.
10. Fit new seal to air cleaner.
11. Fit air temperature sensor to air cleaner and
tighten to
8 Nm (6 lbf.ft)
Refit
12. Fit air cleaner lugs to inner wing and valance
grommets. Ensure lugs are fully engaged to
grommets.
13. Position air dryer to air cleaner, fit bolt and
tighten to
8 Nm (6 lbf.ft)
14. Connect multiplug to air temperature sensor.
15. Fit new ’O’ ring seal to MAF meter.
16. Engage MAF meter to air cleaner and secure
with clips.
LAND ROVER V8
3
REPAIR
ELEMENT - AIR CLEANER - from 99MY
Service repair no - 19.10.10
Remove
1. Release 3 fixings and remove battery cover.
2. Disconnect battery earth lead.
3. Release 2 clips securing air flow meter to air
cleaner assembly.
4. Release air flow meter and position aside.
5. Release 2 clips securing air cleaner top cover
and remove cover.
6. Remove air cleaner element.
Refit
7. Clean inside of air cleaner case and cover.
8. Fit new air cleaner element.
9. Fit air cleaner cover and secure with clips.
10. Connect air flow meter to air cleaner assembly
and secure with clips.
11. Connect battery earth lead.
12. Fit battery cover and secure with fixings.
AIR INTAKE HOSE - up to 99MY
Service repair no - 19.10.17
Remove
1. Loosen 2 clips securing intake hose to plenum
chamber and mass air flow sensor.
2. Release harness from intake hose clip.
3. Release intake hose from plenum chamber.
4. Remove intake hose from mass air flow sensor.
5. Remove 2 clips from intake hose.
Refit
6. Fit clips to intake hose.
7. Fit intake hose to mass air flow sensor.
8. Connect intake hose to plenum chamber.
9. Tighten clips securing intake hose to plenum
and MAF sensor.
10. Engage harness to intake hose clip.
19
FUEL SYSTEM
NEW RANGE ROVER
4
REPAIR
CAMSHAFT POSITION (CMP) SENSOR - up to
99MY
Service repair no - 18.30.24
Remove
1. Disconnect battery negative lead.
2. Release 2 clips securing upper fan cowl.
Remove cowl.
3. Release tension from auxiliary belt. Remove belt
from crankshaft pulley.
4. Release CMP sensor connector from bracket.
Disconnect multiplug.
5. Remove bolt securing CMP sensor to front
cover.
6. Remove CMP sensor.
Refit
7. Ensure mating surfaces are clean.
8. Engage CMP sensor in front cover location.
Secure with bolt. Tighten to
8 Nm (6 lbf.ft)
9. Secure CMP sensor connector to bracket.
Connect multiplug.
10. Turn auxiliary belt tensioner. Refit belt to
crankshaft pulley.
11. Fit upper fan cowl. Secure with clips.
12. Reconnect battery negative lead.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст