Defender 300Tdi (1996+). Manual — part 49
REAR AXLE AND FINAL DRIVE
11
OVERHAUL
Refit
7. Clean hub and fit inner and outer bearing tracks.
8. Pack hub inner bearing with grease and fit to
hub.
9. With lip side leading, fit a new seal flush with
rear face of hub. Using service tool LRT-54-003
(LST137) seal replacer and drift. Apply grease
between seal lips.
10. Assemble brake disc to hub, line up reassembly
marks. Applying Loctite 270, fit and tighten
retaining bolts to
73 Nm (54 lbf/ft).
11. Pack hub outer bearing with grease and fit to
hub.
12. Fit rear hub assembly
See Repair, Rear hub
assembly .
51
REAR AXLE AND FINAL DRIVE
12
OVERHAUL
REAR STUB AXLE - 90
Service repair no - 64.15.22.
STUB AXLE COMPONENTS
1. Stub axle to axle casing bolt.
2. Mudshield.
3. Stub axle.
4. Stub axle joint washer.
5. Axle case.
Overhaul
1. Remove hub assembly
See Repair, Rear hub
assembly .
2. Remove 6 bolts from stub axle to axle casing.
3. Remove mudshield.
4. Remove stub axle and joint washer.
Renew rear stub axle oil seal
5. Remove and discard oil seal. Lubricate seal and
lip with EP90 oil. Using special tool LRT-51-004
(LST 138) fit new oil seal lip side trailing so that
seal is flush with rear face of stub axle.
Refit
6. Fit new joint washer, stub axle and mudshield
bolts. Tighten bolts to
65 Nm (48 lbf/ft).
7. Refit hub assembly
See Repair, Rear Hub
Assembly .
REAR AXLE AND FINAL DRIVE
13
OVERHAUL
REAR HUB - 110/130
Service repair no - 64.15.14.
Overhaul
1. Remove rear hub assembly
See Repair, Rear
hub assembly.
2. Remove outer bearing.
3. Mark, for reassembly, relationship between hub
and brake disc, if original hub is to be refitted.
4. Remove 5 bolts and separate hub from brake
disc.
5. Drift out grease seal and inner bearing from hub
and discard seal.
HUB COMPONENTS
1. Dust cap.
2. Drive shaft circlip.
3. Drive member.
4. Drive member joint washer.
5. Drive member retaining bolt.
6. Lock nut.
7. Lock washer.
8. Hub adjusting nut.
9. Spacing washer.
10. Outer bearing.
11. Hub.
12. Inner bearing.
13. Grease seal.
14. Brake disc.
15. Disc retaining bolt.
51
REAR AXLE AND FINAL DRIVE
14
OVERHAUL
6. Drift out inner and outer bearing tracks.
7. Clean hub and drift in inner and outer bearing
tracks.
8. Pack hub inner bearing with recommended
grease and fit to hub.
9. With lip side leading, fit new seal to hub using
special tool LRT-54-003 (LST 137) seal replacer
and drift 18G 134. Drive in seal flush with rear
face of hub. Apply grease between seal lips.
10. Fit brake disc to hub, lining up to marks made
during dismantling. apllying Loctite 270, fit
retaining bolts. Tighten to
73 Nm (54 lbf/ft).
11. Grease and fit outer bearing to hub.
12. Fit hub assembly
See Repair, Rear hub
assembly .
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст