Range Rover Classic. Manual — part 165
HEATING AND VENTILATION
3
REPAIR
Air direction
3. Set control fully clockwise
4. Release outer cable from 2 clips on unit.
5. Release cable from stud on flap lever.
6. Remove control cable from control lever.
Temperature
7. Set RH control fully clockwise, LH control fully
anti-clockwise
8. Release outer cable from 2 clips on unit.
9. Release cable from stud on flap lever.
10. Remove control cable from control lever.
Refit
11. Reverse removal procedure. Check the
satisfactory function of the controls before fitting
louvre vent panel.
RESISTOR UNIT
Service repair no - 80.20.17
Remove
1. Open glove box, manoeuvre side springs
through cut-outs and lower lid.
2. Remove 2 screws securing resistor unit to
trunking.
3. Disconnect multiplug and remove resistor unit.
Refit
4. Reverse removal procedure.
80
HEATING AND VENTILATION
4
REPAIR
WATER VALVE
Service repair no - 80.10.16
Remove
1. Disconnect vacuum pipe from water valve.
2. Slacken 4 clips securing hoses to water valve.
3. Use a thin blade to break seal between hoses
and nozzles
4. Disconnect heater inlet hose from valve.
NOTE: A quantity of coolant will be
released.
5. Disconnect heater outlet hose from valve.
6. Lever valve from coolant pipe hoses.
Refit
7. Reverse removal procedure. Lightly lubricate
water valve nozzles with petroleum jelly.
8. Reverse removal procedure. Top-up engine
coolant
VACUUM SWITCH - WATER VALVE
Service repair no - 80.10.36
Remove
1. Release emission pipe from retaining clip.
2. Remove bolt securing switch to bulkhead.
3. Disconnect multiplug from switch.
4. Disconnect 2 vacuum pipes and remove vacuum
switch.
Refit
5. Reverse removal procedure.
HEATING AND VENTILATION
5
REPAIR
RECIRCULATION SWITCH
Service repair no - 80.10.27
Remove
1. Release fascia centre louvre vent panel from its
fitted position to gain access to rear of panel.
See CHASSIS AND BODY, Repair, Dash
Panel Central Louvre Panel
2. Disconnect multiplug from switch
3. From the rear, push switch out of panel.
Refit
4. Reverse removal procedure.
RECIRCULATION FLAP SOLENOID
Service repair no - 80.10.43
Remove
1. Open glove box, manoeuvre side springs
through cut-outs and lower lid.
2. Remove 2 locknuts securing cruise control ECU
to bracket.
3. Position cruise control ECU aside.
4. Remove 2 screws securing recirculation
solenoid to casing.
5. Release solenoid from lever.
6. Disconnect multiplug and remove solenoid.
Refit
7. Reverse removal procedure.
80
HEATING AND VENTILATION
6
REPAIR
BLOWER MOTOR UNIT - HEATER AND AIR
CONDITIONING
Service repair no - 80.20.17
Service repair no - 82.25.54.
Remove
1. Move seats to rear most position.
2. Disconnect battery negative lead.
3. Remove fascia panel assembly.
See CHASSIS
AND BODY, Repair, Dash Panel Assembly
4. Remove 2 nuts securing lower brackets to
toeboard.
5. Manoeuvre blower unit from heater unit and
remove.
Refit
6. Reverse removal procedure. Ensure seal
between blower and heater unit is tight.
BLOWER MOTOR
Service repair no - 80.20.17
Service repair no - 82.25.33.
Remove
1. Remove blower motor unit.
See Blower Motor
Unit - Heater and Air Conditioning
2. Release wiring harness retaining clip.
3. Remove 3 screws securing casing.
4. Remove blower motor assembly.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст