Frelander 2. Manual — part 35
General Information - Diagnostic Trouble Code (DTC) IndexDTC: Steering
Angle Sensor Module (SASM)
Description and Operation
• NOTE: If a control module or component is suspect and the vehicle remains under manufacturer warranty, refer to the
Warranty Policy and Procedures manual (section B1.2), or determine if any prior approval program is in operation, before
the replacement of a component.
• NOTE: Generic scan tools may not read the codes listed, or may read only 5-digit codes. Match the 5 digits from the scan
tool to the first 5 digits of the 7-digit code listed to identify the fault (the last 2 digits give extra information read by the
manufacturer-approved diagnostic system).
• NOTE: When performing voltage or resistance tests, always use a digital multimeter (DMM) accurate to three decimal
places, and with an up-to-date calibration certificate. W hen testing resistance always take the resistance of the DMM
leads into account.
• NOTE: Check and rectify basic faults before beginning diagnostic routines involving pinpoint tests.
• NOTE: Inspect connectors for signs of water ingress, and pins for damage and/or corrosion.
• NOTE: If DTCs are recorded and, after performing the pinpoint tests, a fault is not present, an intermittent concern may
be the cause. Always check for loose connections and corroded terminals.
Description And Operation
For a detailed description of the anti lock control stability system, refer to the relevant Description and Operation section
in the workshop manual.
For additional information, refer to:
Anti-Lock Control - Stability Assist
(206-09C Anti-Lock Control - Stability Assist,
Description and Operation).
Steering Angle Sensor Module
DTC
Description
Possible Cause
Action
U0001-00 High Speed CAN
Communication Bus
General Failure
Information No sub type
information
Bus Off
Carry out the pinpoint tests associated to this DTC
using the manufacturer approved diagnostic system
U0140-00 Lost Communication W ith
Central electronic module
General Failure
Information No sub type
information
Lost communication with
CJB
Carry out the pinpoint tests associated to this DTC
using the manufacturer approved diagnostic system
U0300-00 Internal Control Module
Software Incompatibility
General Failure
Information No sub type
information
CAN Bus fault
Loss of power to module
Incorrect component
installed
Module internal failure
Carry out CAN network and power feed tests using
manufacturer approved diagnostic system. Check
correct steering wheel rotation sensor is installed.
Install a new steering wheel rotation sensor as
required, refer to new module/component
installation note at the top of the DTC Index.
U3000-04 Control Module General
Failure Information
System Internal Failures
CAN Bus fault
Loss of power to module
Incorrect component
installed
Module internal failure
Carry out CAN network and power feed tests using
manufacturer approved diagnostic system. Check
correct steering wheel rotation sensor is installed.
Install a new steering wheel rotation sensor as
required, refer to new module/component
installation note at the top of the DTC Index.
U3000-14 Control Module General
Electrical Failures Circuit
short to ground or open
Loss of power to module
Module internal failure
Carry out power feed tests using manufacturer
approved diagnostic system. Install a new steering
wheel rotation sensor as required, refer to new
module/component installation note at the top of
the DTC Index.
U3000-1D Control Module General
Electrical Failures Circuit
current out of range
Loss of power to module
Module internal failure
Carry out power feed tests using manufacturer
approved diagnostic system. Install a new steering
wheel rotation sensor as required, refer to new
module/component installation note at the top of
the DTC Index.
U3000-44 Control Module System
Internal Failures Data
memory failure
Module internal failure
Install a new steering wheel rotation sensor as
required, refer to new module/component
installation note at the top of the DTC Index.
U3000-48 Control Module System
Internal Failures
Supervision software
failure
Module internal failure
Install a new steering wheel rotation sensor as
required, refer to new module/component
installation note at the top of the DTC Index.
U3000-49 Control Module System
Internal Failures Internal
electronic failure
Loss of power to module
Module internal failure
Carry out power feed tests using manufacturer
approved diagnostic system. Install a new steering
wheel rotation sensor as required, refer to new
module/component installation note at the top of
the DTC Index.
U3000-61 Control Module Algorithm
Based Failures Signal
calculation failure
Steering wheel rotation
sensor mis-aligned
Module internal failure
Check for correct installation of sensor. Install a
new steering wheel rotation sensor as required,
refer to new module/component installation note at
the top of the DTC Index.
DTC
Description
Possible Cause
Action
U3000-62 Control Module Algorithm
Based Failures Signal
compare failure
Steering wheel rotation
sensor mis-aligned
Module internal failure
Check for correct installation of sensor. Install a
new steering wheel rotation sensor as required,
refer to new module/component installation note at
the top of the DTC Index.
U3000-64 Control Module Algorithm
Based Failures Signal
plausibility failure
Steering wheel rotation
sensor mis-aligned
Module internal failure
Check for correct installation of sensor. Install a
new steering wheel rotation sensor as required,
refer to new module/component installation note at
the top of the DTC Index.
U3000-81 Control Module Bus Signal
/ Message Failures Invalid
serial data received
Loss of power to module
CAN Bus fault
Module internal failure
Carry out CAN network and power feed tests using
manufacturer approved diagnostic system. Install a
new steering wheel rotation sensor as required,
refer to new module/component installation note at
the top of the DTC Index.
U3000-87 Control Module Bus Signal
/ Message Failures
Missing message
Loss of power to module
CAN Bus fault
Missing module
Carry out CAN network and power feed tests using
manufacturer approved diagnostic system. Check for
missing modules on CAN network
U3000-92 Control Module
Component Failures
Performance or incorrect
operation
Steering wheel rotation
sensor mis-aligned
Module internal failure
Check for correct installation of sensor. Install a
new steering wheel rotation sensor as required,
refer to new module/component installation note at
the top of the DTC Index.
U3003-62 Battery Voltage Algorithm
Based Failures Signal
compare failure
Mis-match in battery
voltage, of 2 volts or
more, between CJB and
steering wheel rotation
sensor module
Carry out the pinpoint tests associated to this DTC
using the manufacturer approved diagnostic system
General Information - Diagnostic Trouble Code (DTC) IndexDTC: Satellite
Digital Audio Radio System Module (SARM)
Description and Operation
• NOTE: If a control module or component is suspect and the vehicle remains under manufacturer warranty, refer to the
Warranty Policy and Procedures manual (section B1.2), or determine if any prior approval program is in operation, before
the replacement of a component.
• NOTE: Generic scan tools may not read the codes listed, or may read only 5-digit codes. Match the 5 digits from the scan
tool to the first 5 digits of the 7-digit code listed to identify the fault (the last 2 digits give extra information read by the
manufacturer-approved diagnostic system).
• NOTE: When performing voltage or resistance tests, always use a digital multimeter (DMM) accurate to three decimal
places, and with an up-to-date calibration certificate. W hen testing resistance always take the resistance of the DMM
leads into account.
• NOTE: Check and rectify basic faults before beginning diagnostic routines involving pinpoint tests.
• NOTE: Inspect connectors for signs of water ingress, and pins for damage and/or corrosion.
• NOTE: If DTCs are recorded and, after performing the pinpoint tests, a fault is not present, an intermittent concern may
be the cause. Always check for loose connections and corroded terminals.
Description And Operation
For a detailed description of the satellite radio system, refer to the relevant Description and Operation section in the
workshop manual.
For additional information, refer to:
Audio System
(415-01 Information and Entertainment System, Description and
Operation).
Satellite Radio Module (SRM)
DTC
Description
Possible Cause
Action
B1A89-11 Satellite
antenna
SDARS antenna circuit - short to
ground
Refer to electrical circuit diagrams and check SDARS antenna
circuit for short to ground
B1A89-12 Satellite
antenna
SDARS antenna circuit - short to
power
Refer to electrical circuit diagrams and check SDARS antenna
circuit for short to power
B1A89-13 Satellite
antenna
SDARS antenna circuit - open
circuit
Refer to electrical circuit diagrams and check SDARS antenna
circuit for open circuit
U3000-04 Control
module
System internal failure
Install a new satellite radio module.
For additional information, refer to:
Satellite Radio Tuner
(415-01
Information and Entertainment System, Removal and Installation).
U3000-4A Control
module
Incorrect component installed
Install a new satellite radio module.
For additional information, refer to:
Satellite Radio Tuner
(415-01
Information and Entertainment System, Removal and Installation).
or Re-configure the satellite radio module using the manufacturer
approved diagnostic system
U3000-55 Control
module
Incorrect Car Configuration File
data received
Check/up-date Car Configuration File using manufacturer approved
diagnostic system
U3000-87 Control
module
Missing message
Check CJB for DTCs and refer to DTC Index.
For additional information, refer to:
Communications Network
(418-00 Module Communications Network, Diagnosis and Testing).
Check information and entertainment module for Car Configuration
File and MOST network DTCs and refer to relevant DTC Index.
Carry out MOST/CAN network tests using the manufacturer
approved diagnostic system
U3000-98 Control
module
Component or system over
temperature
Check for additional DTCs and refer to relevant DTC Index.
Check/monitor system for re-occurrence
U3003-62 Battery
voltage
Mis-match in battery voltage, of
2 volts or more, between
satellite radio module and CJB
Carry out pinpoint tests associated with this DTC using the
manufacturer approved diagnostic system
General Information - Diagnostic Trouble Code (DTC) IndexDTC:
Transmission Control Module (TCM)
Description and Operation
• NOTE: If a control module or component is suspect and the vehicle remains under manufacturer warranty, refer to the
Warranty Policy and Procedures manual (section B1.2), or determine if any prior approval program is in operation, before
the replacement of a component.
• NOTE: Generic scan tools may not read the codes listed, or may read only 5-digit codes. Match the 5 digits from the scan
tool to the first 5 digits of the 7-digit code listed to identify the fault (the last 2 digits give extra information read by the
manufacturer-approved diagnostic system).
• NOTE: When performing voltage or resistance tests, always use a digital multimeter (DMM) accurate to three decimal
places, and with an up-to-date calibration certificate. W hen testing resistance always take the resistance of the DMM
leads into account.
• NOTE: Check and rectify basic faults before beginning diagnostic routines involving pinpoint tests.
• NOTE: Inspect connectors for signs of water ingress, and pins for damage and/or corrosion.
• NOTE: If DTCs are recorded and, after performing the pinpoint tests, a fault is not present, an intermittent concern may
be the cause. Always check for loose connections and corroded terminals.
Description And Operation
For a detailed description of the transmission control system, refer to the relevant Description and Operation section in the
workshop manual. For additional information, refer to:
Transmission Description
(307-01 Automatic
Transmission/Transaxle, Description and Operation).
Transmission control module (TCM)
DTC
Description
Possible Cause
Action
P0218-68 Transmission fluid
overtemperature condition
Transmission fluid level low
Transmission fluid
cooler/hoses are
obstructed/damaged/blocked.
Mechanical fault in the
transmission
Check the transmission fluid level and
condition. Check the transmission fluid cooler
/hoses for signs of obstruction/damage
/blockage. Rectify as necessary. Refer to the
warranty policy and procedures manual if the
transmission is suspect.
P0500-00 Vehicle speed sensor A
(output shaft speed
sensor)
Vehicle speed sensor A
circuit: short circuit to ground
Vehicle speed sensor A
circuit: open circuit
Vehicle speed sensor A fault
Check the vehicle speed sensor A and circuits.
Refer to the electrical guides. Rectify as
necessary.
P056-100 System voltage unstable
Battery fault
Charging system fault
Check the battery and charging systems. Refer
to the electrical guides. Rectify as necessary.
P0562-00 System voltage low
Battery fault
Charging system fault
P0601-00 Internal control module
memory checksum error
Internal transmission control
module (TCM) fault
Reconfigure the module using the approved
diagnostic system.
P0603-00 Internal control module
keep alive memory (KAM)
error
Internal transmission control
module (TCM) fault
Refer to the warranty policy and procedures
manual if the TCM is suspect.
P0604-00 Internal control module
random access memory
(RAM) error
Internal transmission control
module (TCM) fault
P0605-00 Internal control module
read only memory (ROM)
error
Internal transmission control
module (TCM) fault
P0614-00 Engine control module
(ECM)/transmission control
module (TCM) incompatible
Incorrect software in TCM
Reconfigure the module using the approved
diagnostic system.
P062F-00 Internal control module
electrically erasable
programmable read only
memory (EEPROM) error
Internal transmission control
module (TCM) fault
Refer to the warranty policy and procedures
manual if the TCM is suspect.
P0705-00 Transmission range sensor
A circuit (PRNDL input)
Incorrect adjustment of the
gear selector lever cable
Incorrect adjustment of the
gear position sensor
Internal transmission control
module (TCM) fault
Check the adjustment of the gear selector lever
cable and sensor.
For additional information, refer to:
Selector
Lever Cable Adjustment
(307-05 Automatic
Transmission/Transaxle External Controls,
General Procedures).
Refer to the warranty policy and procedures
manual if the TCM is suspect.
P0706-00 Transmission range sensor
A circuit range/performance
Incorrect adjustment of the
gear selector lever cable
Incorrect adjustment of the
gear position sensor
Internal transmission control
Check the adjustment of the gear selector lever
cable.
For additional information, refer to:
Selector
Lever Cable Adjustment
(307-05 Automatic
Transmission/Transaxle External Controls,
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст