Range Rover 2. Electrical Manual — part 166
CRUISE CONTROL
B5
22
TROUBLESHOOTING
OK
OK
PROBLEM CAUSE
OK
OK
5F
3F
4F
CONDITIONS
Ignition Switch
Position: II
Y, YG
CONDITIONS
Ignition Switch
Position: 0
RESULTS
Wire
-
-
D
D
4F
Body Electrical Control
Module (BECM)
2F
PROBLEM CAUSE
OY, YO Wire
-
Turn a drive wheel by hand
D
RESULTS
Z132
Engine Control
Module (ECM)
V
Y
C0411
Less than 1 ohm
Z132
Engine Control
Module (ECM)
YO
C0411
C0895
Z249
Cruise Control
Converter/Inverter
Module
OY
=
4V
Fluctuating
CRUISE CONTROL
B5
23
TROUBLESHOOTING
OK
OK
PROBLEM CAUSE
OK
OK
5F
6F
CONDITIONS
Ignition Switch
Position: 0
YR, W Wire
-
-
D
6F
B, PB
Wire
Rotary Coupler
-
4F
PROBLEM CAUSE
YS, R Wire
-
- Rotary Coupler
Steering Wheel Switches
-
PROBLEM CAUSE
Cruise Control Converter/
Inverter Module
-
RESULTS
Steering Wheel Switches
D
On
Off
Less than 1 ohm
More than 10K ohms
=
=
RES/DECEL Switch
Z249
Cruise Control
Converter/Inverter
Module
C0895
YR
Steering Wheel Switches
-
CONDITIONS
Ignition Switch
Position: 0
D
RESULTS
Steering Wheel Switches
D
On
Off
Less than 1 ohm
More than 10K ohms
=
=
SET/ACCEL Switch
Z249
Cruise Control
Converter/Inverter
Module
C0895
YS
Body Electrical Control
Module (BECM)
-
TRANSFER GEARBOX
B6
CIRCUIT OPERATION
1
CIRCUIT OPERATION
Interface to transfer motor inside Transfer Box
(X313)
The Transmission Gearbox Control Unit (Z256) has
a seven wire interface to the Transfer Motor inside
the Transfer Box (X313), consisting of the four motor
position switches, the ground for the switches and
the drives to move the motor one way or the other.
Motor Position Switches–
pins 17, 32, 33, 7
The Transmission Gearbox Control Unit (Z256)
reads the position of the motor in the form of a
binary Gray Code.
So the Transmission Gearbox Control Unit (Z256)
can find out in which gear the Transfer Box (X313) is
in and where the motor should move to, to engage
the desired range. If the Transfer Box (X313) moves
outside the normal modes (e.g. Left of High) then the
Transmission Gearbox Control Unit (Z256) can move
the motor back to the correct position.
Motor Position Switch ground–
pin 19
The switches on the transfer box motor are
referenced to pin 19, i.e. if there is a problem with
the harness to pin 19 then the Transmission
Gearbox Control Unit (Z256) will not be able to
assess where the transfer motor is and so will not
move the motor.
Motor drive Clockwise (pins 25, 26) and Counter
Clockwise (pins 1, 2)
The Transmission Gearbox Control Unit (Z256)
receives signals from the motor position switches,
the drivers request, the vehicle speed and the
transmission neutral signal and, when the
parameters are correct, powers the motor from one
mode to another via the motor drives. This is actually
a single wire interface for each direction which is
split down to two wires at the Transmission Gearbox
Control Unit (Z256) to help pass the current though
two pins rather than one. If there is a problem with
either the motor drives or the harness, then the
motor will not move and a range change will not be
possible.
Vehicle Speed Sensor–
pins 13, 30
The Transmission Gearbox Control Unit (Z256)
senses how fast the vehicle is travelling, compares
this speed to the value stored in the memory and
decides if a range change is allowed. Presently the
shift speeds are set at 5 mph High to Low and Low
to High on vehicles with an automatic transmission
and 15 mph Low to High on vehicles with a manual
transmission.
Interface to BeCM (Z238)
High, Low and Neutral Status Lamps
–
pins 35, 14, 36
The Transmission Gearbox Control Unit (Z256)
informs the BeCM (Z238), which informs the
Instrument Pack (Z142), about the range the vehicle
is in via three status lamps.
When a range change is requested, the desired
range will flash up on the display (i.e. “HIGH”) and
continue flashing until the range change is achieved.
When complete, the range message will switch to
constant and be displayed for a few seconds.
If a range change is requested and not all of the
conditions are satisfied then the desired range
message will flash and continue flashing until all of
the parameters are satisfied or the request is
removed.
If the transfer box neutral is selected then, after a
five second safety delay, the Transfer Box (X313)
moves to neutral and the display shows “NEUTRAL”.
The High and Low status lamp signals also pass
information to the H–Gate and the Auto Gear Box
Control Unit (Z255).
Interface to Engine Control Module
(ECM) (Z132)
On North American Specification (NAS) vehicles, the
inability of the Transfer Gear Box ECU (Z256) to
move into the High range is flagged over the fault
output line. A fault will also be flagged in the event of
a speed sensor failure or incorrect transfer motor
position information. The Malfunction Indicator Lamp
(MIL) will illuminate if a fault is recorded on two
successive journeys.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст