Defender. Manual — part 148
(103kW/140PS) - Puma, Removal and Installation).
Clear the DTCs and test for normal operation. Refer to
the warranty policy and procedures manual if a module is
suspect.
P029C00 Cylinder 1 balance -
(injector 1) restricted
Injector leak
Cylinder
compression low
- Blow-by past
the injector
- Blow-by past
the glow plug
- Mechanical
fault, valve,
piston/ring,
etc.
Injector fault
Check the injector and surrounding area for evidence of
fuel leakage. Disconnect the injector and check for
evidence of fuel leakage in the connector. Rectify as
necessary. Clear the DTCs. Reconnect the injector and
start the engine. Allow to warm up and allow to idle
(cylinder balance diagnosis is now active). If the DTC
resets, check for blow-by etc. and rectify as necessary.
Clear the DTCs and recheck. Carry out a compression test
only if the DTC resets. If the above tests are all within
range, install a new injector.
REFER to:
Fuel Injector
(303-04A Fuel Charging and
Controls - 2.4L Duratorq-TDCi HPCR (103kW/140PS) -
Puma, Removal and Installation).
Clear the DTCs and test for normal operation.
P02A000 Cylinder 2 balance -
(injector 4) restricted
Injector leak
Cylinder
compression low
- Blow-by past
the injector
- Blow-by past
the glow plug
- Mechanical
fault, valve,
piston/ring,
etc.
Injector fault
Check the injector and surrounding area for evidence of
fuel leakage. Disconnect the injector and check for
evidence of fuel leakage in the connector. Rectify as
necessary. Clear the DTCs. Reconnect the injector and
start the engine. Allow to warm up and allow to idle
(cylinder balance diagnosis is now active). If the DTC
resets, check for blow-by etc. and rectify as necessary.
Clear the DTCs and recheck. Carry out a compression test
only if the DTC resets. If the above tests are all within
range, install a new injector.
REFER to:
Fuel Injector
(303-04A Fuel Charging and
Controls - 2.4L Duratorq-TDCi HPCR (103kW/140PS) -
Puma, Removal and Installation).
Clear the DTCs and test for normal operation.
P02A400 Cylinder 3 balance -
(injector 2) restricted
Injector leak
Cylinder
compression low
- Blow-by past
the injector
- Blow-by past
the glow plug
- Mechanical
fault, valve,
piston/ring,
etc.
Injector fault
Check the injector and surrounding area for evidence of
fuel leakage. Disconnect the injector and check for
evidence of fuel leakage in the connector. Rectify as
necessary. Clear the DTCs. Reconnect the injector and
start the engine. Allow to warm up and allow to idle
(cylinder balance diagnosis is now active). If the DTC
resets, check for blow-by etc. and rectify as necessary.
Clear the DTCs and recheck. Carry out a compression test
only if the DTC resets. If the above tests are all within
range, install a new injector.
REFER to:
Fuel Injector
(303-04A Fuel Charging and
Controls - 2.4L Duratorq-TDCi HPCR (103kW/140PS) -
Puma, Removal and Installation).
Clear the DTCs and test for normal operation.
P02A800 Cylinder 4 balance -
(injector 3) restricted
Injector leak
Cylinder
compression low
- Blow-by past
the injector
- Blow-by past
the glow plug
- Mechanical
fault, valve,
piston/ring,
etc.
Injector fault
Check the injector and surrounding area for evidence of
fuel leakage. Disconnect the injector and check for
evidence of fuel leakage in the connector. Rectify as
necessary. Clear the DTCs. Reconnect the injector and
start the engine. Allow to warm up and allow to idle
(cylinder balance diagnosis is now active). If the DTC
resets, check for blow-by etc. and rectify as necessary.
Clear the DTCs and recheck. Carry out a compression test
only if the DTC resets. If the above tests are all within
range, install a new injector.
REFER to:
Fuel Injector
(303-04A Fuel Charging and
Controls - 2.4L Duratorq-TDCi HPCR (103kW/140PS) -
Puma, Removal and Installation).
Clear the DTCs and test for normal operation.
P033529 Condition and fitment of
the crankshaft position
(CKP) sensor A circuit -
signal invalid
CKP sensor
CKP sensor
circuit: short
circuit to ground
CKP sensor
circuit: short
circuit to power
CKP sensor
circuit: open
circuit
CKP sensor fault
CKP sensor wheel
fault
Check the CKP sensor and circuits. Refer to the electrical
guides. Check the sensor and wheel for correct
installation and condition. Rectify as necessary. Install a
new CKP sensor if necessary.
REFER to:
Crankshaft Position (CKP) Sensor
(303-14
Electronic Engine Controls - 2.4L Duratorq-TDCi HPCR
(103kW/140PS) - Puma, Removal and Installation).
Clear the DTCs and test for normal operation.
P033531 Condition and fitment of
the crankshaft position
(CKP) sensor A circuit - no
signal
CKP sensor
CKP sensor
circuit: short
circuit to ground
CKP sensor
circuit: short
circuit to power
CKP sensor
circuit: open
circuit
CKP sensor fault
CKP sensor wheel
fault
P034023 Camshaft position (CMP)
sensor A circuit (bank 1 or
single sensor) - signal
stuck low
CMP sensor
circuit: short
circuit to ground
CMP sensor
circuit: short
circuit to power
CMP sensor
circuit: open
circuit
CMP sensor fault
Check the CMP sensor and circuits. Refer to the electrical
guides. Install a new CMP sensor if necessary.
REFER to:
Camshaft Position (CMP) Sensor
(303-14
Electronic Engine Controls - 2.4L Duratorq-TDCi HPCR
(103kW/140PS) - Puma, Removal and Installation).
Clear the DTCs and test for normal operation.
P034024 Camshaft position sensor
(CMP) A circuit (bank 1 or
single sensor) - signal
stuck high
CMP sensor
circuit: short
circuit to ground
CMP sensor
circuit: short
circuit to power
CMP sensor
circuit: open
circuit
CMP sensor fault
P037D29 Glow plug relay sensor
circuit - signal invalid
Glow plug short
circuit to ground
Relay circuit to
relay
Relay circuit from
relay
Glow plug relay
fault
Check the relay and circuits. Refer to the electrical
guides. Activate the relay and check for an audible
"click". Rectify as necessary. Clear the DTCs and test for
normal operation.
P038011 Glow plug/heater circuit A
- circuit short to ground
Glow plug relay
control circuit:
short circuit to
ground
Glow plug relay
fault
Check the relay and circuits. Refer to the electrical
guides. Activate the relay and check for an audible
"click". Rectify as necessary. Clear the DTCs and test for
normal operation.
P038015 Glow plug/heater circuit A
- circuit short to battery
or open
Glow plug relay
control circuit:
short circuit to
power
Glow plug relay
control circuit:
open circuit
Glow plug relay
fault
P04031A Exhaust gas recirculation
(EGR) control circuit -
circuit resistance below
threshold
EGR control valve
actuator circuit:
short circuit to
ground
EGR control valve
actuator circuit:
short circuit to
power
EGR control valve
actuator circuit:
open circuit
EGR control valve
fault
Check the EGR control valve actuator and circuits. Refer
to the electrical guides. Install a new EGR valve if
necessary.
REFER to:
Exhaust Gas Recirculation (EGR) Valve
(303-
08 Engine Emission Control - 2.4L Duratorq-TDCi HPCR
(103kW/140PS) - Puma, Removal and Installation).
Clear the DTCs and test for normal operation.
P04031B Exhaust gas recirculation
(EGR) control circuit -
circuit resistance above
threshold
EGR control valve
actuator circuit:
short circuit to
ground
EGR control valve
actuator circuit:
short circuit to
power
EGR control valve
actuator circuit:
open circuit
EGR control valve
fault
P040311 Exhaust gas recirculation
(EGR) control circuit -
EGR control valve
actuator circuit:
circuit short to ground
short circuit to
ground
EGR control valve
fault
P040312 Exhaust gas recirculation
(EGR) control circuit -
circuit short to battery
EGR control valve
actuator circuit:
short circuit to
power
EGR control valve
fault
P040472 Exhaust gas recirculation
(EGR) control circuit
range/performance -
actuator stuck open
EGR control valve
actuator circuit
fault
EGR control valve
fault
Check the EGR control valve actuator and circuits. Refer
to the electrical guides. Install a new EGR valve if
necessary.
REFER to:
Exhaust Gas Recirculation (EGR) Valve
(303-
08 Engine Emission Control - 2.4L Duratorq-TDCi HPCR
(103kW/140PS) - Puma, Removal and Installation).
Clear the DTCs and test for normal operation.
P040473 Exhaust gas recirculation
(EGR) control circuit
range/performance -
actuator stuck closed
EGR control valve
actuator circuit
fault
EGR control valve
fault
P048000 Fan 1 control circuit on/off
Cooling fan
control circuit:
short circuit to
ground
Cooling fan
control circuit:
short circuit to
power
Cooling fan
control circuit:
open circuit
Cooling fan fault
Check the cooling fan and circuits. Refer to the electrical
guides. Install a new cooling fan if necessary.
REFER to:
Cooling Fan
(303-03 Engine Cooling - 2.4L
Duratorq-TDCi HPCR (103kW/140PS) - Puma, Removal
and Installation).
Clear the DTCs and test for normal operation.
P05032F Vehicle speed sensor
(VSS) A
intermittent/erratic/high -
signal erratic
VSS A circuit:
short circuit to
ground
VSS A circuit:
short circuit to
power
VSS A circuit:
open circuit
VSS A fault
Check for instrument cluster related DTCs. Rectify as
necessary. Check the VSS sensor and circuits. Refer to
the electrical guides. Rectify as necessary. Clear the DTCs
and test for normal operation.
P050337 Vehicle speed sensor
(VSS) A
intermittent/erratic/high -
signal frequency too high
VSS A circuit:
short circuit to
ground
VSS A circuit:
short circuit to
power
VSS A circuit:
open circuit
VSS A fault
Check for instrument cluster related DTCs. Rectify as
necessary. Check the VSS sensor and circuits. Refer to
the electrical guides. Rectify as necessary. Clear the DTCs
and test for normal operation.
P052015 Engine oil pressure (EOP)
sensor switch circuit -
circuit short to battery or
open
EOP sensor/switch
circuit: short
circuit to power
EOP sensor/switch
circuit: open
circuit
EOP sensor/switch
fault
Check the EOP sensor/switch and circuits. Refer to the
electrical guides. Install a new EOP sensor if necessary.
REFER to:
Engine Oil Pressure (EOP) Sensor
(303-14
Electronic Engine Controls - 2.4L Duratorq-TDCi HPCR
(103kW/140PS) - Puma, Removal and Installation).
Clear the DTCs and test for normal operation.
P056200 System voltage low
Battery
condition/state of
charge
Charging system
fault
Check the battery condition and state of charge. Check
the charging system. Install a new generator if
necessary.
REFER to:
Generator
(414-02 Generator and Regulator -
2.4L Duratorq-TDCi HPCR (103kW/140PS) - Puma,
Removal and Installation).
Clear the DTCs and test for normal operation.
P056300 System voltage high
Battery
condition/state of
charge
Charging system
fault
P057100 Brake switch A circuit
Brake switch
circuit: short
circuit to power
Brake switch
circuit: short
Check the brake switch and circuits. Refer to the
circuit: short
circuit to ground
Brake switch
circuit: open
circuit
Brake switch fault
electrical guides. Install a new brake switch if necessary.
Clear the DTCs and test for normal operation.
P060200 Engine control module
(ECM) programming error
Fuel programming
error
Reprogramme the module using the approved diagnostic
system. Refer to the warranty policy and procedures
manual if a module is suspect.
P060543 Internal control module
read only memory (ROM)
error -special memory
failure
Engine control
module (ECM)
programming
error
Reprogramme the module using the approved diagnostic
system. Refer to the warranty policy and procedures
manual if a module is suspect.
P060554 Internal control module
read only memory (ROM)
error - missing calibration
Engine control
module (ECM)
programming
error
P060616 Engine control module
(ECM) processor - circuit
voltage below threshold
ECM fault
Refer to the warranty policy and procedures manual if the
ECM is suspect.
P060647 Engine control module
(ECM) processor -
watchdog failure
ECM fault
P060649 Engine control module
(ECM) processor- internal
electronic failure
ECM fault
P060696 Engine control module
(ECM) processor -
component internal failure
ECM fault
P061000 Control module vehicle
options error
Tyre size is
incompatible with
the central car
configuration
Check tyre sizes are of the correct specification. Rectify
as necessary. Check correct central car configuration
software is installed. Reprogramme the module as
necessary.
P061512 Starter relay circuit -
circuit short to battery
Starter relay
circuit: short
circuit to power
Check the starter relay circuits. Refer to the electrical
guides. Rectify as necessary. Clear the DTCs and test for
normal operation.
P061514 Starter relay circuit -
circuit short to ground or
open
Starter relay
circuit: short
circuit to ground
Starter relay
circuit: open
circuit
P062211 Generator field terminal
circuit - circuit short to
ground
Generator field
terminal circuit:
short circuit to
ground
Generator fault
Check the charging voltage. Check the charging system
circuits. Refer to the electrical guides. Install a new
generator if necessary
REFER to:
Generator
(414-02 Generator and Regulator -
2.4L Duratorq-TDCi HPCR (103kW/140PS) - Puma,
Removal and Installation).
Clear the DTCs and test for normal operation.
P062215 Generator field terminal
circuit - circuit short to
battery or open
Generator field
terminal circuit:
short circuit to
power
Generator field
terminal circuit:
open circuit
Generator fault
P062300 Generator lamp control
circuit
Check generator
belt is not broken,
excessively worn
or slipping when
engine running
Generator lamp
control circuit
fault
Generator fault
Check the charging voltage. Install a new accessory drive
belt if necessary.
REFER to:
Accessory Drive Belt
(303-05 Accessory Drive -
2.4L Duratorq-TDCi HPCR (103kW/140PS) - Puma,
Removal and Installation).
Check the charging system circuits. Check the generator
lamp control circuit. Refer to the electrical guides. Install
a new generator if necessary.
REFER to:
Generator
(414-02 Generator and Regulator -
2.4L Duratorq-TDCi HPCR (103kW/140PS) - Puma,
Removal and Installation).
Clear the DTCs and test for normal operation.
P062B16 Internal control module
fuel injector control
performance - circuit
voltage below threshold
Engine control
module (ECM)
fault
Refer to the warranty policy and procedures manual if the
ECM is suspect.
P062B17 Internal control module
fuel injector control
performance - circuit
voltage above threshold
Engine control
module (ECM)
fault
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст